• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.3
• /
• pp.370-374
• /
• 2003

Cell cracking method using a non-collision was evaluated for the possibility of new red ginseng grinding technique. Based on particle size distribution analysis by 1size shaker, the ratios of 100 mesh penetrated particles were 94.9% for hammer mill (group A) and 95.6% for cell crack (group B). The ratio of 120 mesh penetrated particle of group A was higher than that in group B. The particle size distributions for 100 mesh non-penetrated Powder between 2 groups were not significantly different, and particle size distribution analysis by laser scattering analyzer showed that the particle size ranges were 0.77~128.07 ${\mu}{\textrm}{m}$ for group A and 4.24~180.07 ${\mu}{\textrm}{m}$ for group B. The Particle size distribution in group A was more broad than that in group B. The mean particle size in group B was larger than that in group A, while the standard deviation of particle size distribution in group B was less than that in group A. Structural surface characteristics, in group A, particle size distribution was broad and the distribution curve was amorphous. The structure of individual particles was similar to unequal stone which was roughly grinded and had soft cotton-like surface. In the contrary, in group B, particle size distribution was relatively narrow and also individual size particles were ubiquitously distributed. The structure of individual particles was unequal cut stone shape.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.7
• /
• pp.343-352
• /
• 2016

Effects of grinding time and chemicals dosage in arsenic removal from contaminated paddy soil in China were investigated using lab scale attrition and froth flotation combining process. Arsenic concentration in the field soil was 76.51 mg/kg, exceeding Korean and Chinese standards, and predominant arsenic compounds fraction in sequential extraction was "residual" (over 80%). After wet sieving, soil with >2 mm and < 0.038 mm showed concentration lower than 'Warning Level' in Korea. Soil with 0.038-0.075 mm, showing the highest concentration, was discarded since it occupied minor weight fraction (10.1%). Thus soil between 0.075 and 2 mm was only used in the combining process. The highest Arsenic concentration in progeny fragments smaller than 0.038 mm reached up to 981.66 mg/kg after 5 min of attrition. Optimal dosage of collector ($C_5H_{11}OCS_2K$) and modifier ($Na_2S$ and $CuSO_4$) in froth flotation process for the selective separation of the chipped progeny particles from the parent fragments were determined both as 200 g/ton. Arsenic removal efficiency in froth flotation process was 38.47% and it was increased to 72.74% in additional flotation process, scavenging. Average arsenic concentration after overall process - wet sieving, attrition and froth flotation - was estimated to 16.45 mg/kg.

• Resources Recycling
• /
• v.28 no.3
• /
• pp.26-34
• /
• 2019

Due to the increasing demand of rare earth magnet for various application, it is predicted that the amount of waste rare earth magnet will increase sharply. The process of waste rare earth magnet recycling is mainly consisted of leaching and separation of rare earth element contained in the magnet. However, there is no study on the breakage characteristics of the waste rare earth magnet for production of magnet powder. Therefore, in this study, effective crushing/grinding process and breakage characteristics were investigated for waste rare earth magnet. In the case of jaw crusher, the particle size of magnet was effectively reduced without rapid oxidation. In ball mill grinding test, it was found that the grinding process was not performed properly at the early stage of grinding. Moreover, waste rare earth magnet showed very low specific rate of breakage(S) and high fraction of fine particle breakage distribution(B) compared to ordinary minerals. These results can be used as a basic data for developing crushing/grinding circuit of waste rare earth magnet.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.1
• /
• pp.25-30
• /
• 2005

수소 분위기에서 10wt.%MnO와 기계적인 분쇄(반응성 기계적 분쇄)에 의해 Mg의 수소 저장 성질을 향상시켰다. 회전 속도는 250 rpm, 밀링시간은 2 h, 그리고 시료 대 볼 중량비는 1/45이었다. 준비한 Mg-10wt.%MnO 시료는 활성화를 위한 수소화물 형성 분해 싸이클링이 필요없었으며, 첫 번째 싸이클 593k 12 bar $H_2$에서, 10분 동안에 3.12wt.%, 60분 동안에 3.95wt.%의 수소를 흡수하였다. 또한 Mg-10wt.%MnO는 593k 0.8 bar $H_2$에서 60분 동안에 2.12wt.%의 수소를 방출하였다. MnO와 Mg의 방응성 분쇄는, 핵생성을 용이케하고 (Mg 입자의 표면에 결함 형성과 첨가물에 의해), Mg 입자의 표면에 crack을 만들어 Mg의 입자 크기를 줄여 그 결과 수소 원자의 확산 거리를 작게 함으로써 수소 흡수 방출 속도를 증가시킨다. 수소화물 형성 분해 싸이클링은 Mg 입자의 표면에 crack을 만들고 Mg의 입자 크기를 줄여 수소 흡수 방출 속도를 증가시킨다.

• Applied Chemistry for Engineering
• /
• v.22 no.2
• /
• pp.133-137
• /
• 2011

In this study, illite was size-reduced using a wet-ball-milling treatment to improve its dispersion. Changes in illite particle size, size distribution, and dispersion characteristics after varying the treatment period were investigated. And the dispersion and dispersion stability of illite solution after 2 h wet ball milling treatment with different pH conditions were also evaluated. The illite particle size significantly decreased as the treatment time increased and the size reduction effect of wet ball milling deteriorated above 2 h treatment time. In addition, illite particle size was more evenly distributed as the treatment time increased. X-ray diffraction (XRD) analysis showed that no crystal structural changes of illite were induced, but the characteristic peak of illite the weaker due to the size reduction and exfoliation, as the treatment time increased. Zeta potential analysis showed that the illite dispersion improved, as the treatment time increased. The illite wet-ball-mill treated at pH 2 had the lowest dispersion stability. Illite dispersion and dispersion stability increased as pH increased, due to the increase in surface ionization. Hence, the results showed that as the treatment time increased, the illite particle size decreased, and dispersion and dispersion stability improved due to the increase in surface energy and repulsion force between particles.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.685-691
• /
• 2013

Ibuprofen, non-steroidal anti-inflammatory drugs; NSAIDs, is a highly crystalline substance with the pharmaceutical properties of poor solubility and low bioavailability. The size reduction of ibuprofen is needed to improve the solubility. The objective of this study is to optimize the grinding condition of ibuprofen. Grinding of ibuprofen was carried out using a planetary mill. Grinding parameters were optimized using Box-Behnken experimental design method. The physical characteristics of ground ibuprofen were investigated for the particle size by particle size analyzer, for the crystal size by X-ray diffraction (XRD), and for the tensile strength by tensile/compression tester. The optimum conditions for the milling of ibuprofen were 290 rpm of the revolution number of mill, 24.6 g of the weight of sample, and 10 minutes of grinding time. The measured value of the particle size of ground ibuprofen at these optimum conditions was $13.5{\mu}m$. The results showed that the crystal size of ibuprofen was reduced by the planetary milling process. In case the relative density of the tablets formulated of ground ibuprofen was range of 0.85~0.90, the tensile strength of them was range of 1$2{\sim}14Kg_f/cm^2$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.677-680
• /
• 2008

The surface of particles was energetically modified by inter-grinding OPC and BFS in vibration mill for improvement of the early strength and low-heat evolution of concretes. BFS was pre-grinding in ball-mill to 2535(BS2) and 3245 $cm^2/g$(BS3), in blaine surface area. The inter-grinding time in vibration mill was changed from 10 minutes to 30 minutes. And Mixing ration of BFS to OPC was changed in 60, 70, 80%. After inter-grinding, the change of specific surface area, particle size distribution, hydration heat of cement and compressive strength of mortar were measured. As the result of comparison test with LHC, it was found that the mixture and inter-grinding time satisfying the value of over 100% of compressive strength for 7 days and under 170J/g of heat of hydration for 72 hours. and it was confirmed that the possibility of low heat slag cement utilizing blast furnace slag(BS2, BS3) with the low fineness in high volumes.

• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.311-316
• /
• 2010

This study aimed to prepare antimony-doped tin oxide (ATO) dispersion with high stability. The methods to achieve this goal were sought by investigating the changes of ATO particle size, size distribution, dispersion property as wet ball milling treatment time increased. And the changes of wet ball milled ATO dispersion property were also investigated, as pH increased. The changes of ATO particle size and size distribution, according to wet ball milling treatment time were evaluated with laser diffraction particle size analyzer and scanning electron microscope (SEM). The changes of ATO dispersion property, as wet ball milling treatment time and pH increased, were evaluated with zeta potential analysis and Turbiscan. By 60 min wet ball milling treatment time, ATO particle size decreased and size distribution became narrower, as the treatment time increased. After 60 min milling, the ATO particle size decreased to less than 30% of the initial size and the size distribution was narrowed to $0.1{\sim}5{\mu}m$ from $1{\sim}35{\mu}m$. However, more than 60 min milling, ATO particles aggregated and the particle size increased. ATO dispersion stability also increased as the treatment time and pH increased because the reduced particle size increased particle surface energy and repulsion between particles and the increased pH enhanced particle surface ionization. Hence, after proper length of wet ball milling treatment, highly stable ATO dispersion can be prepared, as increasing pH of the dispersion.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.352-355
• /
• 2003

비자성이며 비전도성의 물리적 성질을 갖는 자연산 퀄쯔(quartz)와 용암석 스코리아를 대상으로 마그네타이징 처리를 하여 분석하였다. 마그네타이징 처리를 위하여 강력한 기계화학적 분쇄 반응을 시켰으며, 분쇄 반응시 알코올계의 솔벤트를 반응 용매로 사용하였다. 퀄쯔와 스코리아의 마그네타이징 처리에서 비교적 비중이 큰 퀄쯔의 경우와 비중이 작은 스코리아의 경우에도 분쇄된 분말이 물에 뜨는 것을 확인할 수 있으며, 친유성으로 기름에 대한 흡착 성질이 우수함을 확인하였다. 자연산 퀄쯔와 함께 스코리아를 바탕물질로 하여 기계-화학적 반응 기술로 고 분산성 흡착반응에 의한 고분자 물잘 생성을 유도하여 나노복합체를 제조하였다. 반응의 처리조건과 적용과정에 따라서 기계-화학적 반응을 통하여 얻어진 물질은 자기적 성질과 유전체 및 전기적 성질을 동시에 나타낸다. 부착성 융합 복합물질의 특징을 고려하여 시그니토마그네틱스(Segneto-magnetics)로 분류되는 합성분말은 특히 유류성분에 대하여 높은 흡착성을 가지며, 강한 자기적 성질을 띄는 10-50 nm 두께의 하나 또는 그 이상의 이질적 융합 화합물 층이 석영이나 수정체의 표면에 합성되어 특유의 자기, 전기적 성질을 나타낸다.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.781-785
• /
• 1998

Material and electrochemical characteristics of petroleum coke of the nongraphitic carbon prepated with attrition milling for 6~48 hours and heat-treatment at $700^{\circ}C$ for 1 hour was investigated. The milling condition affects the particle size distribution, BET specific surface area and interlayer distance of petroleum cokes. Carbon electrode with petroleum cokes prepared at the milling time of 12~24 hours and having average particle size of $6{\sim}8{\mu}m$ showed best electrochemical characteristics form the investigation of cyclic voltammogram and charge-discharge characteristics.