• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.121-134
• /
• 1999

In this paper, a ship calculation program is developed, which prof[nuts hydrostatics and volume calculation intact and damage stability and hull variation. Hull form and compartment geometry are expressed with NURBS curve wire-frame model. Hydrostatics and volume calculation are performed directly with the intersection method between section geometry and 3D planar surface. Equilibrium ship position is calculated with hydrostatic equilibrium equation which is linearized by 1st order Taylor series expansion sequentially. The developed program shows more accurate results and easy uses than the latter.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.4
• /
• pp.387-394
• /
• 2000

The nonlinear modal interaction of an autoparametric system under a broadband random excitation is investigated. The specific system examined is an autoparametric vibration absorber with internal resonance, which is typical of many common structural configurations. By means of Gaussian closure scheme the dynamic moment equations explaining the random responses of the system are reduced to a system of autonomous ordinary differential equations of the first and second moments. In view of equilibrium solutions of this system and their stability we examine the system responses. We could not find the destabilizing effect of damping, which was reported in References (18) and (20). The saturation phenomenon, which is well known in deterministic nonlinear system, did not take place lot this system subject to broadband random excitation.

• Fire Science and Engineering
• /
• v.23 no.5
• /
• pp.17-23
• /
• 2009

Moisture evaporates, when concrete is exposed to fire, not only at concrete surface but also at inside the concrete to adjust the equilibrium and transfer properties of moisture. The equilibrium properties of moisture are described by means of water vapor sorption isotherms, which illustrate the hysteretical behavior of materials. In this paper, the prediction method of the moisture distribution inside the concrete members at fire is presented. Finite element method is employed to facilitate the moisture diffusion analysis for any position of member. And the moisture diffusivity model of high strength concrete by high temperature is proposed. To demonstrate the validity of this numerical procedure, the prediction by the proposed algorithm is compared with the test result of other researcher. The proposed algorithm shows a good agreement with the experimental results including the vaporization effect inside the concrete.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.62-62
• /
• 2016

대하천에서의 하도정비 및 보 신설 후 다양한 하천환경변화가 예상됨에 따라 각종 변화에 의해 발생할 수 있는 현상들을 예측하고 환경변화에 의한 재난을 예방하기 위한 대책수립이 절실히 요구되고 있는 실정이다. 하천에서의 하상변동은 경우에 따라 홍수위 상승, 저수 기능 감퇴, 용수와 취수 방해, 유사에 의한 오염원 확산 등의 문제를 발생시킬 수 있다. 기후변화에 따른 강우패턴의 변화로 하천 내 수리적 요소가 변화되고 그로인해 발생하는 하상 변동의 예측이 필요하다. 만일 유역의 특성이 유지된다면 하천의 동적평형상태인 정비 이전의 하천으로 돌아가려고 할 것이다. 하천이 준설로 넓어지고 깊어진 상태로 이전의 동적인 평형상태로 돌아가려고 하도가 좁아지고 얕아질 것이다. 그러나 기후변화로 인해 유역에서의 유량 및 유사량이 달라질 것으로 예상된다. 하지만 하상변동모델과 기후변화를 연계하여 하도의 변화를 비교 분석한 연구는 매우 드물다. 본 연구에서는 기후변화에 의한 유량의 변화에 따른 시나리오를 구성하고 장기간, 장구간에 걸친 하상변동 양상을 예측하였다. 준2차원 수치모형인 GSTARS를 이용하여 낙동강 상류에서 상주보 구간 사이의 기후변화 영향을 분석하고자 장기 기후시나리오를 구성하고 유사량 공식과 수류 튜브 개수에 따른 각각의 시나리오별 하상변동 양상을 예측하고 최심하상고, 횡방향에 따른 모의결과를 분석하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.476-476
• /
• 2023

해저면에 놓인 물체는 주변의 국소 흐름 변화에 의해 해저면 전단응력이 국부적으로 변화하는 과정에서 침식과 퇴적이 발생하게 되면서 해저면 지형의 변화에 의해 움직임이 발생한다. 이때 물체의 크기, 무게, 밀도와 형상에 따라 구름, 미끄러짐, 액상화 현상 또한 동반 될 수 있다. 본 연구에서는 해저면에 놓인 물체의 시간변화에 따른 매몰심 변화를 예측하고자 하였다. 물체는 원형 단면의 실린더 형태로 고려했다. 시간변화에 따른 매몰심 변화를 평형 매몰심으로의 접근속도에 관련된 인수와 매몰심 변화량으로 기본방적식을 구성하였고, 이를 유한 차분식으로 수립하였다. 최종 평형 매몰심 계산은 Friedrichs et al.(2016)의 경험식을 사용하였다. 앞선 연구에서 김효섭 등(2016)은 시간에 따른 세굴심 변화 모델 STEP-K를 제시한 바 있다. 시간변화에 따른 연직방향 실린더 주변에서의 국소세굴심을 예측하는 기법으로, 해저면에 놓인 수평방향 물체 주변의 매몰심 발달을 예측하기 위해 매몰 발생에 대한 시간의 척도를 새롭게 제안하였다. STEP-K에서 사용했던 KC수를 대신해 흐름-단주기 파랑 공조시의 해저면의 전단응력을 대표할 수 있는 대표전단응력을 사용할 수 있게 하였다. 보정계수를 통해 현장 또는 실험실 단위의 자료가 가용한 경우 식을 보정할 수 있다. 제안한 매몰심 예측기법은 Elmore et al.(2007)의 매몰실험 관측자료를 활용하여 보정하였다. 결과적으로 보정자료에 대한 시간에 따른 매몰심의 변화양상을 잘 재현하였으며, 향후 우리나라 해양환경 자료를 활용한 보정을 통해 적용성을 높일 수 있을 것으로 기대된다.

• Resources Recycling
• /
• v.30 no.1
• /
• pp.14-25
• /
• 2021

As a demand of high-end steel raises, the importance of secondary refinement process also increases. However, the content of each component in molten steel, slag and inclusions change with the time, meaning the secondary refinement process is not an equilibrium state. Furthermore, many reactions occur between molten steel, slag, inclusion, refractory and alloying element during secondary refinement process. In order to consider the above complex reactions with non-equilibrium state, a few researchers developed kinetic models in secondary refinement process based on the experimental numerical equations. It is important to analyze and review to the previously reported models to develop a precise model. Therefore, in present study, the complex reaction models based on kinetic in secondary refinement process were analyzed, reviewed, and introduced. Moreover, the single reaction models also introduced which would be applied to the complex reaction models.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.632-637
• /
• 2010

Liquid-liquid equilibrium data for the quaternary system water +tetrahydrofuran + butyl acetate + isoamyl alcohol mixture were measured at 298.15 K and atmospheric pressure. Binodal curves, tie-lines, distribution, and selectivity for the quaternary system have been determined in order to investigate the effect of using binary solvents, butyl acetate and isoamyl alcohol, on extracting tetrahydrofuran from aqueous solution. In addition, these experimental tie-line data were also compared with the values predicted by the UNIFAC model. For the quaternary system, an average root-mean-square deviation for the system in 75/25, 50/50, and 25/75 mass ratios as mixed solvents are(3.35, 5.21 and 5.65) %, respectively.

• Journal of the Korean Chemical Society
• /
• v.56 no.6
• /
• pp.692-699
• /
• 2012

The aim of the present study is to explore the possibility of utilizing loess and fly ash as well as activated carbon for the adsorptive removal of PCBs in transformer oil. Here, we investigated the effect of various factors such as temperature (5, 25, 55), contact time (30 min-3 day) and adsorbent does (1, 2.5, 5, 10 g) in detail. It was found that PCBs adsorption rate from transformer oil by activated carbon is more favored than loess at the equilibrium time of 60 minutes. The equilibrium data for both activated carbon and loess is fitted well to the Freundlich isotherm model. The rate constant and activation energy of PCBs adsorption in transformer oil on each adsorbent was analyzed by fitting a kinetic model at 5, 25 and $55^{\circ}C$. From the thermodynamic parameters, the PCBs adsorption process for transformer oil/activated carbon and loess system is spontaneous and endothermic in nature.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.4
• /
• pp.1-10
• /
• 1983

The deformation and crack width of concrete walls of slabs, plates, panels and shells reinforced by a regular rectangular net of reinforcing bars and subjected to in-plane (membrane) internal forces is analyzed on the basis of a realistic model which takes into account the frictional-dilatant behavior of rough interlocked cracks, the effect of tension stiffening, and the dowel action of bars at crack crossings. Extensive numerical computer studies are carried out, and the reinforcement designs obtained from equilibrium conditions alone on the basis of either the classical frictionless approach or the recent frictional approach are compared in terms of the resulting crack widths. It is found that the use of frictional equilibrium design based on a low friction coefficient leads to a much smaller crack width than the classical frictionless design. The influences of bar diameter and crack spacing on the crack width are also studied. The model allows more realistic deformation analysis of reinforced concrete structures.

• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.166-172
• /
• 1999

Fixed-bed adsorption of metal ions on chitosan bead was studied to remove heavy metal ions in waste water. Chitin was extracted from carb shell and chitosan was prepared by deacetylation of the chitin. The chitosan in bead was used as an adsorbent for heavy metal ions. Freundlich and Langmuir isotherm was determined from the experimental results of equilibrium adsorption for individual metal ion ($Cu^{2+}$, $Co^{2+}$, $Ni^{2+}$) on chitosan bead. Adsorption strength of metal ions decreased in the order of $Cu^{2+}$>$Co^{2+}$>$Ni^{2+}$ ion. Breakthrough curves of single and multicomponent adsorption for metal ions were obtained from the experimental results of fixed-bed adsorption. The breakthrough curves were analyzed by simulation with fixed-bed adsorption equation based on LDFA (linear driving force approximation) adopted LAS (ideal adsorbed solution) theory which can predict multi-component adsorption isotherm from individual adsorption isotherm. The behavior of fixed bed adsorption for single and multi-component system could be nicely simulated by the equation.