• International Journal of Highway Engineering
• /
• v.8 no.1 s.27
• /
• pp.89-98
• /
• 2006

The weight-to-power ratio of the standard truck for the climbing lane design is known to be 200lb/hp. The value was known to be assumed based on constant trucks' capability and regional distributions in stead of widely varied distributions region by region. Additionally, this value was assumed after investigating registered vehicles' statistics instead of investigating real portions of truck volumes. Therefore, it may be said that the value of the current standard truck does not reflect regional or industrial diversity and proportions of truck volumes. To resolve these issues, the present paper studies diversified standard trucks which consider regionally or industrially diversified and observed-volume based weigh-to-power ratios. For this purpose, individual trucks' weigh-to-power ratios obtained at toll-gates of national expressways were used. For regionally based study, the whole nation are divided into 8 regions, then each region is characterized by a unit of a weigh-to-power ratio. The applicability of each value is provided. Results show that the single value for the nationwide standard truck may be 208 lb/hp, 8 lb/hp higher than the current value of 200 lb/hp. Results also show that regional values ranged widely from 170 lb/hp to 230 lb, 30 lb/hp higher/lower than the current value. Conclusively, regional diversity of trucks' weigh-to-power ratios was identified then three types of standardized weigh-to-power ratios which may represent regional characteristics were suggested. As the diversified standard truck are applied to the design standard, two benefits are expected such as decrease of rear-end accident rates or decrease of climb lane construction costs.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.139-149
• /
• 2019

For retaining wall designs, horizontal earth pressure induced by traffic loads over the walls is calculated based on equivalent uniform pressure height. The AASHTO LRFD design standards propose equivalent uniform pressure height of traffic loads; however, the equivalent uniform pressure height is calibrated using the US standard trucks. As the domestic standard trucks are different from the US standard trucks, in this study, new domestic equivalent uniform pressure height is proposed using the Boussinesq theory varying vehicle directions, Poisson's ratios of pavement layers, and retaining wall height. The proposed equivalent uniform pressure heights are generally higher than those proposed by the AASHTO design standards because the axle loads and their densities of two domestic standard trucks are higher than those of the US standard trucks. The most highest equivalent uniform pressure height was found for traffic direction perpendicular to longitudinal direction of retaining wall.

• Journal of Korean Society of Transportation
• /
• v.32 no.5
• /
• pp.473-486
• /
• 2014

This study aims to review whether climbing lane installment is needed by analyzing the impact that standard trucks have on traffic according to vertical alignment at SMART highway, and if climbing lanes are required to propose truck speed change curves based on slope length. We used VISSIM simulation model to obtain the speed change of the standard truck on uphill roads. The standard truck on climbing lanes was set for 100kg/kW (170lb/hp) with the entry speeds set and analyzed by 90, 100, and 110 km/h considering the future speed limit of trucks. The results of the research show that under SMART highway circumstance, the 1 and 2% vertical alignment is not needed at the climbing lane but 3% vertical alignment is necessary. In order to install the climbing lane at 3% vertical alignment, the speed change curve of truck depending on slope length of 90, 100, and 110km/h of entry speed is proposed.

• Tunnel and Underground Space
• /
• v.32 no.5
• /
• pp.327-343
• /
• 2022

The standard work report for trucks was developed that records data on truck haulage operations in open-pit and underground mines, and to evaluate the performance of haulage operations. Work reports used in 5 mines in Korea was secured and analyzed, and items to be included in the standard work report were determined. By analyzing the formulas for key performance indicators (KPIs) proposed by the Global Mining Guidelines Group (GMG), it was possible to determine how to record time-related data. After selecting a limestone underground mine as a research area, the performance of haulage operations was evaluated using a standard work report. As a result, in terms of truck availability, uptime was 46.7%, and both physical and mechanical availability were 100%. In the case of utilization, use of availability was 88.2%, the asset utilization was 41.1%, and operating and effective utilization were 88.2% and 79.2%, respectively. Also, in terms of efficiency, operating efficiency was found to be 89.9%.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.75-85
• /
• 2019

The lateral load from traffic depends on standard truck's axle loads and locations, loading distance from the inner wall. The method of limit state design has been adopted and used for design of roads in the Republic of Korea since 2015. The concept of equivalent height of soil accounting for traffic loading is often used for design of retaining walls to quantify the traffic loads transmitted to the inner wall faces. Due to the different characteristics of the standard design trucks between Korea and US (AASHTO), the direct use of the guidelines from AASHTO LRFD leads to incorrect estimation of traffic load effects on retaining walls. This paper presents the results of evaluation of equivalent height of soil to reflect the standard truck of the nation, based on the findings from analytical solutions using 3D finite element method. Compare to US, the standard truck loading has a structure where the axle load is concentrated so that the equivalent load height is estimated to be slightly larger than AASHTO for lower retaining wall height. It would be reasonable to present the equivalent load height in Korea more conservatively than AASHTO in terms of securing long term stability of the retaining wall structure.

• Journal of Korean Society of Transportation
• /
• v.24 no.5 s.91
• /
• pp.35-44
• /
• 2006

Acceleration and deceleration curves have been used for design purposes worldwide. The curve in design level has been regarded as an single deterministic curve to be used for design of climb lanes. It should be noted that the curve was originally made using ideal driving truck and that the curve is applied during design based on the assumption of no difference between ideal and real driving conditions. However. observations show that aged vehicles and lazy behavioring drivers nay make lower performance of vehicles than the ideal performance. The present paper provides the results of truck speeds at climbing lanes then probabilistic variation of acceleration and deceleration corves. For these purposes. a study about identification of vehicle makers, and weights for trucks at freeway toll gates and then observation of vehicle-following speed were performed. The 85%ile results obtained were compared with the deterministic performance curves of 180, 200, and 220 Ib/hp. It was identified that the performance of 85%ile results obtained from vehicle-following-speed observations were lower than one from deterministic performance curves. From these results, it may be concluded that at the beginning Point of climbing lanes additional $16.19{\sim}67.94m$ is necessary and that at the end point of climbing lanes $53.12{\sim}103.24m$ of extension is necessary.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.4
• /
• pp.119-128
• /
• 2018

Limit state design has been implemented in Korea since 2015; however, there exists no specification of lateral load determination on retaining wall due to the Korean standard traffic load on retaining wall's backfill surface. The lateral load from traffic depends on lane number, standard truck's axle loads and locations, loading distance from the inner wall. The concept of equivalent height of soil accounting for traffic loadings is typically used for design of retaining walls to quantify the traffic loads transmitted to the inner wall faces. Due to the different characteristics of the standard design trucks between Korea and US (AASHTO), the direct use of the guidelines from AASHTO LRFD leads to incorrect estimation of traffic load effects on retaining walls. This paper presents the results of evaluation of equivalent height of soil to reflect the Korean standard truck, based on the findings from analytical solutions using Bounessq's theory and numerical assessment using 2D finite element method. Consequently, it was found that the equivalent heights of soil from the Korean standard truck load were lower for lower retaining wall height.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.6
• /
• pp.50-60
• /
• 2013

Dynamic response of steel plate girder bridges by KL-510 design truck in KHBDC considering the road surface roughness of bridges and bridge-vehicle interaction is investigated. Simply supported steel plate girder bridges with span length of 20m, 30m, and 40m from "Standard Highway Bridge Superstructure" published by the Korean Ministry of Construction are used for a bridge model, and ten sets of the road surface roughness of bridge deck are generated from power spectral density (PSD) function by assuming the roadway as "Average Road". A three dimensionally modeled 5-axle tractor-trailer with its gross weight, which is the same as that of KL-510 design truck, is used for dynamic analysis. For the finite element modeling of superstructure, beam element for the main girder, shell element for the concrete deck, and rigid link between main girder and concrete deck are used. Impact factor and DLA of steel plate girder bridges for different span are calculated by the proposed numerical analysis model and compared with those specified by several bridge codes.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1D
• /
• pp.67-72
• /
• 2008

Heavy equipment is a very important factor for successful construction implementation. Also, the cost for heavy equipment is a major part of construction cost. Therefore, the estimation of equipment cost is a critical job in the construction planning phase. A formula for production rates shown in 'Standard Unit Labor' has been used to estimate construction equipment capability per hour and cost. Although the performance of equipment has been improved, the efficiency rates in the formula are not updated lately. Therefore, this research performed several site visits to measure construction equipment working time and then calculates the efficiency rates for hydraulic backhoe, loader, and dump truck. The results show that the measured efficiencies of backhoe and loader are higher than current ones and vice versa for dump truck. This research proposes the needs for a standardized calculation formula and systematic and long-term data collection and measurement for updating efficiency rates for heavy equipment.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.455-464
• /
• 2013

If North Korea continuously remains an isolated nation without social interaction with South Korea, the gaps in the theoretical and technological status in construction technology become greater between North and South Korea. Therefore if interactions between North and South Korea can be made, there will be significant improvement in infrastructure technological performance can be made(i.e., Reinforced Concrete bridges). This study was performed to compare and analyze data related to the design standards of North Korean RC bridges and to execute a structural analysis based on standard design specifications of RC slab bridges. Especially, basic study of analyzing the influences on design truck loads of North and South Korea was conducted for the purpose of predicting the performance of North Korean RC slab bridges and the safety levels of traveling vehicles in advance. It is expected that the results of this study can be used as fundamental data for the set-up of South-North RC bridge specification when South and North Korea enter a stage of cooperation and interaction between South and North Korea are actively pursued to prepare for reunification.