• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.2
• /
• pp.92-100
• /
• 2016

Reliability analysis of tripod support structure for offshore wind turbine was performed. Extreme distribution function of peak response due to wind and wave loads was estimated by applying peak over threshold(POT) method. Then, stress based limit state function was defined by using maximum stress of support structure which was obtained by multiplying beam stress and concentration factor. The reliability analysis result was compared when maximum stress was calculated from shell element. Reliability index was evaluated using first order reliability method(FORM).

• Journal of the Korean Society for Railway
• /
• v.14 no.1
• /
• pp.39-48
• /
• 2011

The paper describes four practical cases of railway structure concerning a three-dimensional numerical approach to analyse dynamic soil-structure interaction(SSI)of railway tracks on layered soil under transient load in the time domain. The SSI-Model has been implemented in TDAPIII accounting for nonlinear properties of the track and soil. The approach can be also be used to calculate vibration propagation in the soil and its effect on nearby buildings and structure. The Method is applied to analyse the dynamic response of railway tracks due to a moving wheel set. Finally some sample are given in order to reduce the vibration at the point of emission, at the transmission path and the structure itself.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.642-647
• /
• 2007

Determination of loading conditions for tube hydroforming(THF) process that implies an amount of the increment in axial feeding and internal pressure for each step is one of the most important constituents at the process design level. On account of the fact that those design factors mentioned above are imposed simultaneously during the process, suitable loading conditions are required to obtain robust products without any failure such as buckling, necking, bursting and so on. In which, especially, bursting is well known as the most frequently occurred failure in general THF process. In this study, therefore, determination of the loading condition based on the adaptive method was carried out to obtain safe loading paths. In addition, forming limit curves are applied to evaluate the derived loading conditions by using the simulation results. Consequently, it is found that described method in this study for THF process design is useful and has a feasibility.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.34.1-34.1
• /
• 2010

TLS(Terrestrial Laser Scanning)는 레이저를 이용하여 물체의 3차원 위치 정보를 원격으로 획득할 수 있는 시스템이다. 그러나 TLS로부터 획득한 3차원 위치 정보는 처짐 또는 응력 평가 등에 있어서 구조 정보로서 사용하기에는 한계가 있다. 따라서 정밀한 형상정보의 획득을 위해서는 3차원 형상 좌표 정보에 대한 적절한 데이터 처리가 필요하다. 본 연구에서는 구조물에 작용하는 하중 또는 지점 조건에 대한 정보 없이 회기분석의 중첩을 이용하여 TLS로부터 얻은 대상물의 이산화 된 위치 정보로 부터 구조물의 정밀한 변형 형상을 추정할 수 있는 방법을 제시한다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.16 no.3
• /
• pp.43-50
• /
• 2012

The FEMA P695 document proposed a methodology to evaluate the collapse safety of a structure and the validity of the seismic design coefficients. In this study, the seismic performance of six- and twelve-story staggered wall structures with a middle corridor was evaluated based on the FEMA P695 procedure. The analysis results of the prototype structures were compared with those of the structures with an increased coupling beam depth or an increased re-bar ratio of the coupling beams in order to investigate the effect of retrofit. The adjusted collapse margin ratios (ACMR) of the model structures obtained from incremental dynamic analyses turned out to be larger than the specified limit states of an ACMR of 20%, which implies that the analysis model structures have enough strength against design level earthquakes. It was also observed that the increase in the re-bar ratio of the coupling beams between the staggered walls was more effective in increasing the ACMR than an increase in the depth of the coupling beams.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.6
• /
• pp.523-535
• /
• 2014

According to the capacity design concept underlying current steel seimsic provisions, the braces in concentrically braced frames should dissipate seismic energy through cyclic tension yielding and compression buckling. On the other hand, the beams and the columns in the braced bay should remain elastic for gravity load actions and additional column axial forces resulting from the brace buckling and yielding. However, due to the difficulty in accumulating the yielding and buckling-induced column forces from different stories, empirical and often conservative approaches have been used in design practice. Recently a totally different approach was proposed by Cho, Lee, and Kim (2011) for the prediction of column axial forces in inverted V-braced frames by explicitly considering brace buckling. The idea proposed in their study is extended to X-braced seismic frames which have structural member configurations and load transfer mechanism different from those of inverted V-braced frames. Especially, a more efficient rule is proposed in combining multi-mode effects on the column axial forces by using the modal-mass based weighting factor. The four methods proposed in this study are evaluated based on extensive inelastic dynamic analysis results.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.92-101
• /
• 2020

It is necessary to develop a rational method for evaluating the safety of bridges for the passage of inseparable crane vehicles exceeding the limit weight. In this study, the same method applied to the development of the recently introduced reliability-based highway bridge design code - limit state design method is applied to the calibration of the live load factor for the crane vehicle. Structural analysis was performed on the concrete bridge and the required strengths of the previous design code, the current design code and AASHTO LRFD were compared. When comparing the unfactored live load effect, the live load of the crane was greater than that of the current and previous design code. When comparing the required strength by applying the calibrated live load factor, the previous design code demands the largest strength and the current design code and the crane live load effect yields similar value. The results of safety evaluation of the actual bridges on the candidate route for the crane passage secured the same reliability as the target reliability index required by the design code and the strength of the cross section of the actual bridge is calculated greater than the required strength for the passage of the crane, which confirms the safety for the passage of the crane.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.102-113
• /
• 2017

A new index for the buckling strength of non-structured plates is proposed. The external work or the deformation energy caused by the external loads or the boundary displacement controled by a load parameter is calculated along an equilibrium path of the member under consideration. If the second variation of the energy with respect to the parameter loses its positiveness, it defined as the limit of the stability. In contrast to the current method given in codes where the stability limit is evaluated by using only representative internal forces, the evaluation of the stability limit is always consistent even with the change of the distribution of the internal forces on the boundary. If the elasticity is concerned, the result from this proposed approach becomes identical to that from the classical methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.190-190
• /
• 2003

동력 전달용 구동부품에 있어서 중공 플랜지 형상의 부품은 흔히 찾아 볼 수 있으며, 이는 높은 강도를 요구하기 때문에 강도향상을 위하여 단조에 의한 제품의 성형 방법이 많이 연구되고 있다. 중공 플랜지형상을 갖는 제품의 제조 방법으로서는 중실 플랜지 형상으로 단조하여 내경부를 절삭가공하는 방법, 중실 소재를 후방압출하여 중공 플랜지형상으로 단조하는 방법, 또는 중공의 초기소재를 사용하여 중공 플랜지형상으로 단조하는 방법이 일반적이다. 본 연구에서는 Fig. 1에 나타낸 것과 같이 중공 플랜지 형상을 갖는 기계 부품의 단조방법에 대해 연구하였으며, 중공 관의 내경을 $d^1$, 외경을 $d^2$, 플랜지부의 외경을 $D^0$, 중공 관의 두께를 t, 플랜지부의 두께를 T로 정의하였다. 중공 플랜지 형상에 있어서 공정 설계의 변수는 다양하겠으나, 본 연구에서는 중공관의 외경과 내경의 형상비 $\alpha$(=$d^2$/$d^1$), 플랜지의 폭과 중공관의 두께비 $\beta$(=B/t) 및 중공관의 두께와 플랜지의 두께비 r(=T/t)의 변화에 따른 성형조건에 관해 고찰하였다. 중공 플랜지 형상의 성형방법으로 Fig. 2에 나타낸 것과 같은 $\circled1$중실소재를 이용한 후방압출단조(backward extrusion forging)방법, $\circled2$중공 소재를 이용한 엎셋(upset forging)방법, $\circled3$중공 소재를 이용한 압조법(injection forging), $\circled4$중실소재를 이용한 압조-압출(injection-extruding forging)법의 4가지의 단조 방법을 제시 하였다. 또한, 유한요소해석을 수행하여 소성유동 형태, 유효변형률, 단조하중을 검토하고. 모델재료인 납을 이용한 실험을 통하여 이를 검증하였다. 이를 바탕으로 산업 현장에서 경험에 의존하였던 공정 설계를 보다 효과적으로 개선하기 위한 단조법을 제시하고자 하였다. 또한 중실 소재를 이용한 중공 플랜지 형상의 단조 방법 중 보다 적절한 단조방법인 압조 단조에 있어서 일반적으로 사용되고 있는 SM10C에 대한 유한요소 해석을 수행하였으며, 제품의 형상비에 따라 폴딩 결함의 발생 유무를 검토하고, 폴딩 결함 없이 단조하기 위한 중공 플랜지의 형상한계 비를 제시하였다.

• Journal of Welding and Joining
• /
• v.13 no.2
• /
• pp.96-105
• /
• 1995

A modified method for the analysis of short fatigue crack growth has been presented, and calculations based upon the modified method are compared with experimental results for S45C carbon steel. It is also shown that the modified method is in good agreement with experimental data. The proposed equation for the fatigue crack growth rates includes a material constant which relates the threshold level to the endurance limit, a correction for elastic-plastic behaviour and a means for dealing with the effects of crack closure. In this study one of the modifications is to substitute the Forman' s elastic expression of the stress intensity factor range into the geometrical factor The other is a consideration of the bending effect which is developed from the moment caused by the eccentric cross sectional geometry as the crack grows. Thus, this method is useful for residual life prediction of the mechanical structures as well as the welding structures.