• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.11
• /
• pp.861-869
• /
• 2015

In this study, wall to bed heat transfer and hydrodynamic characteristics in a conical fluidized bed combustor was investigated using computational fluid dynamics method. A two-fluid Eulerian-Eulerian model was used with applying the kinetic theory for granular flow(KTGF). The effects of the two drag models, Gidaspow and the Syamlal-O'Brien model, different inlet velocities($1.4U_{mf}{\sim}4U_{mf}$) and different particle sizes on the hydrodynamics and heat transfer were studied. The results showed that the hydrodynamic characteristics such as bed expansion ratio and pressure drop were not affected significantly by the drag models. But the heat transfer coefficient was different for the two drag models, especially at lower gas inlet velocities and small particle sizes.

• Proceedings of the Korea Contents Association Conference
• /
• 2011.05a
• /
• pp.53-54
• /
• 2011

본 논문에서는 회전하며 이동하는 공에 작용하는 항력과 양력을 기반으로 비행 궤적 시뮬레이션 방법을 제시한다. 항력과 양력을 정확하게 계산하기 위해 필요한 양력 계수 모델, 표면의 거칠기에 따른 항력 계수 모델, 공기 밀도 모델 및 바람의 세기 모델을 제시하며, 이릍 통해 사실적이고 다양한 비행 시뮬레이션 결과를 보여준다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.7
• /
• pp.489-495
• /
• 2020

An accelerometer-based system was designed and constructed for drag measurement in a shock tunnel. Drag coefficient of a conical model was measured under a Mach 6 flow condition. A simple and intuitive calibration method was presented to compensate for the friction force of the drag measurement system, and the results of the measurement were compared with computational fluid dynamics in which the simple conical model was analyzed. The influence of drag measurement interference by supports of various shapes was identified and the design was presented to minimize. The drag coefficient measurement using the modified support showed that the error of the drag coefficient by the support was decreased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.8
• /
• pp.799-807
• /
• 2010

Direct numerical simulations (DNS) of turbulent channel flow for which the drag is reduced by using polymer additives have been performed by a pseudo-spectral method. The Reynolds number based on the friction velocity and half-channel height is 395, and the polymeric stresses due to the polymer additives are evaluated using the FENE-P (finitely extensible nonlinear elastic-Peterlin) model. The numerical results show that the drag reduction rate is significantly affected by the parameters used in the FENE-P model, such as the maximum extensibility and relaxation time of the polymer molecules. The turbulence data for both low- and high-drag reduction regimes are analyzed. In addition, the effects of FENE-P model parameters on the flow characteristics have been investigated for the same drag reduction rate due to the polymer additives. Finally, the present DNS results have been used to verify the correlation between rheological parameters and the extent of drag reduction, which was suggested by Li et al. (2006).

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.623-626
• /
• 2015

본 연구에서는 CFD 해석 프로그램 EDISON_CFD를 통하여 2차 세계 대전에 소련에서 제작한 복엽기 AN-2의 기체를 기본 모델로 하여 설제 기체에 사용된 TSAGI P-II-14 airfoil를 이용, 기본 모델의 상단 주익과 미익은 고정하고 하단 주 날개의 위치를 변화시켜 공력특성을 분석하였다. 익형의 평행배치의 경우 기본모델에 비해 양력은 적은 크기로 증가하나 항력이 급격히 증가하여 가장 양항비가 낮은 비효율적인 공력 해석 결과를 보였고 복염기 하단 주익의 돌출은 상단 주익의 돌출에 비해 미세한 양력 감소와 항력 증가를 보여 양항비가 감소하는 현상을 보였다. 상, 하단 주익의 상하 간격이 커질수록 양력은 중가, 항력은 감소하며 간격이 작아질수록 양력의 감소와 항력의 증가를 보였다. 본 연구 해석 결과에 따라 순항조건에서의 익형은 상,하 주익간 수직 간격을 넓게 배치하는 것이 가장 효율적으로 볼 수 있다.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.559-562
• /
• 2015

본 연구에서는 EDISON_CFD를 활용하여 승용차 모델을 단순화한 Ahmed Body의 후미 경사각 Slant angle $0^{\circ}$, $15^{\circ}$, $30^{\circ}$, $45^{\circ}$의 항력계수변화를 확인하였다. 결과 분석을 통해 Ahmed Body 후면의 후류와 항력계수의 변화 경향성이 같다는 것을 확인하였다. 항력계수는 자동차의 연비 및 최고속도 등 동력성능에 큰 영향을 미치므로 최저 항력계수를 찾아보았다. 각각의 경우에 EDISON_simulation 결과 값을 비교해보면 $15^{\circ}{\sim}30^{\circ}$ 사이에서 최저 항력계수를 갖는 것을 확인할 수 있었다. 정확한 값을 찾기 위해 Polynomial Curve Fitting을 사용하여 Slant angle 이 $22.91^{\circ}$일 때 최저항력계수 0.1375를 갖는 것을 확인하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.527-528
• /
• 2012

DBD (Dielectric Barrier Discharge) plasma actuator was designed for aerodynamic drag reduction using plasma flow control, and the drag reduction was measured by wind-tunnel tests using 2D test model. At the zero wind velocity, the plasma flow control had no effect on the drag reduction because the flow separation and surface friction drag were not occurred. At the wind velocity of 2m/s, 9.7% of drag was reduced by the flow separation control. The drag reduction decreased as the wind velocity increased.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.1
• /
• pp.23-32
• /
• 2016

Various studies have been conducted for drag reduction of a high-speed vehicle by injecting counterflow jet from its nose cone. In this study, in order to obtain baseline data and key parameters for drag reduction method, the counterflow jet study of the USA is reviewed and summarized. The nose cone shapes of each study are hemisphere cylinder, truncated cone, and reentry capsule, and their test conditions are summarized accordingly. Key parameters for drag reduction are jet mach number, mass flow rate, and pressure ratio. Even though drag reduction effects show various results according to given test conditions, it is found that the drag reduction effect reaches up to 40~50%.

• 한국항공운항학회:학술대회논문집
• /
• 2015.11a
• /
• pp.35-38
• /
• 2015

본 연구에서는 스포츠급 경항공기 모형의 공력 특성을 공군사관학교 아음속 풍동에서 측정하였다. 풍동시험은 유속 40m/s에서 이전 모델과 최근 공력성능 향상을 위해 보완된 모델에 대해 비교 실험 수행하였으며, 정확한 데이터를 얻기 위하여 흐름각 효과, 벽면효과, 지지대 간섭효과를 보정하여 공력계수를 산출하였다. 실험 결과, 두 모델의 항력계수와 양력계수가 전체적으로 유사한 경향성을 보이나 고받음각에서의 양력특성의 차이가 발생하였다. 또한 실제 비행 시의 레이놀즈 수 유동을 모사하기 위하여 Trip strip의 영향에 대하여 실험하였다. 그 결과 Trip strip을 부착하였을 경우 항력계수가 증가하고 최소항력받음각이 낮아지는 결과를 획득하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.6
• /
• pp.614-619
• /
• 2015

In this study, a dynamics model was developed to predict the motion performance of an Autonomous Underwater Vehicle (AUV). The dynamics model includes basic dynamic state variables of the hull and force terms to determine the motion of the AUV. The affecting terms for the forces are hydrostatic force, added mass, hydrodynamic damping, lift and drag forces. The force terms can be calculated using analytical and Computational Fluid Dynamics methods. For the underwater motion simulation, a simple PD controller was used. Also, the AUV was tested in a water tank and near sea for the partial verification of the fluid drag force coefficients and way-point tracking motions.