• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.581-589
• /
• 2020

In this paper, a solid capsule was prepared using a crystal growth type inorganic material capable of hydration reaction, the quality and mechanical healing properties of self-healing mortar with solid capsules were evaluated. Solid capsules were mixed 5% by mass of cement. Reloading test results of compressive load, it was found to improve about 20% on average for the natural healing effect of Plain, in the case of the elastic range, the healing rate was about 79% at the 7 days of healing age and 98% at the 28 days of healing age. Reload test results of flexural load, in the case of the elastic range, the healing rate was about 79% at the 7 days of healing age and 98% at the 28 days of healing age. Through these results, it is judged that the healing performance of solid capsules has also an effect on mechanical healing properties such as strength in addition to the durability properties obtained by the permeability test. Since the strength tends to decrease as the solid capsules are mixed, it is considered necessary to compensate.

• The Journal of Engineering Geology
• /
• v.27 no.1
• /
• pp.51-58
• /
• 2017

The purpose of this study was to quantitatively evaluate the state of rocks in load steps by using the low-frequency ultrasonic flaw detection method. The initial Vp-velocities measured with a CND tester were in the order of Z-axis < X-axis < Y-axis, with 1687.5 m/s along the X-axis, 1690.7 m/s along the Y-axis, 1548.3 m/s along the Z-axis, and an average of 1642.2 m/s. The overall average of the Q vlaues, measured with a Silver Schmidt hammer, was 62.6, which corresponds to a uniaxial compressive strength of ~105 MPa. The Vp-velocity, measured with a low-frequency ultrasonic flaw detector at load steps of 50%, 60%, 70%, and 80%, typically decreases in the order of X-axis < Y-axis < Z-axis with increasing load steps. This oder contrasts with that of the initial Vp-velocities. As the load step increases the factors that reduce the Vp-velocity in the X-axis direction are more influential than those in the Y-axis or Z-axis directions. This indicates that the initial state of rocks can vary and is dependent on the stress state.

• Resources Recycling
• /
• v.20 no.1
• /
• pp.37-45
• /
• 2011

This study was conducted to recycle flotation tailings as non-sintered construction materials considering the economic and eco-friendly treatments. The particle size distribution( median $220\;{\mu}m$) of flotation tailings from Soon-shin mine was confirmed to be larger than that(median $140\;{\mu}m$) of tailings from Sam-kwang mine. Thus we investigated the properties of non-sintered eco-brick producted with the tailings from Sam-kwang mine and non-sintered water permeable block producted with the tailings from Soon-shin mine. Compressive strength of non-sintered water permeable block which was made with less than 25 wt% of tailings from Soon-shin mine was met with products class(over 14.70 MPa) of water permeable concrete(EL 245) from KEITL. Meanwhile, the coefficient of its permeability wasn't met with the products class( over $1.0{\times}10^{-2}\;cm/sec$). The properties of non-sintered eco-brick with less than 40 wt% of tailings from Sam-kwang mine were satisfied with third class in sintered clay brick products standard(KS L 4201). The non-sintered eco-brick as a result of leaching test on heavy metals by KSLT was verified to be environmentally stabile.

• The Journal of Engineering Geology
• /
• v.33 no.4
• /
• pp.599-609
• /
• 2023

In the seismic retrofitting of harbor breakwaters in Korea, the recovery rate is often uncertain due to site conditions and site conditions, and problems continue to arise. Therefore, in this study, we analyzed the recovery rate and compressive strength of the improved material through drilling survey by grouting confirmation method after applying low-fluidity mortar injection method, and furthermore, we checked the elastic modulus by downhole test and tomography to confirm the reinforcement effect of soft ground after ground improvement. The experimental results showed that the average shear wave velocity of the ground increased from 229 m/s to 288 m/s in BH-1 and BH-3 boreholes to a depth of 28.0 m, and the average shear wave velocity of the ground to a depth of 30.0 m tended to increase from 224 m/s to 282 m/s in the downhole test. This is believed to be a result of the increased stiffness of the ground after reinforcement. The results of the tomographic survey showed that the Vs of the soft ground of the sample at Site 1 increased from 113 m/s to 214 m/s, and the Vs of the sample at Site 2 increased from 120 m/s to 224 m/s. This shows that the stiffness of the ground after seismic reinforcement is reinforced with hard soil, as the Vs value satisfies 180 m/s to 360 m/s in the classification of rock quality according to shear wave velocity.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.101-111
• /
• 2016

It is possible that aggregates add on to geopolymer based fly ash to mix mortar and concrete like cement. This is necessary to evaluate mineral composition, particle shape, surface, size distribution, density and absorption ratio for fine aggregates due to few detailed research to examine influence of fine aggregates properties on unhardened geopolymer concrete. In this research, used two different fine aggregates, Jumunjin sand(having quartz, mica, feldspar, pyroxene in mineral composition, more than 96% of total size between -0.60 and +0.30mm, angular shape and rough surface) and ISO sand(having almost all quartz in mineral composition, more than 51% size between -1.40 and +0.60mm, simultaneously varied size distribution, spherical shape and smooth surface). After an experimental result of the varied ratio of Si/Al=1.0-4.1 geopolymer paste, mix proportion respectively applied Si/Al=1.5 having the highest compressive strength to mortar and Si/Al=3.5 having the highest consistency to concrete. Geopolymer mortar by mixing with Jumunjin and ISO sand in varied range of 20-50wt.% showed flow size increase between 69.5 and 112.0mm, between 70.5 and 126.0mm respectively. Geopolymer concrete at an addition of 77wt.% of total aggregates ratio showed that average compressive strength was 32MPa and the consistency was favorable to molding. Since ISO sand observing varied size distribution, spherical shape, smooth surface, low absorption ratio resulted in advantageous properties on consistency of geopolymer, geopolymer concrete can be suitable for using the fine aggregates similar to ISO sand.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.11
• /
• pp.783-789
• /
• 2011

Recently, auto-thermal thermophilic aerobic digestion (ATAD) has a great attention for destruction of wasted sludge biomass in wastewater treatment plant. Reduction of sludge concentration has been successfully achieved with pilot scale ATAD and ceramic filtration process in field condition. However, high concentration of COD, total nitrogen (TN) and total phosphorus (TP) was observed in filtrate, which should be treated before recirculation of filtrate to biological wastewater treatment plant. This study was focused on removal of nitrogen and phosphorus contained in the filtrate of ATAD, using struvite crystallization method. The effect of operational and environmental parameters (such as, N, P and Mg ion concentration and molar ratio, pH, reaction time, agitation strength, seed dosage, and reaction temperature) on the treatment of TN and TP with struvite crystallization were evaluated. Magnesium (as $MgCl_26H_2O$) and phosphorus (as $K_2HPO_4$) ions were, if necessary, added to increase nitrogen removal efficiency by the crystal formation. Average concentration of $NH_4^+-N$ and $PO_4^{3-}-P$ of the filtrate were 1716.5 mg/L and 325.5 mg/L, respectively. Relationship between removal efficiencies of nitrogen and phosphorus and molar ratios of $Mg^{2+}$ and $PO_4^{3-}-P$ to $NH_4^+-N$ was examined. Crystal formation and nitrogen removal efficiencies were significantly increased as increasing molar ratios of magnesium and phosphorus to nitrogen. As molar ratio of $Mg^{2+}:PO_4^{3-}-P:NH_4^+-N$ were maintained to 2 : 1 : 1 and 2 : 2 : 1, removal efficiencies of nitrogen and phosphorus were 71.6% and 99.9%, and 93.8% and 98.6%, respectively. However, the effect of reaction time, mixing intensity, seed dose and temperature on the struvite crystallization reaction was not significant, comparing to those of molar ratios. Settled sludge volume after struvite crystallization was observed to be reduced with increase of seed dose and to be increased at high temperature.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.19 no.3
• /
• pp.125-131
• /
• 2013

In order to protect agricultural products against damage by physical load, various shock absorbing materials is used. As the demands of environment protection increase, the use of plastic materials have been restricted. On the other hand, Pulp mold products have some benefits - easy manufacturing, superior shock absorbing and eco-friendly. In order to develop pulp mold tray for melon packaging as shock absorbing packaging material, we investigated physical properties and vibration transmission characters of 180, 200 and 220 g pulp mold tray for melon. As the weight of pulp increased, compression strength and shock absorbing performance increased, while vibration transmissibility decreased. Especially in case of 180g pulp mold tray, it is not suitable for melon packaging because the transmitted vibration acceleration was higher than the forced vibration acceleration. And 200g pulp mold tray is suitable for melon packaging because the vibration transmissibility was lowest in three trays. And the vibration acceleration transmitted to the melon in edge of pulp mold tray was higher than to the melon in center of pulp mold tray. As the result of the simulated transportation test, the firmness of melon packaging using pulp mold tray was higher than that of conventional packaging. Therefore, these results suggest that pulp mold tray packaging could be suitable for melon packaging.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.65-65
• /
• 2017

밭작물 중 양파와 마늘은 높은 노동투하시간, 노임의 상승, 복잡한 수거 과정 등으로 최근 재배면적이 감소하는 추세이다. 밭농업 활성화 방안으로 생산비 절감과 작업 속도 향상을 위한 수확기계 개발 연구로 줄기절단기가 개발되었다. 이 연구는 줄기절단기 예취날의 설치각이 절단부하에 미치는 영향을 분립체 해석 기법으로 분석하고자 하였다. 실험에 사용한 시뮬레이션은 EDEM으로 인장탄성계수, 전단탄성 계수, 중첩길이, 입자 반경 및 질량, 상대속도를 이용하여 충돌시 힘을 해석하고 인장 및 전단강도, 한계, 결합 길이를 통해 입자간 결합을 설정할 수 있다. 시제품으로 설계된 줄기절단기의 치수를 활용하여 프로그램 상에서 줄기 절단 시뮬레이션을 진행하여 절단부하 결과를 얻도록 하였고 칼날 설치각을 30도, 45도, 60도로 변경하여 각각의 부하를 분석하여 경향성을 파악하고자 하였다. 실험에서 사용한 프로그램은 EDEM 2.7.1 Academic Research 버전이며 시뮬레이션을 진행한 PC의 사양은 Intel(R) $Core^{TM}$ i7-4790 CPU @ 3.60GHz, Memory 16.0GB이다. 줄기 절단 시뮬레이션에 적용시킨 줄기 모델은 마늘의 조건을 적용시켜 직경 1mm의 입자로 이루어진 지름 12mm, 높이 214mm의 원통형 모델이며 60.32N의 최대절단력을 가지고 있다. 줄기절단기는 2개의 회전날을 가지고 있으나 좌우대칭을 적용하여 절반에 대한 해석으로 하나의 회전날로 절단을 하도록 줄기 모델은 4조로 하여 3열을 140mm 간격으로 위치시켰다. 줄기절단기의 칼날은 반경 350mm로 회전하며 진행속도는 1.65m/s, 회전속도는 1680rpm으로 작업하도록 하였다. 시뮬레이션은 0.5초의 시간에 대해 해석하도록 하였으며 0.003초 간격으로 칼날에 가해지는 힘을 구하여 저장하도록 하였다. 시뮬레이션 해석시간은 약 116시간이었으며 설치각별 시간에 따른 칼날에 가해지는 압축력 값과 그래프를 얻을 수 있었다. 대부분의 시간에서 절단이 이루어지지 않으므로 0의 값을 나타내었으며 절단이 이루어지는 시점에 절단부하가 나타났다. 결과 해석을 위해 그래프의 피크 값들을 이용하였으며 그 중 상위 6개의 값으로 분석하였다. 30도, 45도, 60도의 설치각에 따른 절단부하의 평균 값은 각각 105.4N, 160.5N, 215.9N으로 나타났다. 설치각에 따른 절단부하의 경향성은 유의수준은 3.93%로 각각의 차이가 유의미하게 나타났으며 상관계수는 0.489로 증가하는 경향이 보였다. 그러나 $R^2$는 0.2394로 낮은 값을 보여 데이터 처리 방법의 개선과 적절한 회귀 모델의 적용이 필요하다. 향후 포장시험을 진행하고 복합적으로 분석하여 경향성을 자세히 분석하고자 한다.

• Restorative Dentistry and Endodontics
• /
• v.21 no.1
• /
• pp.107-120
• /
• 1996

복합레진은 조작이 용이하고 강도가 우수하며 중합시간이 짧고 법랑질과 상아질에 접착이 가능하며 연마성이 뛰어나고 자연스러운 색상을 나타내므로 심미적 수복에 가장 일반적으로 선택되는 재료의 하나이다. 대부분의 복합레진 kit에는 shade guide가 포함되어 있어 이를 기준으로 중합된 후의 복합레진 색조를 예상하여 선택하게 된다. 그러나 이러한 shade guide들은 대개 복합레진이 아닌 plastic으로 제조된 것으로 중합된 복합레진의 실제 색조와는 차이가 생기게 되며 결국 shade guide 자체의 문제점으로 인해 이상적인 색조선택이 어려워진다. 이에 본 연구에서는 국내에 시판되고 있는 5종의 복합레진 제품을 선정하여 분광 광도계를 이용해서 shade guide와 중합된 복합레진 사이의 색조차이를 측정, 비교 연구하였다. 직경 16mm. 두께 1.6mm의 plastic mold에 5종의 광중합형 복합레진(Z100, Prisma TPH, Tetric, Silux Plus, Herculite XR)을 충전하고 응축기에 넣어 압축한 후 제조사의 지시에 따라 광중합기로 중합시킨 후 mold에서 시편을 제거하여 보관했다가 젖은 sandpaper 상에서 순차적으로 연마하였다. shade guide는 step부분을 갈아내어 복합레진 시편과 동일한 두께로 만든후 연마하였다. 분광광도계에 shade guide를 넣고 CIE illuminant D65 하에서 spectral reflectance를 측정하고 해당 색조의 복합레진 시편도 통일한 방법으로 측정하고 $L^*$, $a^*$, $b^*$값과 ${\Delta}E^*$값을 얻은후 분석하여 다음과 같은 결과를 얻었다. 1. Z100의 D3, A3, B2 shade와 Prisma TPH의 B2 shade를 제외한 모든 시편에서 shade guide와 복합레진간에 육안으로 인지할 수 있는 색차(${\Delta}E^*$ > 1.0)가 관찰되었다. 2. 평균적으로 Z100이 가장 적은 색차를 나타내었고 Prisma TPH, Tetric, Silux Plus, Herculite XR 순으로 색차가 증가하였다. 3. Prisma TPH의 A2 shade. Tetric의 W shade. Silux Plus의 YB, U shade, Herculite XR의 L, LY shade는 ${\Delta}E^*$값이 3.3 이상으로 나타났다. 4. Z100, Prisma TPH, Tetric, Silux Plus에서는 복합레진보다 shade guide가 더 높은 $L^*$값을 보이는 경향이 나타났으며, Herculite XR에서만 복합레진이 더 높은 $L^*$값을 나타냈다. 5. 모든 시편에서 $b^*$ 값은 (+)로 관찰되었고, Z100, Prisma TPH, Tetric, Silux Plus의 shade guide는 복합레진에 비해 높은 $b^*$값을 보였다. 6. 모든 시편에서 $a^*$값은 (-)로 관찰되었고. Herculite XR 및 Silux Plus에서는 복합레진이 shade guide 에 비 해 낮은 $a^*$값을 나타냈다.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.9
• /
• pp.917-922
• /
• 2005

The wastewaters from textile and dyeing industries are difficult to treat due to its high pH, temperature, color intensity and non-biodegradable organic contents. This study investigated the removal of recalcitrant organics in a dyeing wastewater by using a packed bed reactor (PBR) that contained cell-immobilized pellets. The feed, obtained from an effluent of a biological treatment plant, had $SCOD_{Cr}$ of 330 mg/L and $SBOD_5$ of 20 mg/L on average. In immobilizing the cells to a Polyethylene Glycol(PEG) based medium, activated sludges from either a sewage treatment plant or an industrial wastewater treatment plant were used. When the empty bed contact time (EBCT) was above 8 hrs in the PBR, the $COD_{Cr}$ removal efficiency was over 50% and the $COD_{Mn}$ concentration was 72 mg/L or lower on average, which was substantially lower than the discharge standard of 90 mg/L. The results indicated that the optimum EBCT in the PBR was 8 hrs. The PBR with cell-immobilized pellets was effective as an advanced treatment process after an activated sludge process for treating dyeing wastewaters.