• Geotechnical Engineering
• /
• v.10 no.2
• /
• pp.41-56
• /
• 1994

Under the groundwater level, the tunnel face is affected by the seepage force and the groundwater flow may cause a trouble to the tunnel support systems. The appropriate methods of analysis and design in the tunnel face and the lining, considering groundwater flow according to tunnel drainage condition are presented in this thesis. First, the effect of seepage on the stability of tunnel face was studied. Seepage force was estimated by the 3-D finite element analysis and the stability of tunnel face was checked by analytical method. Furthermore, using the finite difference method the stress and displacement on the face were computed for either case, where the seepage force is or is not considered, and the effect of seepage on the tunnel face stability was evaluated. Second, the effect of seepage force on the tunnel lining when construction is finished and steady state seepage flow occurs was studied and a design methodology considering seepage effect was made. Consequently, in case where the groundwater level remains almost unchanged and the steady state groundwater flow occurs, the proper countermeasures for face staility are required according to the condition of groundwater flow. Moreover, the tunnel lining should be designed and constructed considering the seepage force occuring by the groundwater flow toward the tunnel linings.

• Geotechnical Engineering
• /
• v.13 no.4
• /
• pp.37-54
• /
• 1997

This paper is to investigate the bearing capacity and the failure mechanism of slope subjected to strip surcharges adjassent to embankment slope of sandy soil. Parametric model tests under plain strain condition were performed by changing width of footing, relative density of slope materials, and position of footing from the crest of slopes. For model tests, Jumunjin standard sand was used as the slope material and its relative density was 45% and 70%, respectively. The angle of slope was formed with 1 : 1.5 and 1 2. Rigid model footings, made of aluminuu were used with their widths of 4, 7, 10 and 12cm. For the position of model footing, position ratios, distance of model footing from the crest of slope divided by footing width, were 0, 0.5, 1, 2, 3, 4, 5. Failure mechanism was observed by using ink colored sands and markers inserted in model slopes. Ultimate bearing capacity obtained from tests was analyzed and compared with limit equilibrium method, limit analysis method and empirical equation. Characteristics of load-settlement curves and failure mechanism were also analyzed and compared with the existing theories. Thus, their effects on ultimate bearing capacity of model footing adjacent to slope were assessed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.12B
• /
• pp.1450-1458
• /
• 2011

The HPcN (Hybrid & high Performance Convergence Network) in research networks means environment which can provide both computing resource such as supercomputer, cluster and network resource to application researchers in the field of medical, bio, aerospace and e-science. The most representative research network in Korea, KREONET has been developing following technologies through the HERO (Hybrid Networking project for research oriented infrastructure) from 200S. First, we have constructed and deployed a control plane technology which can provide a connection oriented network dynamically. Second, the integrated resource management system technology has been developing for reservation and allocation of both computing and network resources, whenever users want to utilize them. In this paper, a testbed network is presented, which is possible to reserve and allocate network resource using the integrated resource management system. We reserve network resource through GNSI (Grid Network Service Interface) messages between GRS (Global Resource Scheduler) and NRM (Network Resource Manager) and allocate network resource through GUNI (Grid User Network Interface) messages between the NRM (network resource manager) and routers, based on reservation information provided from a user on the web portal. It is confirmed that GUNI interface messages are delivered from the NRM to each router at the starting of reservation time and traffic is transmitted through LSP allocated by the NRM.

• Cartoon and Animation Studies
• /
• s.46
• /
• pp.207-231
• /
• 2017

Printmaking is a field of fine arts and is placed on a vague boundary that is perceived as a commercial product with a popular character due to the speciality of editions. Advances of modern science and technology has developed a new technique of printmaking, and the fusion of printmaking and computer has shown the possibility of reproduction art. Reproduction printmaking has been heavily influenced by photography and extended areas, and the various forms of printing have brought about many changes and attempts by stimulating the possibilities of indirect art at various angles. As the history of printmaking and technology closely relate, the development of computer makes widespread expansion of plural artistry, technological and artistic change. A new conceptual shape can be created on the copied image simply by placing the material of the print on the smoothly flat surface expressed in digital form. The process and the result of such work show the area of unique work which is different from the value of the $\grave{a}$ la carte art or the characteristics of the material given by the print. The deprecated perception of reproducibility evaluated the value of the work in a direct sense of printmaking. It is undeniable that it is devalued by a bundle of works regardless of the value of each edition. However, the physical properties of the prints on the paper are brought up with hand drawings drawn on the canvas by hand. And it becomes an opportunity to show new aspect and change through the process of combining digital print information on paper. The diversity of media is sometimes a controversy of identity between art and technology. In the future, it should be discussed how the limit of the media which can be enjoyed in the field of art can be set as a standard.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.3
• /
• pp.377-387
• /
• 1997

Primary fluorescence characteristics of ten standard solutions of organophosphates, sea water, and water from agricultural land were investigated by fluorescence contour. All the standard solutions of organophosphates has shown characteristics countours. Their emission maxima were shown between 296 nm and 437 nm. According to their numbers of emission maxima on the fluorescence contours, the organophosphates can be categorized in two different groups. Ateric and Diazinon are the first group with two emission maxima. DDVP with other seven standard organophosphates belong to the second group. The second group has two subgroups. One is characterized by the similar emission and excitation maxima, which are 310 nm and 280 nm, respectively. Those are DDVP, Hinosan, Kitazin, Locsion, Meta. The other sub-group shows quite different emission and excitation maxima from the first sub-group. They are Monopho, Thaconyl and Gropho and their emisson maxima were in far longer (437 nm) or shorter wavelength (296 nm). From agricutural samples, one of the investigated organophosphates was detetected by its characteristic retention time $(t_r=12min)$. HPIC-fluorescence data gave an additional parameter for differentiation between two organophosphates which has similar excitation and emission maxima.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.1
• /
• pp.39-45
• /
• 2005

As a basic research for the development of a non-invasive blood glucose sensor using millimeter waves, we have presented a method for measuring the dielectric properties of high loss dielectrics, based on the reflection method, and investigated the variation of the dielectric properties of glucose-water and glucose -0.9% NaCl solutions in the 10～90 GHz range. In the proposed method, a minimal reflection condition is formed by placing a specially-chosen low-loss plane-parallel plate in front of a high-loss medium under test at a given frequency range. Using the minimal power reflection coefficient and the corresponding frequency at this condition, tile dielectric properties of the medium can be determined. The measured results on pure water have shown the adequacy of the proposed method. The measured results on glucose-water and glucose -0.9% NaCl solutions in the 10～90 GHz range showed that the variations of the dielectric properties of glucose solutions according to the change of their glucose concentration were maximum in the 30～45 GHz range. From these facts we concluded that the variation of about 3 mole/L in the glucose solutions must be distinguished With the measurement accuracies of ±0.1 dB and ±0.01 GHz.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.1
• /
• pp.1-11
• /
• 2005

Several Solid Freeform Fabrication Systems(SFFS) are commercialized in a few companies for rapid prototyping. However, they have many technical problems including the limitation of applicable materials. A new method of agile prototyping is required for the recent manufacturing environments of multi-item and small quantity production. The objectives of this paper include the development of a novel method of SFFS, the CAFL/sup VM/(Computer Aided Fabrication of Lamination for Various Material), and the manufacture of the various material samples for the certification of the proposed system and the creation of new application areas. For these objectives, the technologies for a highly accurate robot path control, the optimization of support structure, CAD modeling, adaptive slicing was implemented. However, there is an important problem with the conventional 2D lamination method. That is the inaccuracy of 3D model surface, which is caused by the stair-type surface generated in virtue of vertical 2D cutting. In this paper, We design the new control algorithm that guarantees the constant speed, precise positioning and tangential cutting on the 5DOF SFFS. We develop the tangential cutting algorithm to be controlled with constant speed and successfully implemented in the 5DOF CAFL/sup VM/ system developed in this paper. Finally, this paper confirms its high-performance through the experimental results from the application into CAFL/sup VM/ system.

• Journal of the Korean Chemical Society
• /
• v.18 no.5
• /
• pp.329-340
• /
• 1974

Sulfadiazine, $C_{10}H_{10}N_4O_2S$, forms monoclinic crystals of space group $P21}c$ from a mixture of acetone and ethanol with $a=13.71{\pm}0.04,\;b=5.84{\pm}0.03,\;c=15.11{\pm}0.05{\AA},\;{\beta}=115.0{\pm}0.3^{\circ}$, and four molecules per cell. Three dimensional photographic data were collected with $CuK\alpha$ radiation. The structure was determined using Patterson and Fourier synthesis methods and refined by block diagonal least-squares methods with isotropic thermal parameter for all non-hydrogen atoms. The final R value was 0.15 for the 1517 observed independent reflections. The dihedral angle between the planes through the benzene ring and the pyrimidine ring is $76^{\circ}$. The conformational angle formed by the projection of the S-C(5) bond with that of N(1)-C(1) where the projection is taken along the S-N(1) bond is $77^{\circ}$. The imino nitrogen atom, N(1), and pyrimidine nitrogen atom, N(3), form intermolecular $N-H{\cdots}N$ hydrogen bond between the molecules related by center of symmetry. Amino nitrogen atom, N(4), forms two intermolecular $N-H{\cdots}O$ hydrogen bonds, with O(1) and O(2) atoms of different molecules separated by b. A two dimensional network of hydrogen bonds form infinite molecular sheets parallel to the (100) plane. Adjacent sheets are bound together by van der Waals forces.

• Journal of the Korean Chemical Society
• /
• v.40 no.3
• /
• pp.161-166
• /
• 1996

6-ethyl-5,6-dihydrouracil($C_6H_10N_2O_2$) is monoclinic, space group $$P2_{1}c}$$ with a=10.302(2), b=10.419(3), $c=7.095(1)\AA$, $\beta=106.6(0)$, Z=4, $V=729.7(3)\AA$^3$$, $D_c=1.29 g/cm^3,\;{\lambda}(MoK\alpha)=0.71073\AA$, $\mu=0.010cm^{-1}$, F(000)=304, and R=0.054 for 1070 unique observed reflection with F>4.0 $\sigma(F).$ The structure was solved by direct methods and refined by full-matrix least-squares refinement with the fixed C-H bond length at $0.96\AA.$ The hydrouracil molecule makes an envelope conformation with the ethyl substituent oriented to an axial position attainable to a varying degree of steric strain. There are two intermolecular hydrogen-bondings via N-H---O interactions, being nearly parallel to the 100 plane. The shortest distance between molecules is $3.187\AA$ of C(4) and O(8) (-x,-y, 1-z).

• Journal of the Korean earth science society
• /
• v.25 no.5
• /
• pp.348-363
• /
• 2004

The purpose of this study was to classify types of preconception about the motion of the moon held by middle school students and find out how the lesson applying cognitive conflict instructional model changes their conceptual view of the motion of the moon. A quantitative study was first conducted with 48 ninth graders and then followed by a qualitative study. In the qualitative study, male and female students were organized into groups of five and ten respectively. Students were instructed to observe the motion of the moon about for a month and at the same time were taught via the cognitive conflict instructional model for three class periods. Data were collected from interviews and a questionnaire evaluating the degree of concept development that each student showed. A majority of students were found to hold misconceptions formed from elementary school programs on the motion of the moon. Further, students showed lack of scientific ability to interpret the phenomena of the moon. This study showed that the cognitive conflict instructional model was effective for students to make progress regarding their conceptual views of the motion of the moon. However, it was observed that misconceptions by students may possibly occur when two dimensional figures or miniatures were used.