• The Journal of Engineering Geology
• /
• v.29 no.3
• /
• pp.211-222
• /
• 2019

This study evaluates the yield load and allowable bearing capacity of ground in compressive loading tests to confirm the effect of CPR foundation reinforcement. The average compressive strength of the injection materials was higher than the planned compressive strength. Standard penetration tests for each stratum showed that foundation reinforcement improved the average N values, thereby increasing the bearing capacity of the ground. Compressive loading tests on two CPR piles revealed that the total and net settlement due to the maximum load exceed that permissible for the CPR pile diameter. The yield load and allowable bearing capacity calculated by the settlement criterion and the load-settlement curves varied greatly with the method applied. Therefore, it seems to be necessary to determine the optimum value through comprehensive analysis after applying various yield load calculation methods.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.33-42
• /
• 2004

Making use of SN steel in the building structure should be a prerequisite to adopt the design strength of said steel. As a preceding study, the material properties of STKN400B/490B tubes and SPAP235/325 and SPAR295 square pipes manufactured using SN400B/490B plates were evaluated. Compared with the yield and ultimate strengths of SN400B/490B plates, those of STKN400B/490B tubes increase. Nonetheless, the yield and ultimate strengths of STKN400B/490B tubes satisfied the design codes of STKN400B/490B tubes even though the tubes were fabricated via roll bending or press forming. On the other hand, the yield and ultimate strengths at the edges of SPAP235/325 square pipes did not satisfy the design codes based on the values at the sides. The maximum tensile and compressive residual stresses at the SN490B tube were equal to and 40% of the yield strength of the SN490B plate, respectively, In the case of the SPAP325 square pipe, both the maximum tensile and compressive residual stresses were 80% of the yield strength of the SN490B plate. The axial compressive loaded column test results snowed that the buckling strengths were not very different regardless of the mode of fabrication of STKN490B tunes. i.e., through roll bending or press forming. On the other hand, the buckling strength of the SPAP325 square pipe was higher than that of the built-up square pipe.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.145-148
• /
• 2008

AISC-LRFD, ACI 318 and Korean design specifications for concrete filled rectangular steel tube columns do not consider the increasing of axial stiffness such as the elastic modulus and the yield strength due to the confinement effect. AISC-LRFD and ACI 318, however, shows different basic philosophy and equations for computing the elastic modulus and the strength of CFT columns. Through this experimental study, nine rectangular CFT column specimens were made by varying thickness steel tube and concrete strength, the axial stiffness were compared. The comparison between the design specifications and the test results shows different values on the yield strength of the CFT columns. Even though, yield strength of the CFT columns are very similar between AISC-LRFD and Korean design specifications.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.5
• /
• pp.199-208
• /
• 2011

The purpose of this study is to evaluate of the strength and deformation capacity of metallic dampers with the variable slit shape. For this purpose, 12 metallic damper specimens were prepared and shear testing was performed. According to the test results, the S shaped metallic damper with the strut height of 200mm and angle of $60^{\circ}$ shows better hysteretic performance than any other specimens. By making a comparison between the yield strength in test and the proposed strength formula, test results shows larger yield strength than calculation method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.1
• /
• pp.21-28
• /
• 2008

Stress-strain curves based on Ramberg-Osgood and Hollomon relations are strongly dependent upon the regressed range of strain. This work investigates mathematical expressions of true stress-strain curves of metallic materials. We first observe the variation of yield strength, strain hardening exponent and stress-strain curve with regressed range of stain. Based on sectional regression and expression using one or two parameters, we propose an optimal strain range for which yield strength and nonlinear material behavior are quite appropriate.

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.181-183
• /
• 2016

In this work, the merged PiN Schottky(MPS) diodes based silicon carbide(SiC) have been optimized and designed for 1200V diodes by 2D-atlas simulation tool. We investigated the optimized characteristics of SiC MPS diodes such as breakdown voltage and specific on-resistance by varying the doping concentrations of P-Grid/epi-layer and space of P-Grid, which are the most important parameters. The breakdown voltage and specific on-resistance, based on Baliga's Figure Of Merit (BFOM), have been compared with and the SiC-based MPS diodes show improved BFOMs with low values of specific on-resistance and high breakdown voltage. It has been demonstrated 1,200 V SiC MPS diodes will find useful applications in high voltage energy-efficient devices.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.5 s.66
• /
• pp.561-570
• /
• 2003

This study evaluate the characteristics of stainless steel for the use of stainless steel tubes as structural members. The strength of stainless steel tube was compared with that of steel tube stub-columns through tensile experiment and compressed experiment. The selected experimental parameters were diameter (width)-thickness and section shape. The results of tests showed that stainless steel tubes could be predicted as superior to steel tubes in terms of tensile strength, yield ratio, elongation percentage, and absorption ability of energy. The yield strength of stainless steel tubes were found to be higher than the Korean Standards ($Fy=2.1tf/cm^2$) and the design strength of SIJ-ASD($Fy=2.4tf/cm^2$). It was also higher then the yield strength of steel tubes. The plastic deformation of stainless steel tubes was found to beto that of steel tubes.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.85-85
• /
• 2017

무동력 복합작업기는 치즐쟁기와 디스크의 배열에 따라 작업성능이 좌우된다. 프레임과 디스크, 치즐쟁기에 가해지는 기본적인 힘의 상태를 확인하기 위한 정적 구조해석을 수행하였다. 복합작업기는 디스크는 $18^{\circ}$가 경사진 형태로 전면9개 후면9로 총 18개, 치즐쟁기(Chiselplow)는 4개로, 디스크는 모두 18개이다. 정적인 상태에서 끄는 견인력은 100마력, 150마력, 200마력으로 하였으며 Inventor의 해석 시스템은 힘을 N으로 사용하기 때문에 각 마력에 부가되는 하중을 N으로 치환하여 사용하였다. 구속조건은 frame과, disc, chisel plow에 맞닿는 면을 구속하고, 힘의 방향은 프레임과 트랙터의 연결면, 디스크 날과 땅의 접촉면에 적용했다. front /rear 디스크는 이론상으로는 양 디스크가 쌍으로 마주하고 있어서 스캔데이타를 중심으로 모델링한 결과를 바탕으로, 전후면 디스크해로우의 해석을 수행하였다. 조립 또는 사용상의 문제점이나 자연적인 유격에 의해 어느 정도 대칭이 되지 않을수 있으나 그 정도에 따라 진동과 내구성에 문제가 될 수도 있기에 한쌍에 대해 모델링을 통한 해석을 수행하였다. 해석결과에 따르면 디스크에 작용하는 폰미세스 응력은 극한강도에 미치지 않은 것으로 나타났으며 Frame의 최대 폰 미세스 응력을 제외하면, 대부분의 응력은 항복강도에 현저히 미치지 못하는 수치이고, 프레임의 경우는 150마력, 200마력으로 힘을 가할 때 항복강도는 넘는 수치이지만 극한인장강도에는 미치지 못하는 수치인 것을 알 수 있었다. 100마력에 폰 미세스 응력의 최대값은 0.161918 MPa이고 프레임 강의 항복강도인 207MPa와 디스크의 항복강도인 250MPa에 못 미치는 수치이다. 150마력과 200마력의 힘으로 회전할 때의 폰 미세스 응력의 최대값은 0.286425MPa과 0.381921 MPa로 항복강도인 250MPa에 크게 못 미치는 수치이다. 그 이유는 디스크해로우 방식의 복합작업기는 견인저항력이 작게 설계되고 작업속도를 개선하기 위한 목적으로 사용되기 때문으로 사료된다. 벤치마킹 기대의 Rear 디스크도 마찬가지로 각도는 $18^{\circ}$이며, 동일한 구속조건을 적용하여 시뮬레이션을 수행하였으며 해석결과는 모두 항복강도 이내로 예측 되었다. 디스크에 최대로 응력이 미치는 부분은 디스크와 프레임이 연결되는 허브 부분이다. 각도가 커짐에 따라 응력이 증가하므로 이를 감안한 설계인자 도출이 가능하다. 마력과 각도가 증가함에 따라 디스크 해로우에 작용하는 폰미세스 응력과, 접촉압력이 증가하므로 이에 대한 검토와 동적하중인 로드프로파일을 적용한 해석을 수행하여 내구수명 특성에 대한 연구를 수행할 계획이다.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.11-20
• /
• 2004

This paper focused on square steel tubular column to H-beam connections (concrete filled tubular) with an outside-type diaphragm. Based on the yield line theory and the nonlinear static FEM analysis the specification equations were evaluated by comparing them with previous result of the simplified tensile experiment[please check. The yield line theory applied to the mechanical model theory revised by K. Morita, the nonlinear static FEM analysis using abaqus/standard, the ultimate strength equation in the specification equation using the factor for long-time loading, and the yield ratio according to material. The allowable strength in the specification equations applied the safety factors of 2.2 and 2.6 in the cases with and without filled concrete, respectively. Therefore, the evaluation of strength(for the previous result of the simplified tensile experiment in this study) was considered possible through the yield line theory, the nonlinear static FEM analysis, and the specification equations. Likewise, the specification equations were seen to be an underestimate of the previous result of the simplified tensile experiment. The strength and displaced mesh in the FEM analysis approximated the previous result of the simplified tensile experiment.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.9
• /
• pp.1253-1257
• /
• 2009

The effects of seven commercial gums (xanthan gum, guar gum, pectin, gum arabic, gellan, locust bean gum, and sodium alginate) at different concentrations (0, 0.3, and 0.6%) on flow properties of sweet potato starch (SPS) pastes were investigated. Flow behavior characteristics were adequately described by power law flow model, and yield stress was also measured by vane method. SPS-gum mixtures (5% w/w) at $25^{\circ}C$ were found to have high shear-thinning flow behavior with yield stress, and their consistency index (K) and apparent viscosity ($\eta_{a,100}$) increased with elevated gum concentration, except for pectin and sodium alginate. Vane yield stress ($\sigma_o$) value of SPS-pectin mixture was lower when compared to other mixtures while that of SPS-gellan mixture was much higher. Most of the gums, except for pectin, gum arabic, and sodium alginate, showed a synergistic effect on the elastic properties of SPS-gum mixtures. In general, the flow properties of SPS-gum mixtures appeared to be strongly influenced by the addition of gum, and dependent on the type and concentration of gum.