• Journal of the Korea Society of Computer and Information
• /
• 제14권1호
• /
• pp.117-125
• /
• 2009

In hybrid wireless networks, a mobile node in MANET can communicate with other mobile nodes as well as nodes in the Internet. Hybrid mobile networks help to expand the application domains of MANET from limited areas, such as military applications to more diverse and general application areas. Previous routing protocols in hybrid wireless networks have not taken advantage of location information of nodes in a network. By using location information of nodes, a routing protocol can reduce the overhead of control messages for efficient network operations. This paper proposes a routing protocol for hybrid mobile networks, called Location-aided AODV+ (LAp) that is based on ADOV+ and takes advantage of node's location information. Performance evaluation shows that LAp performs better than ADOV+ when there are a sufficient number of nodes in a network for route establishments.

• Journal of the Korea Concrete Institute
• /
• 제22권3호
• /
• pp.325-333
• /
• 2010

In this study, new moment-resisting precast concrete beam-column joint made up of hybrid steel concrete was developed and tested. This beam-column joint is proposed for use in moderate seismic regions. It has square hollow tubular section in concrete column and connecting plate in precast U-beam. The steel elements in column and beam members were connected using bolt. Furthermore, in order to prevent the premature failure of concrete in hybrid steel-concrete connection, ECC(engineered cementitious composite) was used. An experimental study was carried out investigating the joint behavior subjected to reversed cyclic loading and constant axial compressive load. Two precast beam-column joint specimens and monolithic reinforced concrete joint specimen were tested. The variables for interior joints were cast-in-situ concrete area and transverse reinforcement within the joint. Tests were carried out under displacement controlled reverse cyclic load with a constant axial load. Joint performance is evaluated on the basis of connection strength, stiffness, energy dissipation, and displacement capacity. The test results showed that significant differences in structural behavior between the two types of connection because of different bonding characteristics between steel and concrete; steel and ECC. The proposed joint detail can induce to move the plastic hinge out of the ECC and steel plate. And proposed precast connection showed better performance than the monolithic connection by providing sufficient moment-resisting behavior suitable for applications in moderate seismic regions.

• The Journal of Korean Academy of Prosthodontics
• /
• 제51권3호
• /
• pp.183-189
• /
• 2013

Purpose: The aim of this study was to evaluate clinical outcomes of implant supported fixed-hybrid prostheses (FHP) in the fully edentulous arches. Materials and methods: Patients in this retrospective study were restored with fixed-hybrid prostheses supported by 4 to 6 implants and functioned more than 1 year of loading. Outcome measures were marginal bone change of implant related with sex, anatomical location (maxilla vs. mandible), opposing teeth, loading time of patients, tilting of posterior implant by Mann- Whitney U test and cantilever length of superstructure by regression analysis, and complication rates. Significance level was set P<.05. Results: A total number of 84 implants (16 restorations) placed in 16 patients were observed for 28 months and mean marginal bone loss was $0.53{\pm}0.39mm$. There were no differences of marginal bone loss according to sex, anatomical location (maxilla vs. mandible), opposing teeth, loading time of patients (P>.05), and cantilever length was not significantly related with a marginal bone loss of implant next to cantilever (P>.05). Complication was shown in 11 patients and veneer fracture and dislodging of artificial teeth were most prevalent. Conclusion: Within the limitations of this study, although marginal bone loss of FHP was very little, complication rates were high. Irrespective of tilting of most posterior implants, marginal bone loss of most posterior implants next to cantilever was less than those of the other implants positioned anteriorly. Cantilever length (<17 mm) did not affect a marginal bone loss of most posterior implants.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.252-252
• /
• 2016

최근 학계나 산업계에서 indium tin oxide (ITO)의 높은 전기 전도도 및 광투과율을 이용하여 줄 발열을 기초로 하는 투명 면상 발열체에 대한 연구가 활발히 진행 되고 있다. 하지만 단일 ITO 박막으로 제작한 투명 면상 발열체는 온도가 상승함에 따라 균일하게 발열 되지 않으며, 글라스의 곡면 부분에서 유연성이 부족하여 크랙이 발생하는 다양한 문제점들을 가지고 있다. 이를 해결하기 위해 ITO의 결정화 온도 $160^{\circ}C$ 이상의 고온공정 또는 증착 후 열처리가 필요 하는 추가적인 공정이 필요하다. 따라서 본 연구에서는 단일 ITO 박막의 단점을 개선하는 ITO/Ag/ITO 하이브리드 구조의 투명 면상 발열체를 제작하여 전기적, 광학적 특성을 비교하고 발열량, 온도 균일성, 발열 유지 안정도를 조사하였다. 본 연구에서는 $50{\times}50mm$ 크기의 non-alkali glass (Corning E-2000) 기판 상에 마그네트론 스퍼터링 공정으로 상온에서 ITO/Ag/ITO 박막을 연속적으로 증착 하여 다층구조의 하이브리드 형 투명 면상 발열체를 제조하였다. 박막 증착 파워는 DC (Ag) power 100 W, RF (ITO) power 200 W로 하였으며 ITO박막두께는 40 nm로 고정 시키고 Ag박막 두께는 10 ~ 20 nm로 변화를 주었다. 증착원은 3인치 ITO 단일 타깃(SnO2, 10 wt.%)과 Ag 금속 타깃 (순도 99.99%)을 사용하였으며, 고순도 Ar을 이용하여 방전하였으며 총 주입량은 20 sccm, working pressure는 1.0 Pa을 유지하였다. 증착전 타깃 표면의 불순물 제거와 방전의 안정성을 유지하기 위해 10분간 pre-sputtering을 진행하고 증착하였다. 증착한 박막의 전기적, 광학적 특성은 각각 Hall-effect measurements system (ECOPIA, HMS3000), UV-Vis spectrophotometer (UV-1800, SHIMADZU)으로 측정하였으며, 하이브리드 표면의 구조 및 형상은 field emission-scanning electron microscopy (FE-SEM, Hitachi S-4800)으로 관찰하였다. 또한 투명 면상 발열체의 성능은 0.5 ~ 3 V/cm의 다양한 전압을 power supply (Keithly 2400, USA)를 통해서 시편 양 끝단에 인가한 후 시간에 따른 투명면상 발열체의 표면 온도변화를 infrared thermal imager (IR camera, Nikon)를 이용하여 관찰하였다. 하이브리드 구조를 가진 ITO박막의 두께는 40 nm로 고정 시키고 Ag박막의 두께는 10, 15, 20 nm로 변화를 주었다. 이들 박막의 면저항 값은 각각 5.3, 3.2, $2.1{\Omega}/{\Box}$였으며, 투과도는 각각 86.9, 81.7, 66.5 %였다. 이에 비해 두께 95 nm의 단일 ITO박막의 면저항 값은 $59.5{\Omega}/{\Box}$였으며, 투과도는 89.1 %였다. 하이브리드 구조의 전기적특성은 금속층의 두께가 증가할수록 캐리어 농도 값이 증가함에 따라 비저항 값이 감소되어 면저항 값도 감소된 것이며, 금속 삽입층의 전도특성이 비저항에 큰 영향을 주고 있음을 보여준다. 하지만 금속 층의 두께가 증가할수록 Ag층이 연속적인 막을 형성하여 반사율이 증가함에 따라 투과도가 감소하였다. 따라서 하이브리드 구조를 가진 투명 면상 발열체에 금속 삽입층의 두께 조절은 매우 중요한 인자임을 확인 할 수 있었다. 또한 발열성능을 평가 하기 위해 시편 양 끝단에 3 V전압을 인가한 결과, 금속 삽입층의 두께가 10 nm에서 5 nm씩 증가한 하이브리드 구조를 가진 투명면상 발열체의 최고 온도는 각각 98, 150, $167^{\circ}C$ 였으며, 단일 ITO의 최고 온도는 $32^{\circ}C$였다. 이 것은 동일한 두께 (95 nm)의 단일 ITO 박막과 비교하여 면저항이 낮은 하이브리드 박막의 발열량은 약 $120^{\circ}C$로 발열효율이 매우 우수한 것을 확인 할 수 있었다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제44권11호
• /
• pp.20-25
• /
• 2007

In this paper, It was reported the dielectric constant in organic inorganic hybrid silica material such as SiOC film modeling of bond structure by annealing in organic properties. The organic inorganic hybrid silica material were deposited using bis-trimethylsilymethane (BTMSM, [(CH3)3Si]2CH2) and oxygen gas precursor by a plasma chemical vapor deposition (CVD). The organic inorganic hybrid silica material have three types according to the deposition condition. The dielectric constant of the films were performed MIS(Al/Si-O-C film/p-Si) structure. The C 1s spectra in organin inorganic silica materials with the flow rate ratio of O2/BTMSM=1.5 was organometallic carbon with the peak 282.9 eV by XPS. It means that organometallic carbon component is the cross-link bonding structure with good stability. The dielectric constant was the lowest at annealed films with cross-link bonding structure.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제23권4호
• /
• pp.914-925
• /
• 1998

This paper considers the evaluation of the hybrid acquistion perdformance for the pilot signal in the direct sequence code division multiple access(DS/CDMA) forward link. the hybrid acquisition is introduced by the combination of two schemes, the parallel and serial acquisions. The mean acquisition time of the proposed scheme is derived to consider both the best case(the correct code-phase offsets are included i one subset) and the worst case(the correct code-phase offsets exist at the boundary of two subsets), which are cause by the distribution of the correct code-phase offsets in the subset. Expressions for the detection, false alarm, and miss probabilities are derived for the case of multiple correct code-phase offsets and multipath Rayleigh fading channel. Numerical results present the hybrid acquistion performance with repect to design parameters such as postdetectio integration length in the search and verification modes, subset size, and number of I/Q noncoherent correlators, and compare the hybrid acquistion with the parallel acquistion in terms of the minimum acquistion time under the same hardware complexity.

• Journal of the Korea Concrete Institute
• /
• 제26권6호
• /
• pp.771-778
• /
• 2014

This paper concerns the flexural behavior of hybrid steel fiber-reinforced ultra high performance concrete (UHPC) beams. It presents experimental research results of hybrid steel fiber-reinforced UHPC with steel fiber content of 1.5% by volume and steel reinforcement ratio of less than 0.02. This study aims at providing realistic information about UHPC beams in bending in order to establish a reasonable prediction model for flexural resistance in structural code in the future. The experimental results show that hybrid steel fiber-reinforced UHPC is in favor of cracking resistance and ductility of beams. The ductility indices range through 9.2 to 15.2, which means high ductility of UHPC. Also, the flexural capacity of beam which contains stirrups in pure bending zone is similar to that of beam which does not contain stirrups in pure bending zone. This result represents that the flexural capacity is not affected by the presence of stirrups whose spacing is 150 mm in bending zone.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제14권3호
• /
• pp.1459-1466
• /
• 2013

Recently, various types of three-dimensional cameras have been used to analyze surrounding environments. In this paper, we suggest a mechanism of adaptively switching active and passive cameras of hybrid cameras, which can extract 3D image information more accurately. The suggested method first obtains brightness and texture features representing the environment from input images. It then adaptively selects active and passive cameras by generating rules that reflect the extracted features. In experimental results, we show that a hybrid 3D camera consisting of passive and active cameras is set up and the proposed method can effectively choose appropriate cameras in the hybrid camera and make it possible to extract three dimensional information more accurately.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제15권5호
• /
• pp.3139-3145
• /
• 2014

This paper describes the design of a size-reduced ring hybrid coupler for microwave band using an artificial dielectric substrate(ADS). ADS structure adopts the second substrate on which has lots of the metalized via-holes. The effective capacitance and effective dielectric constant per unit length of ADS increases compared to the normal substrate due to the via-holes. This enables the physical length of microstrip transmission line to be reduced by adopting ADS instead of the normal substrate. In order to present an example of size-reduction of microwave wireless circuit by ADS, a size-reduced 3GHz ring hybrid coupler is designed, fabricated and measured in this work. The designed coupler has the smaller size from the normal one by 65% due to the ADS, while no critical degradation from ideal performances is observed. The measured power division ratio at two output ports are -3.05dB and -3.135dB, respectively. In addition, the phase differences are 3o for in-phase division and 176o for out of phase split. The measured performances are so similar to ideal ones, and prove the design of size-reduced ring hybrid coupler using ADS is successful.

• Journal of Intelligence and Information Systems
• /
• 제19권1호
• /
• pp.1-17
• /
• 2013

In this article, several types of hybrid forecasting models are suggested. In particular, hybrid models using the generalized additive model (GAM) are newly suggested as an alternative to those using neural networks (NN). The prediction performances of various hybrid and non-hybrid models are evaluated using simulated time series data. Five different types of seasonal time series data related to an additive or multiplicative trend are generated over different levels of noise, and applied to the forecasting evaluation. For the simulated data with only seasonality, the autoregressive (AR) model and the hybrid AR-AR model performed equivalently very well. On the other hand, if the time series data employed a trend, the SARIMA model and some hybrid SARIMA models equivalently outperformed the others. In the comparison of GAMs and NNs, regarding the seasonal additive trend data, the SARIMA-GAM evenly performed well across the full range of noise variation, whereas the SARIMA-NN showed good performance only when the noise level was trivial.