• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.3
• /
• pp.220-226
• /
• 2011

This paper presents the novel work for source localization of serial multiple impacts in a plate sructure. It is difficult to identify the source of serial multiple impacts with the current source localization techenology(SLT) because of the overlapping of dispersive wave induced by multiple impacts and the reflaction from the edge of the plate. In this paper, the new method is suggested for source localization. The method is developed based on the SLT with pre-signal processing such as some limitation for the selection of three sensors, the frequency range for TFA and impact time interval. Results from numerical simulation and experiment in isotropic plate structure are presented, which show the capability of the proposed method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.752-755
• /
• 2001

In order to investigate the vibration characteristics of fluid-structure interaction problem, we modeled two rectangular identical plates coupled with bounded fluid. The fixed boundary condition along the plate edges and an ideal fluid are assumed. MSC/NASTRAN was used to perform finite element analysis and analytic solutions were compared with experimental solutions to verify finite element model. As a result, comparison of FEM and experiment show good agreement, and the transverse vibration modes, in-phase and out of-phase, were observed alternately in the fluid-coupled system. The effect of distance between two rectangular plates on the fluid-coupled natural frequency is investigated.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.740-745
• /
• 2003

The so-called boundary node method (or NDIF method) that was developed by the authors has been extended for free vibration analysis of arbitrarily shaped plates with free edges. Since the proposed method is based on the collocation method, no integration procedure is needed on boundary edges of the plates and only a small amount of numerical calculation is required. A special coordinate transformation has been devised to consider the complicated free boundary conditions at boundary nodes. By the use of the special coordinate transformation, the radius of curvature involved in the free boundary conditions can be successfully dealt with. Finally, verification examples show that natural frequencies obtained by the present method agree well with those given by exact method and other analytical methods.

• Journal of KSNVE
• /
• v.6 no.6
• /
• pp.781-790
• /
• 1996

The goal of current research is to suppress the acoustic noise radiated from vibration of composite plate structure. The induced noise can be reduced through the control of the corresponding structural vibration modes by using the piezoelectric materials as actuator. The acoustic fields are to be analyzed through the boundary element method (BEM) based on the Rayleigh intergral equation and structural system through the finite element method (FEM). The suppression of rediated sound is studied by adaping the piezoelectric material as the distributed actuator. Numerical results are presented on the sound radiation from composite plate of arbitrary boundary conditions, the noise reduction adapting the piezoelectric materials as distributed actuator. The results show the effectiveness and possibility of piezoelectric actuator in the control of sound radiation from composite structure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11b
• /
• pp.170-173
• /
• 2005

The objective of this paper is to perform measurements of power transmission and reflection coefficients in a coupled plate. The coupled plate has been divided into 2 subsystems. The out-of-plane vibration has been only considered with assumption of relatively small in-plane vibration. The coupling loss factors have been measured with consideration of the power balance condition. The power transmission and reflection coefficients has been estimated from the measured values of the coupling loss factors. The measured power transmission and reflection coefficients have been compared with the corresponding theoretical coefficients in a semi-infinite coupled plate.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.383-388
• /
• 2008

A modeling method for the impact analysis of plate structures employing Hertzian contact theory is presented in this paper. Since local deformation as well as bending deflection of the plate occurs due to the collision, it has to be considered for the impact analysis. When the coefficient of restitution is employed for the impact analysis, the local deformation is not considered. For more accurate and reliable impact analysis, however, the local deformation should be considered. The effects of the location of collision and the collision mass on the impact duration time and the contact force magnitude are investigated through numerical studies employing Hertzian contact theory.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.9
• /
• pp.876-883
• /
• 2009

The radiation of sound from a rectangular plate with a guided edge condition is investigated. By taking this particular boundary condition into account, simple analytical forms of the average radiation efficiency and radiation power based on the modal approach can be found, where the cross-modal terms can average out for all possible point excitation locations. Design variables of the plate such as thickness, aspect ratio, and damping that are closely related to the sound radiation are mainly discussed. The radiation power of the guided plate is found to be governed by the piston mode as well as the critical frequency. While both the radiation efficiency and the radiation power seem to be influenced by thickness and a large aspect ratio, damping loss factor seems less important to the radiation power. It is also shown that no clear corner and edge mode regions may be found for the guided case, unlike the pinned.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.4
• /
• pp.374-383
• /
• 2011

A numerical model based on a mode method coupling beams and a rectangular plate is proposed to estimate radiation characteristics of an edge-clamped rectangular plate. The radiation efficiency and radiation power in the audio frequency range including the critical frequency can be predicted. The proposed model is rather simple and straightforward and gives reliable results comparing to the previous studies. The estimated radiation characteristics are compared to those of the pinned condition plates and also to those based on the formulae proposed by Maidanik. The radiation efficiency of the clamped plate seems a little higher than that of the pinned plate in the frequency range of corner and edge modes. It is explicitly shown that the power as well as efficiency at high frequencies is not influenced by these edge boundary conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.6 s.237
• /
• pp.889-894
• /
• 2005

A modeling method for the modal analysis of cantilever plates undergoing in-plane translational acceleration is presented in this paper. Cartesian deformation variables are employed to derive the equations of motion and the resulting equations are transformed into dimensionless forms. To obtain the modal equation from the equations of motion, the in-plane equilibrium strain measures are substituted into the strain energy expression based on Von Karman strain measures. The effects of two dimensionless parameters (related to acceleration and aspect ratio) on the modal characteristics of accelerated plates are investigated through numerical studies.

• Journal of Power System Engineering
• /
• v.9 no.1
• /
• pp.42-49
• /
• 2005

The vibration analysis of a rectangular plate with stiffeners is formulated by using the transfer stiffness coefficient method (TSCM). This method is based on the concept of the successive transmission of stiffness coefficients which are defined as the relationship between the force vector and the displacement vector at an arbitrary nodal line. In order to confirm the validity of the present method, bending vibration analysis for a rectangular plate with stiffener is carried out on a personal computer by using the present method and the finite element method (FEM). Through comparing computational results of the TSCM and the FEM, the effectivness of the TSCM from the viewpoint of computational cost, that is, computational time and storage is demonstrated.