• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.349-349
• /
• 2010

전달 경로 해석 기법은 NVH 문제 해결 프로세스에서 자주 사용되는 기법으로서 소음원 X 전달 경로= 응답 모델을 사용한 접근방식입니다. 수음(응답)점에서 문제의 진동 및 소음 응답을 고체 및 공기 음원이 응답에 미치는 기여도 또는 개별 경로, 모드, 판넬 기여도의 합으로 세분화하여 표시함으로써, 문제의 원인을 규명하고, 문제 해결 및 대책 방안에 대한 통찰력을 제시하며, NVH 문제의 해결을 위해 사용되는 필수적인 도구입니다. 본 강좌에서는 건물에 설치되는 설비의 작동 시 고체 음원 평가 및 철도 소음의 공기음과 구조음 기여도 평가를 위해 적용된 전달 경로 해석 기법 사례를 소개할 것입니다. 설비 작동시의 전달 경로 해석 기법에 의해 평가된 고체 음원의 신뢰성 확보를 위하여 $\bullet$ 직접 측정된 하중 데이터와 역행렬 기법에 의해 예측된 하중 비교 및 $\bullet$ 가진 햄머로 가진시의 가진력과 측정된 가속도 신호를 사용하여 역행렬 기법으로 계산된 하중의 비교를 수행하였습니다. 철도 소음의 공기음 및 고체음 기여도 평가를 위해서는 $\bullet$ 열차 주행중 철로에서 측정된 가속도를 사용하여 철로면에 가해지는 하중을 역행렬 기법으로 계산하였으며 $\bullet$ 철로 주변에서 거리별 측정된 소음중, 고체음의 기여도 파악을 위해서, 전달 경로 해석기법으로 예측된 고체음과 측정된 소음을 비교하였습니다.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.251-260
• /
• 2001

It is required to evaluate the axial strain of reinforced concrete beams in order to predict the ductility of reinforced concrete beams subjected to reversed cyclic loading. A model was proposed to determine the axial strains In reinforced concrete beams by analysing the behavior of reinforced concrete sections and comparing with published test results. The proposed axial strain model inclusively reflected four kinds of paths : Path 1-steel bar in an elastic stage or a unloading region; Path 2-after flexural yielding; Path 3-a slip region; and Path 4-a reversing loading region. The equations to predict the axial strains of each path were proposed. The proposed equations took into account the effects of the loading program. Comparison of axial strains between experimental results and the results from proposed equations showed to be in a good agreement with experimental results.

• Journal of the Korean Society for Railway
• /
• v.14 no.1
• /
• pp.49-56
• /
• 2011

In this paper, it was compared the characteristics of the stress and settlement that occur from a track on the ground using a model test and has quantitatively analyzed the difference based on stress path and effect of the rotation of principal stress. Under identical roadbed conditions, the settlement generated by moving wheel loads were found to be 6 times and 3 times larger than that from static loads and cyclic loads, respectively. The deviator stress affecting shear deformation and the length of stress path generated by moving loads were twofold or greater increase than those by static loads. Furthermore, the stress path generated by moving loads was approached more closely to Mohr-Coulomb failure criteria compared to that by static loads. Also, it was found that ballasted track was occurred about 60% of maximum stress at $40^{\circ}$ of the rotation angle of principal stress and was affected with rotation of principal stress with moving wheel loading condition.

• Journal of the Korean Ceramic Society
• /
• v.28 no.1
• /
• pp.19-19
• /
• 1991

Fracture of Al2O3 tubes for different loading path under combined tension/torsion was investigated. Macroscopic directions of crack propagation agreed well with the maximum principal stress criterion, independent of the loading path. However, fracture strength from the proportional loading test(τ/σ= constant) showed either strengthening or weakening compared to that from uniaxial tension, depending on the ratio τ/σ. The Weibull theory was capable to predict the strengthening of fracture strength in pure torsion, but not the weakening in the proportional loading condition. The strengthening or weakening of fracture strength in the proportional loading condition was explained by the effect of shear stresses in the plane of randomly oriented microdefects. Finally, a new empirical fracture criterion was proposed. This criterion is based on a mixed mode fracture criterion and experimental data for fracture of Al2O3 tubes under combined tension/torsion. The proposed fracture criterion agreed well with experimental data for both macroscopic directions of crack propagation and fracture strengths.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.2
• /
• pp.67-76
• /
• 1992

A procedure to determine the axle load limits of asphalt concrete pavements are proposed in this study. Axle load limits are determined by calculating maximum tensile strains at the bottom of the asphalt stabilized base layer and maximum vertical strains at the top of the subgrade. In order to investigate the efficiency of axle configuration, calculated influence line of wheel load on domestic expressway pavement system is used. Limiting strains are selected through the analysis of conventional failure criteria. From the analysis of axle load limits about axle composition(single-axle, tandem-axle, tridem-axle), it is found that the axle load limits of tandem-axle and tridem-axle can be calculated by muitipling the axle load limits of single-axle by axle numbers and that axle load limits are closely related to the thickness of each layer of pavement structure. It is also found that the axle load limits by tensile strains are more critical than those by vertical strains on asphalt concrete pavement models of YOUNG-DONG, KYONG-IN and KYONG-BU expressways.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1190-1193
• /
• 2010

본 연구에서는 점토층의 자중압밀을 시행하여 현장강도를 구현하기 위하여 1/70로 축소 모델링하여 원심모형실험을 수행하였으며, 점토구간에 PBD 타설시의 연약지반의 압밀침하거동을 분석하기 위하여서는 1/100로 축소모델링하여 원심모형실험과 전산해석을 실시하였다. 전산해석결과 성토체중심아래의 점토지반의 침하량은 1단계 성토제방하중 하에서 4.8개월 경과 후 최대 침하량은 41.1cm, 2단계 성토하중에서 4.2개월 경과 후의 최대침하량은 78.8, 3단계 성토하중에서 6개월 경과후의 침하량은 93.5cm의 침하가 발생하는 것으로 나타나 수치해석 결과와 원심모형실험결과 값의 유사한 경향을 확인하였다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.979-984
• /
• 2008

This paper discusses how to use basic strut-and-tie models(STM) for practical application. Construction of STM starts with drawing of load paths with equilibrium conditions. Understanding of structural systems including form active systems, vector active systems, and section active systems help us select appropriate systems for possible STM. Simple circular fans can be employed for load paths from concentrated forces to distributed forces. Strength of struts depends on configuration of their nodal zones which meet tension ties and effective compressive strength. The effective compressive strength of struts are assumed to be mainly influenced by transverse strain.

• Geotechnical Engineering
• /
• v.10 no.1
• /
• pp.7-18
• /
• 1994

A new model for describing the behavior of clay under monotonic and cyclic loading is proposed. This model uses the hyperbolic representation for the stress -strain relationship in overconsolidated state and it describes undrained effective stress path on the basis of the critical state theory. The developed constitutive model by using an energy dissipation equation can describe the behavior of clay in heavily overconsolidated state as u.ell as lightly overconsolidated state under monotonic loading. In order to extend the model for the behavior of clay under cyclic loading, a shift function of undrained stress spacing ratio is introduced in the constitutive model developed for monotonlc loading. A single additional parameter is required to represent the cyclic effect and it can be reasonably deter mined from the test results. The measured behavior in undrained cyclic triaxial tests has been easily and precisely predicted by the newly developed constitutive model.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.11a
• /
• pp.429-434
• /
• 2000

본 연구에서는 등분포하중을 받는 laminated 박판의 거동해석을 제시하였다. 접착한 두 박판의 비선형 지배방정식을 Von Karman 식을 이용하여 유도하고 박판의 거동을 차분법을 이용하여 수치해석 한다. Interlayer에서의 전단변형을 고려하여 지배방정식에 포함시켜 하중 증분법(load incremental method)으로 기하학 비선형 해석을 수행한다. 하중 증분법에 따른 반복법을 도입하여 비선형 방정식을 해석했다. 해석방법의 타당성을 입증하기 위하여 해석결과들을 기존의 문헌의 결과와 비교, 검토함으로써 본 논문에서 제시한 이론 및 해석방법의 타당성을 입증한다. 차분법의 하중 증분법 알고리즘을 개발하여 예제문제에 대한 수치해석 결과들을 논하였다.(중략)

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.2
• /
• pp.21-28
• /
• 1987

The paper describes the analysis of large displacement problems including instability phenomena. The element used in this is a degenerated isoparametric shell element with eight nodes. Total Lagrangian formulation has been adopted in this study using Newton-Raphson iteration method with incremental load. The linear stability analyses performed usually for the initial position can be repeated at several advanced fundamental states on the non-linear buckling path. Thus a current estimate of the failure load is given. The numerical examples of a cylindrical panel under uniform load, simply supported plate under axial load, and clamped plate under uniform load are carried out. The examples applying degenerated isoparametric elements to bifurcation buckling and nonlinear collapse problems are also performed.