• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.239-247
• /
• 2009

Pipe installation following excavation of pavement and underlying-soils induces settlements, cracks and bad roughness near utility cut. This study is to use PMT and LDWT in order to evaluate stiffness and/or degree of compaction of sublayers and backfill in utility cut section because no specially designed efforts for evaluating stiffness condition of the substructures below new pavement after pipe installation are offered at this time. From test results of PMT, comparable stiffness and/or degree of compaction in recompaction process is not obtained comparing to that of the existing sublayers before excavation. Thickness of the new surface layer after pipe installation must be designed thicker than that of the existing surface layer. It is verified that LDWT comparing to PMT is effective only to get stiffness and/or degree of compaction within limited depth from surface of materials, but it is not useful to evaluate stiffness of substructures in full depth in case of utility cut.

• Geotechnical Engineering
• /
• v.11 no.4
• /
• pp.63-74
• /
• 1995

Much of Taegu and Kyungpook areas are composed of sedimentary rocks. This paper is concerned with the engineering characteristi os of weathered shale soils and mudstone soils. In this study, the engineering characteristics of weathered shale soils and mudstone soils are investigated by performing tests such as compaction, gradation, CBR permeability and crushability according to compaction energy and water content. The experiments were carried out to obtain the relationships of the ratio of surface area(Sw'/Sw) and the indez of crushing(IC) The results are found as follows : (1) Weathered shale soils are larger than weathered mudstone soils in maximun dry den sixty, but weathered shale soils are smaller than weathered mudstone soils in OMC. (2) Minimum permeability is found in OMC's 1~2% wet side, and the more compaction energy is high, the more the change's range of permeability becomes narrow. (3) There is linear correlation between the ratio of surface area and the indez of crushing. IC : 14.286sw'/Sw -8.429(r=0.9937) (4) Soaked CBR value becomes maximum in OMC's dry side, and it decreases as the water content increases. Whereas the more compaction energy is high the more unsoaked and soaked CBR values are high in OMC's dry side, unsoaked and soaked CBR values are opposed to that in OMC's wet side.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.1
• /
• pp.225-228
• /
• 2004

Optimization of fluidized bed granulating conditions for yield, bulk density, and tapped density of powdered milk was determined using response surface methodology. Yield of powdered milk was greatly affected by feeding rate of water, and bulk density and tapped density could be reduced by decreasing of atomization pressure. The optimum conditions for fluidized bed granulating of powdered milk were predicted with 6$0^{\circ}C$ of inlet air temperature, 16 mL/min of feeding rate, and 2.1 bar of atomization pressure. Also 94% of yield 0.350 g/㎤ of bulk density, and 0.446 g/㎤ of tapped density of powdered milk could be obtained by the optimum granulating conditions.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.25-26
• /
• 2023

Free-form buildings serve as landmarks, and interest and demand are increasing. However, in the case of free-form concrete members, different curved surfaces are required depending on the location where they are used, and the formwork is custom-made and used. Concrete is poured into the manufactured formwork to produce FCP (Free-form Concrete Panel). However, since it is an atypical building that requires precise curvature, compaction cannot be performed after concrete is poured. This leads to the occurrence of bughole, which reduce the strength and aesthetics of concrete. Therefore, in this study, we intend to conduct basic experiments to develop a magnetic compaction device that can be used for FCP. As a result of the experiment, it was confirmed that the bug hole was improved when the magnetic compaction device was applied, and there was no significant difference in compressive strength and flexural strength. This technology can be used in the field of Free-form concrete where it is difficult to perform compaction work, and it is expected to be used as a basic research related to technology for new automatic compaction.

• Geotechnical Engineering
• /
• v.12 no.2
• /
• pp.107-114
• /
• 1996

A series of shear tests is performed to measure friction coefficients of the interface between different reinforcements and weathered granite soils. The reinforcements tested are smooth steel strip, Paraweb(friction tie) and geotextile with rough surface, while the weathered granite soils are composed of different, grain size distribution. Soils are compacted with the energy of 95% modified AASHTO and fully saturated before testing to simulate the worst site condition. Because of characteristics of the direct shear apparatus, shear strength is obtained in terms of drained condition. Test results show that the more fines the soils contain, the larger ratio of friction coefficient ($\mu=\frac{tan{\delta}}{tan{\Psi}}$) is obtained. Also the ratios are much higher for the Friction tie and the geotextile compared to the smooth steel strip. Those suggest that even weathered granite soils with 36% fines are possible to use as backfill of reinforced earth structures for the two reinforcements when a drainage system is provided.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.3
• /
• pp.283-293
• /
• 2015

In order to evaluate corrosion resistance of steel fiber-reinforced concrete, accelerated chloride migration and surface resistivity tests were conducted. In addition air content of fresh concrete, compressive strength and water absorption were measured for investigating fundamental characteristics of concrete. Two different water-cement ratios(0.44, 0.5) and three steel fiber contents(0.25%, 0.5%, 1%) were considered as variables. Note that all specimens cast with same compaction work. As a results, corrosion resistance decreased as steel fiber contents increased regardless of water-cement ratio when the concrete was compacted with same amount of work done. However, for concrete with same steel fiber content, the lower water-cement ratio showed the better corrosion resistance. It is found that enhancement of fluidity and enough compaction should be done for corrosion resistance of SFRC.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1997.05a
• /
• pp.61-64
• /
• 1997

본 연구는 매립 작업중인 준호기성매립지에서 유출가스를 측정하여, 다음과 같은 결론을 얻었다. (1) CH$_4$가스는 대부분 입형가스포집관에서 유출되며, $CO_2$가스는 총유출량의 약 50% 정도가 입형가스포집관을 통하여 유출된다. (2) 매립지 표면에서는 CH$_4$가스 보다 $CO_2$가스가 많이 유출된다. (3) 법면 복토층은 면적비율이 작으나 가스 발생량이 많으며, 특히 $CO_2$가스의 발생율이 높다. (4) 쓰레기층 표면에서의 CH$_4$가스 발생량은 미소이므로 무시하여도 된다. (5) 쓰레기층 노출, 복토층 다짐정도등에 따라 발생량의 변화를 보인다. (6) 매립부에서 새로 반입된 쓰레기층에서 $CO_2$가스 유출량이 많다. (7) 가스포집관과 복도 표면을 포함한 가스 유출량은 CH$_4$가스 유출이 많으나, 전체로는 $CO_2$가스 유출량이 많다.

• Journal of the Korean Society for Railway
• /
• v.18 no.1
• /
• pp.53-62
• /
• 2015

LWDT was developed for use as an alternative technique to measure the stiffness of trackbed soils. In this study, numerical and theoretical analyses of LWDT's acting mechanism were performed. The effectiveness of the adapted elastic formula used for calculation of the dynamic modulus, Evd, was investigated theoretically and also numerically by running ABAQUS analysis. The minimum thickness of the upper layer is proposed based on the analysis. Correction factors for the formula of elastic modulus are also proposed in this study. In the future, following field test results and laboratory mechanical tests such as the resonant column test, a guideline for the use of LWDT as a standard test protocol in track construction sites, as a measuring tool for the degree of compaction and/or stiffness and dynamic modulus, will be proposed based on this analysis.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.1
• /
• pp.49-55
• /
• 2009

In this study, reduction methods of surface air void were examined for high performance concrete having high viscosity. The effects of assumed influencing factors such as form types, form-coating materials, tamping equipments and methods were examined based on the tests on mock-up specimens made of high performance concrete. The test results can be summarized as follows: As for form types, the most favorable results were obtained when coated plywood form was used with panel-shape tamping equipments at the contact region with concrete, the second and the third being the water/air-permeable sheets and steel with coated plywood, respectively. As for tamping equipments, a vibrator with 6.5cm diameter was most effective. Finally, the shorter the tamping intervals, the better the reduction effect of surface air void. As a conclusion, an improved method was proposed to reduce surface air void and it was verified with the test result that only four air voids as large as $5{\sim}10mm$ are found in the are of $1m^2$.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1509-1521
• /
• 2013

Social demand for the stability of structures lead to the development of the technology to accomplish it. The non-destructive seismic technique, which is able to assess structural integrity of infrastructures, belongs to this category. Seismic technique is focused on the measurement of seismic velocity propagating through the material, and has to utilize sensors coupled to material surface, which does not allow the testing to be performed on the fly. In this paper, a general vocal microphone, which works as a non-contact sensor, was adopted to facilitate seismic testing with mobility and efficiency improved. The target of using microphones was oriented toward quality assessment of compacted subgrade, stiffness evaluation and health monitoring of concrete structures. Experimental parametric study and field applications were performed to investigate reliability and efficiency of microphones. Finally, the optimal test configuration of microphones was suggested for resonance tests and surface-wave tests.