• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.452-458
• /
• 2022

Three types of gas-liquid hybrid horizontal, vertical and needle-to-cylinder plasma reactors were fabricated. Through these reactors, a high-efficiency, eco-friendly cleaning concept that generates reactive active species generated in atmospheric plasma discharge and gas-liquid activation reaction of cleaning components through the potential difference within the electrode was presented. As a result of comparing the efficiency for cleaning performance, the needle-to-cylinder type reactor had the best characteristics. Through this study, it was confirmed that the gas-liquid hybrid atmospheric pressure plasma reactor has the potential to be applied to ultra-precision cleaning processes such as semiconductor processes.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.5
• /
• pp.542-548
• /
• 2005

A fluidized bed reactor containing porous media has been known to be effective for nitrogen and organic matters removal in wastewater. The porous media which attached microbes plays important roles in simultaneous nitrification/denitrification (SND) due to coexistence of oxic, anaerobic and anoxic zone. For SND reaction, oxygen and organic substrates should be effectively diffused from wastewater into the intra-carrier zone. However, the overgrowth heterotrophic microbes at the surface of porous media may restrict from substrates diffusion. From these viewpoints, the existence and effect of heterotrophic bacteria at surface of porous media might be the key point for nitrogen removal. A porous media-membrane hybrid process was found to have improved nitrogen removal efficiency, due to stimulated denitrification as well as nitrification. Microelectrode studies revealed that although intra-media denitrification rate in a conventional fluidized bed was limited by organic carbon, this limitation was reduced in the hybrid process, resulting in the increased denitrification rate from 0.5 to $4.2\; mgNO_3-N/L/hr$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.57.1-57.1
• /
• 2010

레이저 색소 분자간의 회합을 막음으로써 높은 레이저 효율을 갖는 고체 색소 레이저를 제조하기 위해 레이저 색소인 DCM을 유-무기 하이브리드 재료에 화학적으로 결합시켰다. 수산화기를 기능기로 갖는 DCM을 합성하여 이를 솔-젤반응의 전구체로 활용하였다. 유기실란을 DCM과 함께 솔-젤반응을 시킴으로써 DCM이 결합된 유무기 하이브리드 재료를 제조하였다. DCM이 결합된 유-무기 하이브리드 재료는 유기물과 무기물의 특성을 각각 갖고 있기 때문에 용액공정을 통해 고체 색소 레이저를 단시간에 제작할 수가 있을 뿐만 아니라 열적 및 광학적으로 우수한 특성을 보여주었다. Nd:YAG 레이저를 여기광으로 이용하여 DCM이 결합된 유-무기 하이브리드 재료의 레이저 효율을 측정하여 DCM을 유기용매에 녹인 색소 레이저의 레이저 효율과 비교하였다. DCM이 결합된 유-무기 하이브리드 재료는 DCM의 농도가 높아질 수록 유기용매를 이용한 색소 레이저에 비해서 더 높은 레이저 효율을 가지는 것을 관찰하였다. 이는 DCM이 결합된 유-무기 하이브리드 재료에 각각의 DCM 분자가 실록산 망목구조와 화학적으로 결합이 되어있기 때문에 하이브리드 재료에 안정적으로 존재할 수 있게 되고 망목구조에 둘러쌓여 분자간의 회합이 방지되는 효과를 가지게 되기 때문이다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.202-205
• /
• 2010

Auto ignition of hybrid rocket using $N_2O$ catalytic decomposition was studied in the present study. The hybrid rocket consists of catalytic igniter, solid fuel, combustor, and nozzle. The Ru/$Al_2O_3$ catalyst for $N_2O$ decomposition was synthesized by an impregnation method, and $N_2O$ conversion as reaction temperatures was measured. The temperature change of the catalytic ignitor was measured at the operating condition, and the possibility for the auto ignition of hybrid rocket was validated.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.497-502
• /
• 2014

The conversion reaction of methane and carbon dioxide at an atmospheric pressure plasma reactor filled with Ni-$Al_2O_3$ and Ni-$MgAl_2O_4$ catalyst was performed. Effects of various process parameters such as the applied electric power, reaction gas flow rate, reactor temperature, mixing ratio of reactants and the presence of the catalyst on the reaction between methane and carbon dioxide were analyzed. From the analysis of the contribution of the catalyst in the reaction step, even if the temperature raised to $400^{\circ}C$, there was no spontaneous catalytic conversion of methane and carbon dioxide without plasma discharges. When the catalysts for the conversion of methane and carbon dioxide would be adopted to the plasma reactor, the careful selection of suitable catalysts and process parameters should be essential.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.3
• /
• pp.287-293
• /
• 2010

In this study, the toluene gas in VOCs was removed using bioreactor which applied with hollow fiber membrane and Pseudomonas sp. TDB-4. The EBRT of each reactor are controlled 60 sec(R-1) and 30 sec(R-2) and inlet tolune concentration of both R-1 and R-2 is controlled from 25ppm to 500 ppm. Up to 500 ppm of toluene concentration, the toluene removal efficiency of R-1 and R-2 are 92% and 81%, and theirs removal capacities are about 100 g/$m^3$/hr and 180 g/$m^3$/hr, respectively. In addition, according to this study, toluene removal efficiencies at the hollow fiber are approximately 70%(60 sec) and 45%(30sec).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.11
• /
• pp.20-25
• /
• 2007

In this paper, It was reported the dielectric constant in organic inorganic hybrid silica material such as SiOC film modeling of bond structure by annealing in organic properties. The organic inorganic hybrid silica material were deposited using bis-trimethylsilymethane (BTMSM, [(CH3)3Si]2CH2) and oxygen gas precursor by a plasma chemical vapor deposition (CVD). The organic inorganic hybrid silica material have three types according to the deposition condition. The dielectric constant of the films were performed MIS(Al/Si-O-C film/p-Si) structure. The C 1s spectra in organin inorganic silica materials with the flow rate ratio of O2/BTMSM=1.5 was organometallic carbon with the peak 282.9 eV by XPS. It means that organometallic carbon component is the cross-link bonding structure with good stability. The dielectric constant was the lowest at annealed films with cross-link bonding structure.

• Clean Technology
• /
• v.26 no.1
• /
• pp.65-71
• /
• 2020

Various solar hybrid energy conversion processes, which have both the advantages of renewable energy sources and fossil energy sources, have been developed in the world because stable and predictable energy supplies, such as electricity and natural gas, are necessary for modern societies. In particular, a solar hybrid energy conversion process based on a dual fluidized bed process concept has been expected as the promising solution for sustainable energy supply via thermochemical conversions, such as pyrolysis, combustion, gasification, and so on, because solar thermal energy could be captured and stored in fluidized bed materials. Therefore, the attrition and heat transfer characteristics of silicon carbide and alumina particles used for fluidized bed materials for the solar hybrid energy conversion process were studied in an ASTM D5757 reactor and a bubbling fluidized bed reactor with 0.14m diameter and 2m height. These characteristics of novel fluidized bed materials were compared with those of sand particles which have widely been used as a fluidized bed material in various commercial fluidized bed reactors. The attrition resistances of silicon carbide and alumina particles were higher than those of sand particles while the average values of heat transfer coefficient in the bubbling fluidized bed reactor were in the range of 125 ~ 152 W m^-2K^-1.

• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.89-94
• /
• 2011

DeNOx characteristics of hybrid SNCR-SCR process have been investigated in a pilot scale flow reactor. DeNOx efficiency of SNCR reaction was about 80% at $970^{\circ}C$ and hybrid SNCR-SCR process showed 92% at $940^{\circ}C$ with NSR = 2.0. Compared to SNCR process alone, hybrid SNCR-SCR process was more effective at cool side, which is lower than $940{^{\circ}C}$. It should be also noted that ammonia slip from hybrid SNCR-SCR process was below 1ppm at the condition of higher space velocity and the required catalyst volume can be decreased to 2/3 of SCR process. Key factors for DeNOx efficiency of hybrid SNCR-SCR process were found to be $NH_3$ concentration and NOx selectivity of urea injected in SNCR process.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.78-88
• /
• 2005

The combustion characteristics of End-Burning hybrid combustor using different types of injector system are numerically investigated to visualize the temperature fields in the combustion chamber The basic characteristics of combustion with different O/F ratio is also analyzed in order to capture the main behavior of diffusion flame inside the swirl induced hybrid combustion chamber It was found that the arrangement of oxidizer injectors give strong effect on the temperature field dominating mixing between fuel and oxidizer. The results show that among five different oxidizer injectors arrangement, the counter flow injector has the highest mixing efficiency. However, the observed high wall temperature presence near the oxidizer injectors remains to be solved.