• Journal of the Korea Institute of Building Construction
• /
• v.14 no.4
• /
• pp.285-291
• /
• 2014

Partial replacement of cement with blast furnace slag has many advantages such as the reduction of construction fee, the decrease of hydration heat and the increase of long-term strength. Hence, slag is widely used in practice. This study investigates the effect of slag on the rheological properties of cement paste and mortar. Three different types of slag (BS1, BS2 and BS3) with five different contents (0, 20, 40, 60 and 80 wt.%) were used to replace the cement. Each type of slag has different fineness. Water to binder ratio was 0.5. Test results showed that the partial replacement of BS1 and BS2 decreased flow and increased O-lot flow time, whereas that of BS3 caused an opposite effect, i.e., increased flow and decreased O-lot flow time. It was found that there was a good corelation between the values of yield stress and flow.

• Korean Journal of Food Science and Technology
• /
• v.12 no.1
• /
• pp.18-23
• /
• 1980

Rheological behaviors of red pepper paste acre investigated with rotational viscometer at $25{\sim}55^{\circ}C$ and the following results were obtained. 1. At shear rate of $0.323{\sim}1.653\;sec^{-1}$, red pepper paste was found to be a thixotropic food product which showed pseudoplastic proper ties and also exhibited a yield stress and time dependent characteristics. 2. At a shear rate of 0.978 $sec^{-1}$, flow behavior index, consistency index and yield stress were 0.597, 192.3 dyne $sec^s/cm^{2}$, and 91 dyne/$cm^{2}$ respectively. 3. Variation of consistency of red pepper paste with time was found to be decayed by a second order kinetic equation and thereafter nearly time independent. 4. Variation of consistency of red pepper paste with temperature was found to follow Andrade's equation and the activation energy as calculated on the basis of this equation was $1.03\;kcal/g{\cdot}mole$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.5
• /
• pp.23-29
• /
• 2019

This study applies to the surface modification technique by coating the surface of aggregates using the modified paste such as cementitious materials in order to develop completely recycling technology of coarse aggregate. In this case, coating thickness of modified aggregate can be considered that the decision is dependent on the viscosity and tenacity of modified paste. In this study identify the flow properties of the fresh modified paste, and examined for the coating thickness of modified aggregate. As a result, it was possible to design a quantitative coating thickness of modified paste assuming that a modified paste to a Bingham Fluid and consider by excess paste theory and rheology constant (yield value). Accordingly, it is considered that the quantitative mix design of concrete using by surface modified aggregates will be possible.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.1
• /
• pp.21-28
• /
• 2008

Stress-strain curves based on Ramberg-Osgood and Hollomon relations are strongly dependent upon the regressed range of strain. This work investigates mathematical expressions of true stress-strain curves of metallic materials. We first observe the variation of yield strength, strain hardening exponent and stress-strain curve with regressed range of stain. Based on sectional regression and expression using one or two parameters, we propose an optimal strain range for which yield strength and nonlinear material behavior are quite appropriate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5654-5663
• /
• 2015

In the unsaturated soil, suction, the negative pore water pressure leads to increases of the yield stress and the plastic shear stiffness of the soil skeleton due to the growth in interparticle stress. Therefore, in this study, the stress-strain relationship based on cyclic elasto-plastic constitutive model extended for unsaturated soil considering the 1st and the 2nd yield functions was induced in order to account for these effects of suction under the dynamic loading condition such as the earthquake. Through the program code considering this relationship and the routine of the cyclic loading with the reversion of loading direction, the numerical simulation of the cyclic triaxial test under the unsaturated condition would be possible. It is expected that the results of this study possibly contribute to the accuracy improvement on the prediction of unsaturated soil behavior under the dynamic loading condition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.281-284
• /
• 2008

Performance evaluation exposing the performance of structure is affected by the material and structural characteristics. these should be necessary for the analysis about the effect of structure performance. Thus, to evaluate the structural performance affected the material properties and structural characteristics, firstly it is conducted the eigenvalues analysis and non-linear static analysis of the structure, secondly it is analyzed the performance influence factor of the structure. The performance influence factors affecting the performance of structure divided into five classes(strength of concrete, longitudinal and transverse reinforcement, aspect ratio, axial force). From the result of analysis about the change of performance influence factor, the more the strength of concrete is increasing, the more the maximum shear force is increasing and the yield displacement is not changed, the more longitudinal reinforce is increasing, the more yield displacement and the maximum basis shear force is increasing, the more the transverse reinforce is increasing, the change of maximum basis shear force is trivial. The yield displacement of structure is increasing and the maximum basis shear force is decreasing by increasing the aspect ratio, the more the axial force increases, the more yield displacement and maximum basis shear force decease.

• Nuclear Engineering and Technology
• /
• v.19 no.1
• /
• pp.22-33
• /
• 1987

The confirmed integrity of nuclear fuel cladding materials is an important object during steady state and transient operations at nuclear power plant. In this context, the clad material yielding behavior is especially important because of pellet-clad gap expansion. During the steep power excursion, the in-pile irradiation behavior differences between uranium-dioxide fuel pellet and zircaloy clad induce the contact pressure between them. If this pressure reaches the zircaloy clad yield pressure, the zircaloy clad will be plastically deformed. After the reactor power resumed to normal state, this plastic permanent expansion of clad tube give rise to the pellet-clad gap expansion. In this paper, the simple mandrel expansion test method which utilizes thermal expansion difference between copper mandrel and zircaloy tube was adopted to simulate this phenomenon. That is, copper mandrel which has approximately three times of thermal expansion coefficient of zircaloy-4 (PWR fuel cladding material) were used in this experiment at the temperature range from 400C to 700C. The measured plastic expansion of zircaloy outer radius and derived mathematical relations give the yield pressure, yield stress of zircaloy-4 clad at the various clad wall temperatures, the activation energy of zircaloy tube yielding, and pellet-clad gap expansion. The obtained results are in good agreement with previous experimental results. The mathematical analysis and simple test method prove to be a reliable and simple technique to assess the yielding behavior and gap expansion measurement between zircaloy-4 tube and uranium-dioxide fuel pellet under biaxial stress conditions.

• Fire Science and Engineering
• /
• v.21 no.3
• /
• pp.47-55
• /
• 2007

The mechanical properties such as 0.2% and 1% offset proof strength and elastic modulus are essential for a structural steel structure when the structure would be evaluated and designed to identify the performance of the structural stability exposed to fire condition. To obtain the mechanical properties for the structural steels at high temperature which are consisted of ordinary and marine ones, the tensile tests at various high temperatures had been conducted with two kinds of specimen of general structural steel SS 400 and welded steel SM 490 at the range of room temperature to $900^{\circ}C$ at interval of $100^{\circ}C$.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.557-560
• /
• 2009

본 연구에서는 건물의 규모, 용도 및 형식 등에 따라 다양하게 요구되는 성능에 대응할 수 있도록 하기 위한 성능설계에 대한 개념을 검증하고, 강구조 건축물의 특성을 고려한 성능레벨 및 성능한계에 대한 분류방법을 제안하였다. 또한 강구조 건축물의 경우 강도가 높고 경량인 특성에 의해 다른 구조형식에서는 크게 고려하지 않아도 되는 거주성능 및 진동특성을 제어하여 기능을 유지하기 위한 성능레벨을 설정하여 구조물이 항복하기 전의 성능레벨을 기능유지 및 무손상의 2단계로 제시하고, 이 때의 한계치를 기능한계 및 손상한계로 구분하였다. 강구조 건축물의 손상한계를 정의하기 위해 강구조 건축물의 설계 예를 이용하여 항복 층간변형각을 조사하였다. 그 결과 구조물의 손상발생을 억제할 수 있는 손상한계를 규정하기 위해 주로 사용하고 있는 층간변형각은 구조형식 및 설계방법에 따라 편차가 크게 나타나고 있으므로 손상한계치의 층간변형각을 임의로 설정하는 것은 매우 어려우며 향후 이에 대한 해석적, 실험적 검증이 필요할 것으로 판단되었다.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.40-41
• /
• 2006

본 논문은 수직형 트랜치 IGBT 구조에서 에미터를 트랜치로 형성하여 그 전기적인 특성을 MEDICI를 이용하여 고찰하였다. 제안한 구조의 항복전압과 온-상태 전압, 래치업 전류 그리고 턴-오프 시간이 기존 트랜치 IGBT에 비하여 향상되었음을 알 수 있었다. 항복전압은 트랜치 에미터에 의해 트랜치 게이트에 집중되는 전계를 완화시켜 일반적인 트랜치 IGBT보다 19%정도 향상되었으며 온-상태 전압과 래치업 전류는 각각 25%, 16% 정도 향상되었다. 하지만 제안된 구조의 턴-오프 시간은 무시할 수 있을 정도로 약간 증가하였음을 알 수 있었다.