• Korean Journal of Metals and Materials
• /
• v.50 no.1
• /
• pp.8-12
• /
• 2012

This study aims to analyze the formability property of surface texturing processed automotive steel sheet for improving the sheet forming property. In the paper, the effect of cavities fabricated using the laser surface texturing technique on automotive high strength steel sheets was studied. The frictional behavior of the sheet drawing is a function of interface parameters such as sheet surface roughness, holding force, contact pressure, etc. For these reasons, automotive steel researchers want to optimize the surface topography of automotive steel sheets in order to enhance the formability. Therefore, this study presents the behavior of deformation of a laser surface texturing steel sheet by considering the frictional operation during the deep drawing process.

• Transactions of Materials Processing
• /
• v.33 no.4
• /
• pp.291-300
• /
• 2024

To compare the lubrication performance improvement of different laser texturing surface treatment patterns, ring-shaped specimens were prepared by processing line and dot patterns using a fiber laser device. Ring compression tests were conducted to compare the reduction rates of the inner diameter corresponding to the same height reduction of the specimens. Laser processing conditions were set to create patterns with a depth of 9㎛ and a width of 45㎛. Ring specimens were processed with varying spacings between dots and lines. The forging lubricant TECTYL FORM CF 351S was uniformly applied to the upper and lower compression tools, and the rings were compressed by 40% using a hydraulic press, after which the inner diameter was measured. The comparison of inner diameter reduction rates indicated that pattern processing improves lubrication performance, with line patterns being more effective than dot patterns in enhancing lubrication performance.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.299-299
• /
• 2014

엔진블럭 사이를 왕복 운동하는 피스톤은 엔진블럭과의 마찰은 불가피한 상태일 수밖에 없으며 이렇게 된다면 엔진블럭 또는 피스톤의 파손, 변경이 있을 수밖에 없다. 피스톤에 대한 연구는 이러한 파손, 변경을 최소화시키기 위해서 내마모성, 내열성 그리고 내구성을 향상시키는데 목적을 두고 있다. 본 실험은 APS법으로 제작된 자기윤활복합코팅층을 준비해 레이저표면텍스처링을 넣어 마찰 실험을 하였다. 기지재로는 알루미나-지르코니아복합체를 사용하였고, 고체윤활제로는 $CaF_2$ 및 $BaF_2$을 사용하였다.

• The Journal of the Korea Contents Association
• /
• v.10 no.1
• /
• pp.1-9
• /
• 2010

In this paper we present a shading technique for realistic rendering of the surfaces with irregular and complex textures using a single photograph. So far, most works have been using many photographs or special photographing equipment to render the surfaces with irregular and complex textures as well as dividing texture regions manually. We present an automatic selection method of the region segmentation techniques according to properties of materials. As our technique produces a reflectance model and the approximated Bidirectional Reflection Distribution Function(BRDF) parameters, it allows the recovery of the photometric properties of diffuse, specular, isotropic or anisotropic textured objects. Also it make it possible to present several synthetic images with novel lighting conditions and views.

• Composites Research
• /
• v.34 no.4
• /
• pp.264-268
• /
• 2021

In this study, we propose a method for fabricating hydrophobic coatings/films with three-dimensional (3D) hierarchical nanostructured organic/inorganic composite surfaces. An epoxy-based, large-area 3D ordered nanoporous template is first prepared through an advanced photolithography technique called Proximity-field nanoPatterning (PnP). Then, a hierarchically structured surface is generated by densely impregnating the template with silica nanoparticles with an average diameter of 22 nm through dip coating. Due to the coexisting micro- and nano-scale roughness on the surface, the fabricated composite film exhibits a higher contact angle (>137 degrees) for water droplets compared to the reference samples. Therefore, it is expected that the materials and processes developed through this study can be used in various ways in the traditional coating/film field.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.130.2-130.2
• /
• 2011

본 연구에서는 RF magnetron sputtering을 이용하여 실리콘 박막 태양전지용 ZnO:Al 전면전극을 제작하고 다양한 식각조건에 따른 ZnO:Al 박막의 표면형상 변화와 함께 전기적 및 광학적 특성 변화를 조사하였다. pin 구조를 갖는 실리콘 박막 태양전지의 효율 향상을 위해서는 입사광의 산란효과에 따른 광포획 증가가 필수적이며 이를 위하여 ZnO:Al 전면전극의 표면텍스처링 형성이 필요하다. 식각용액으로는 HCl과 HF 등을 사용하였으며 식각용액 농도 및 식각시간을 변화시켰다. 식각 후의 ZnO:Al 박막의 표면형상은 SEM(Scanning Electron Microscope)과 AFM(Atomic Force Microscope)을 이용하여 분석을 하였고, UV-visible-nIR spectrometer를 이용하여 총 투과도 및 산란 투과도를 측정하였다. 이 외에도 four-point probe 및 Hall measurement를 이용하여 전기적 특성 변화를 조사하였다. 다양한 식각조건에 따라 제조된 ZnO:Al 박막 위에 실리콘 박막 태양전지를 제작하여 전면전극의 표면형상에 따른 태양전지 성능변화를 비교 분석하였다.

• Tribology and Lubricants
• /
• v.26 no.6
• /
• pp.311-316
• /
• 2010

Surface texturing of micro dimple or pore-shaped pattern was prepared using a fiber laser system. Surface texturing was designed to have a square pattern with a particular pitch distance for each corresponding density of 5, 10, 20, and 30%. Thermal damages such as bulges and burrs formed during laser irradiation were observed around the dimples. Thermal damages were later removed by lapping using alumina particles of $0.3{\mu}m$ in diameter. Oscillating friction tests were performed against heat-treated high speed steels under lubricated condition. The lubricant used was SAE 5W-30 automotive engine oil. Normal contact pressure and oscillating frequency was 0.28 MPa and 20 Hz, respectively. The tests were continued for 20 minutes, and friction plots were recorded for examination. Results revealed that the coefficient of friction was lowered regardless of texturing density. Moreover, the lowest coefficient of friction was obtained for 10% density texturing. It is attributed to increased lubricity due to the introduction of surface texturing. In addition, it is concluded that the optimum texturing density and pattern must be found for the best lubricity and low friction.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.364-364
• /
• 2009

The solar cell is in the spotlight as a future green energy source. In the solar cells based on silicon wafer, the improvement of efficiency is one of crucial issues. One of techniques for high efficiency is texturing on the surface of solar cells. We studied the laser texturing on the surface of multi-crystalline silicon solar cells. The laser texturing followed by chemical etching is adequate for the multi-crystalline structure which have random crystallographic directions. We used the fiber laser for texturing and the SiNx as a masking layer for etching process. We investigated the shapes of holes for texturing in the various laser power conditions and analyzed the holes after removal of thermal damages caused by laser ablation through a 3D profiler.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.349-349
• /
• 2009

High quality ZnO:Al films were prepared on glass substrates by in-line RF magnetron sputtering and their surface morphologies were modified by wet-etching process in dilute acid solution to improve optical properties for application to silicon thin film solar cells as front electrode. The as-deposited films show a strong preferred orientation in [001] direction under our experimental conditions. A low resistivity below $5{\times}10^{-4}{\Omega}{\cdot}cm$ and high optical transmittance above 80% in a visible range are achieved in the films deposited at optimized conditions. After wet-etching, the surface morphologies of the films are changed dramatically depending on the deposition conditions, especially working pressure. The optical properties such as total/diffuse transmittance, haze and angular resolved distribution of light are varied significantly with the surface morphology feature, whereas the electrical properties are seldom changed. The cell performances of silicon thin film solar cells fabricated on the textured films are also evaluated in detail with comparison of commercial $SnO_2$:F films.

• Laser Solutions
• /
• v.15 no.3
• /
• pp.1-6
• /
• 2012

The friction force of patterned needle in elastomer have been investigated to verify the application for bio and plastic industry. The micro pattern on the needle surface were prepared by 266 nm, 20 ns laser and 800 nm, 220 fs laser, which were able to generate the different surface roughness. The friction force was measured by the load cell of 10 N capacity. As the results, the friction force of no patterned needle is almost constant during the needle penetrates the silicone rubber sample. However, the needle having asperities shows the variation of the friction force. The higher the surface roughness is, the smaller the friction force is until the surface roughness is very high. In our experiment conditions, the reduction of the friction force by 20 % compared to no pattern needle was achieved with straight and $50{\mu}m$ discrete line generated by 266 nm, 20 ns laser.