• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.61-72
• /
• 2004

This study investigated the inelastic lateral-torsional buckling of simply supported beams under a central concentrated load and a uniformly distributed load. A line-type finite element, method was incorporated with the "so-called" simplified and polynomial patterns of residual stresses. The effect of the load height was also considered in this study. The polynomial residual stresses assumed in this study was a quartic distribution in the flange and a parabolic distribution in the web. The inelastic lateral-torsional buckling of beam was analyzed with four different I-sections manufactured in Korea. Results obtained in this study were compared with KSDM(design method in the 1995 Korean Steel Designers' Manual). The design method in KSDM was found to be generally conservative with and without a sub-beam attached to the main beam, which acted as an intermediate restraint.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.14 no.1
• /
• pp.24-31
• /
• 2018

The mechanical design procedure is studied for the PCHE(printed circuit heat exchanger) with electrochemical etched flow channels. The effective heat transfer plates of PCHE are assembled by diffusion bonding to make a module. PCHE is widely used for industrial applications due to its compactness, cost efficiency, and serviceability at high pressure and/or temperature conditions. The limitations and technical barriers of PCHE are investigated for application to nuclear components. Rules for design and fabrication of PCHE are specified in ASME Section VIII but not in ASME Section III of nuclear components. Therefore, the calculation procedure of key dimensions of PCHE is defined based on ASME section VIII. The effective heat transfer region of PCHE is defined by several key dimensions such as the flow channel radius, edge width, wall thickness, and ridge width. The mechanical design procedure of key dimensions was incorporated into a program for easy use in the PCHE design. The effect of assumptions used in the key dimension calculation on stress values is numerically investigated. A comparative analysis is done by comparing finite element analysis results for the semi-circular flow channels with the formula based sizing calculation assuming rectangular cross sections.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.2
• /
• pp.123-131
• /
• 2001

The objective of this study is to investigate the criteria of the width-to-thickness ratio and to evaluate the buckling strength of high strength steel beam-columns and to compare their buckling strength with design codes, which are the Limit State Design code and the Allowable Stress Desogn code(drift). SM520TMC and SM570Q class steels are used for high strength steels. The coupon test and the stub column test were carried out to investigate the properties of high strength steels and the stress-strain curves of stub columns. The buckling strength of high strength steel beam-columns are assessed by numerical analysis used axial force, moment and curvature relationships.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.4
• /
• pp.433-442
• /
• 2009

In this paper, new three-dimensional vibration data for the solid cylinders of the N-sided polygonal cross-section with V-notches or sharp cracks are presented, and a Ritz procedure is employed, which incorporates a mathematically complete set of algebraic-trigonometric polynomials in conjunction with an admissible set of edge functions that explicitly model the tri-axial stress singularities that exist along a terminus edge of the V-notch. Convergence studies demonstrate the necessity of adding the edge functions to achieve the accurate frequencies and mode shapes of N-sided polygonal cylindrical solids with stress singularities.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.180.2-181
• /
• 2003

벼는 미립내부의 온도 및 함수율의 차이에 의해 열응력 및 수분차에 의한 응력이 발생하게 되며, 응력이 과대하게 발생되면 낟알이 금이 가는 동할이 발생하게 된다. 동할은 주로 건조과정 또는 건조후에 주로 발생하게 되는데 벼의 품질에 가장 중요한 지표로서 동할이 발생되면 저장성이 저하되며, 도정시 싸라기가 증가하여 도정수율에도 많은 손실을 가져오게 된다. 본 연구는 함수율 20.01, 21.80 및 22.80%(w.b.) 3수준에 대하여 40.4, 50.0 및 60.9$^{\circ}C$ 3수준의 건조온도와 노출시간 5 ~ 120분 동안에 벼의 동할에 미치는 영향을 구명하고, 동할 예측모델을 개발하는데 목적이 있다. 초기 함수율이 낮고 건조온도가 높을수록 노출시간이 경과할수록 동할은 증가하는 것으로 나타났다. 건조온도 40.4$^{\circ}C$에서는 노출 100분전까지는 동할율이 2%이상 발생하지 않는 것으로 나타났으며, 건조온도 50.$0^{\circ}C$와 60.9$^{\circ}C$에서는 함수율 20.0%(w.b.)의 경우 27분 및 11분 노출했을 때 동할율이 2%이상 발생하였다. 동할 실험치를 실험모델에 적합시켜 다중회귀분석 프로그램을 이용하여 실험상수를 결정하였다. 실험모델의 결정계수는 모든 온도에서 0.9이상으로 높게 나타났으며, RMSE는 40.4$^{\circ}C$에서는 0.2230, 50.$0^{\circ}C$에서는 2.4975로 나타났다. 또한, 60.9$^{\circ}C$에서는 77813로 이는 동할 실험치가 0 ~ 100 사이의 값임을 고려할 때 허용 가능한 수준으로 판단된다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.1
• /
• pp.75-82
• /
• 1999

일반 해양 구조물이나 해저면에 설치되는 해저 관로는 외력에 의한 변형이 발생된다. 구조물 형상이 복잡하거나, 구성 요소의 개수가 많을 경우 응력해석 시 많은 초기값이 필요하고 해석 시간 또는 장 시간 소요된다. 해양 구조물에 작용하는 대표적인 외력은 파도, 조류, 바람이고 이런 외력은 구조물의 사용 기간(operation life)동안 계속적으로 작용하기 때문에 구조물의 변형율은 항상 허용치 안에서 발생되도록 설계되어야 한다. 허용 변형은 탄성범위 내에 존재해야 하며, 비교적 큰 변형을 일으키는 구조물이나 해저파이프라인의 응력해석을 수치적으로 접근하는 방법을 고찰하였다. 평행상태의 하중 벡터값만 직각 좌표계에서 인트린직(intrinsic) 좌료로 변환시킬 때 변형이 발생함으로, 본 논문에서 소개하는 이차 요소(quadratic element)방법을 사용할 경우 수치해석 시 많은 장점이 있다는 것을 보여준다. 본 방법을 도입함으로써 비교적 큰 변형이 발생되는 구조물 해석 시 일반 수치해석 방법과 그 결과는 같으나 해석 시간을 단축시킬 수 있다는 장점이 있다. 응력 해석 시 국부 강도 행열(element stiffness matrix)은 방향과 무관하며 이차요소 방법을 사용하여 각 요소 벡터를 발생시켰다. 해저관로 일점 상승 시 관로에 작용하는 변형과 상승력에 따른 휨 모멘트를 산출하여 일반적으로 사용되는 선형이론과 비교하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.91-100
• /
• 2004

A Green's function approach is adopted for analyzing the thermoelastic deformations and stresses of a plate made of functionally graded materials(FGMs). The solution to the 3-dimensional unsteady temperature is obtained by using the laminate theory. The fundamental equations for thermoelastic problems are derived in terms of out-plane deformation and in-plane force, separately. The thermoelastic deformation and the stress distributions due to the bending and in-plane forces are analyzed by using a Green's function based on the Galerkin method. The eigenfunctions of the Galerkin Green's function for the thermoelastic deformation and the stress distributions are approximated in terms of a series of admissible functions that satisfy the homogeneous boundary conditions of the rectangular plate. Numerical analysis for a simply supported plate is carried out and effects of material properties on unsteady thermoclastic behaviors are discussed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.2
• /
• pp.223-230
• /
• 2012

The strength of brittle material has commonly been characterized by a normal distribution or Weibull distribution, but it may fit the gamma distribution for some material. The use of an extreme value distribution is proper when the largest values of a set of stresses dominate the failure of the material. This paper presents a formula for reliability estimation based on stress-strength interference theory that is applicable when the strength of material is distributed like a gamma distribution and the stress is distributed like an extreme value distribution. We verified the validity of the equation for the reliability estimation by examining the relationships among the factor of safety, the coefficient of variation, and the reliability. The required minimum factor of safety and the highest allowable coefficient of variation of stress can be estimated by choosing an objective reliability and estimating the reliabilities obtained for various factors of safety and coefficients of variation.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.137-146
• /
• 2010

This study was conducted to develop the design methodology of gap slabs for the post-tensioned concrete pavement (PTCP). The gap slabs were considered as unbonded, half bonded, and bonded types. According to the types of the gap slabs, the curling stresses were investigated first under the environmental loads. The stresses due to the vehicle loads were analyzed considering both the single and tandem axles. The method to calculate the prestressing amount was suggested by comparing the combined stresses due to both loads and the allowable tensile stress of concrete. The prestressing amount for the unbonded type gap slab could be designed by considering only the gap slab; however, for the half bonded and bonded gap slabs, the whole PTCP slab should be analyzed to properly design the prestressing amount.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.9
• /
• pp.5769-5777
• /
• 2015

According to the forming or bending deformation in the press die, the thin plate occurs a work-hardening, the sheet hardening and cam unit's deformation causes incomplete forming during the cam molding process by the reacting spring forces. This study treated the input parameters of the stress and strain as given properties and also used Cam forming pressure considering the sheet hardening in the forming process of the aluminum sheet. The Hyperstudy are operated be linked with the Abaqus of the finite element analysis tool and the shape of Cam were carried out with non-linear shape optimization analysis. As a result removing the deformation of plate, the cam shape were optimized under conditions reduced deformation, having a minimum stress range and the minimum deformation. Therefore, a stress-strain curve and a normal distribution of stress-thickness can be obtained and optimization could be obtained for the shape of the stress and strain on the die plate hardened cam considering the thickness and reaction force of gas spring as iteration process.