• Analytical Science and Technology
• /
• v.10 no.6
• /
• pp.418-426
• /
• 1997

Dewatered digested sewage sludge were heated with microwave and their drying characteristics were investigated on the effect of their surface area, shape, diameter and thickness. The drying characteristics of identical samples in a conventional drying oven were studied. In conventional drying, constant rate period was not found and moisture was evaporated with capillary action. Moisture in the sludge was a bound water and free water was not exist. In microwave drying, the falling rate period was divided into two zones. In falling rate drying period, moisture movement occured by diffusion. The evaporation surface area was a significant variable, the greater heating surface area promoted water removal rate over wide region of water content. Drying rate was slow and constant rate drying period was found in wide moisture content region with increasing diameter. Drying characteristics appeared differently in various shape. In microwave heating, first of all temperature of sludge center was increased and was the highest. Temperature in the constant rate drying period was remained constantly at $80{\sim}100^{\circ}C$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.5
• /
• pp.68-75
• /
• 1996

The vacuum drying characteristics of water-saturated porous media were studied experimentally. The water-saturated porous media, water-saturated sand layer, was heated by the isothermal bottom wall of the rectangular vessel. The vacuum drying rate and temperature distribution of the sand layer were measured and calculated under a variety of conditions of heated wall temperature, vacuum rate, and thickness of the test material. It was found that the drying rate due to the heat and mass teansfer is greatly influenced by the heated wall temperature, vacuum rate, and thickness of the test material.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.3
• /
• pp.588-594
• /
• 2001

The aim of this paper is to develop the low temperature vacuum dryer, with low initial investments and operating costs, easy operating method and trouble-free operation Usally operations just below atmospheric pressure, as with direct dryers, but some are built for vacuum operation with pressure as low 50 mmHg abs. The lowers the boiling point to $39^{\circ}C$ The experimental data of quantitative analysis for using practically were obtained by the constant drying rate period and reducing drying rate period according to the temperature of hot water which is the experimental parameters of present experiment. As the results, it took about 20 hours for material to reach about 18% of the final moisture content is order to store products for a long time about 450% of the early moisture content at the beginning of drying and maximum drying rate comes to about 0.30 kg/m2hr at about 350% of the moisture content.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.46-51
• /
• 2011

Low temperature vacuum drying technique, whose drying time and quantity of exhausting energy is about 25~30% of hot air drying, is very excellent in the drying efficiency. This paper is made out in the aspects of heat engineering with the object of developing Korean drying machine which can dry once a large quantity of objects to be dried in the state of low temperature and vacuum. As the results, it took about 17 hours(3~4 days in case of hot air drying) for material to reach about 18% of the final moisture content in order to store products for a long time, from about 78~80% of the early moisture content at the beginning of drying, and maximum drying rate comes to about 0.35 kg/m2hr at about 400% of the moisture content.

• Journal of Power System Engineering
• /
• v.14 no.4
• /
• pp.23-28
• /
• 2010

Of the roughly four million known substances, about 60,000 are processed and sold ; many of these must be dried. Many materials are processed in the liquid state - ideal for mixing and reacting - but most products are needed or wanted as dry, or relatively dry, solids. Usually operation is just below atmospheric pressure, as with direct dryers, but some are built for vacuum operation with pressures as low as 26.66kPa abs.. In spite of the global-class aquiculture agriculture and fisheries technology of our country, the processing technologies are lags behind the other nations relatively. These problems are considered to be caused directly by the lack of drying technologies. This paper is concerned to the experimental results of drying heat transfer characteristics for the green energy type vacuum dryer for the high quality agriculture and fisheries production.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.4
• /
• pp.427-434
• /
• 2000

In tradition, there have been two kinds of drying methods, which are sun drying and artificial drying. The sun drying method which has been adopted traditionally has been replaced by the hot-air drying method which is one of the most general methods of artificial drying, with its simple drying system, low initial cost of drying plant, and easy operating method. But the hot-air drying method has some defects; (1) much energy loss happens due to the discharge of hot air during the drying process, (2) control of drying rate is not easy on account of changing relative humidity of inlet air for uniform hot air temperature, (3) high temperature of foods in drying process brings about the production of low-grade drying products. Vacuum drying takes advantage of energy saving and mass production because it reduces the drying time by increasing the drying rate under low temperature condition. The aim of this paper is to develop the low temperature vacum dryer, with low initial investments and operating costs, easy operating method and trouble-free operation.

• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.58-64
• /
• 1982

The fresh threshed paddy-mat dryings on the various environments were analyzed on their drying characteristics and rice quality resulted. The moisture content of paddy was mainly determined by the accumulated solar energy received, and which was expressed as a simple equation. The drying characteristics revealed to follow a constant rate drying type, and as the depth increased the more typical constant-rate drying pattern was observed. The relationship between the drying rate and bed depth was established with a simple exponential equation. The raking operation during the drying period showed a favorable effect both on the drying rate and the reduction of crack formation. Drying environments such as straw mat, concrete, ground, polyethylene film did not affect significantly the drying rate and rice quality. Considering the drying rate and quality, the optimum bed depth of mat paddy drying was around 6 cm.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.2
• /
• pp.226-232
• /
• 2002

In tradition, there have been two kinds of drying methods, which are sun drying and artificial drying. The sun drying method which has been adopted traditionally has been replaced by the hot-air drying method which is one of the most general methods of artificial drying, with its simple drying system, low initial cost of drying plant, and easy operating method. But the hot-air drying method has some defects ; (1)much energy loss happens due to the discharge of hot air during the drying process, (2)control of drying rate is not easy on account of changing relative humidity of inlet air for uniform hot air temperature, (3)high temperature of floods in drying process brings about the production of low-grade drying products. Also, the hot-air drying method is inducing environmental and sanitary problems which are resulting from the emission of high temperature and high humidity air, including stick on the drying progress. Vacuum drying technique, whose drying time and 7uantity of exhausting energy is about 1/3 ~1/4 of hot air drying, is very excellent in the drying efficiency. As the results, it took about 20 hours for material to reach about 18% of the final moisture content in order to store products for a long time, from about 470% of the early moisture content at the beginning of drying, and maximum drying rate comes to about $0.35 kg/m^2hr$ at about 350% of the moisture content.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.58-66
• /
• 2016

This study was performed to investigate drying characteristics and quality properties of dried persimmon with vacuum drying process. Drying characteristic curve of the dried persimmon showed that the constant rate drying period and falling rate drying period exist definitely. $_{\circ}Brix$, sugar content and hardness value of the dried persimmon increased as the vacuum pressure and heating temperature increased, but L value of the dried persimmon lower. The results indicated that the optimal conditions were at vacuum pressure of 40~50kPa abs., heating temperature of $30^{\circ}C$ and drying time of 3~4days.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.21 no.1
• /
• pp.64-69
• /
• 1992

To examine the effects of blanching treatments on the drying of hot red pepper, the pilot scale hot-air dryer equipped with the weight sensor using strain gauge type load cell and strain amplifier was designed and manufactured. The drying characteristic curves of cut hot red pepper showed a settling down period followed by a constant rate period and falling rate period, but blanched hot red pepper showed only falling rate period. According as the blanching time and temperature rises, the drying rates and the capsanthin contents of hot red pepper fairly increased. Considering the drying rates and the color values of dried hot red pepper, we suggest the desirable blanching condition of hot red pepper should be water blanching at $80^{\circ}C$ for 3 mins.