• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.33-40
• /
• 2021

Measuring the compressive strength of concrete is a very important factor in the safety review of concrete structures. Concrete compressive strength measurement methods include destructive and non-destructive methods. The destructive method includes the uniaxial compression failure method, and the non-destructive method includes the rebound hardness method and the elastic wave measurement method. In this study, the type of measurement method and the effect of reinforcing bars inside the concrete were tested to examine the relationship between them. Regardless of the type of specimen, the average compressive strength by the elastic wave measurement method among the three experimental methods was greater than the average compressive strength by the other methods. When the specimen type is the same, the standard deviation of the measured values of the elastic wave measurement method is smaller than that of the other measurement methods, so it can be seen that the elastic wave measurement method does not show large variance in the measured values compared to the other two measurement methods. When the average compressive strength according to the test method for each specimen was compared with the average compressive strength of the compressive failure test method, the average compressive strength was measured to be high in the order of the elastic wave measurement method, the compression failure test, and the rebound hardness method. Since the measured values of the compressive strength of concrete are different depending on the method of measuring the compressive strength of concrete and the presence or absence of reinforcing bars inside the concrete, further research is required considering the effect of various concrete covers.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.10
• /
• pp.113-120
• /
• 1995

여러가지 두꺼운 복합재료 구조물은 3차원 압축 부하 상태에 노출되는 경우가 발생한다. 이런 경우에 있어 서의 복합재료 압축 강도는 압축 평균 응력을 이용하면 예측이 가능할지도 모른다. 이번 연구 에서는 압축 평균 응력을 이용하여 탄소섬유 강화 복합재료들의 압축 강도를 예측하는 모델을 개발 하고자 한다. 이 모델은 압축강도에 영향을 주는 요소, 초기 misalignment를 고려하였고, 탄소섬유와 수지사이에 접합강도가 임계값을 초과할때 복합재료의 파괴가 일어난다고 가정한다. 또 여라가지 문헌들을 통하여 유압이 접합강도에 미치는 점들을 보여준다. 본 모델을 이용한 예측값들은 가해지는 유압에 따라 증가되며, 실험값들과 비교 분석될 것이다.

• Proceedings of the KSEG Conference
• /
• 2002.04a
• /
• pp.201-210
• /
• 2002

서울시 북동부의 서울화강암에 대한 암반 공학적 특성 중 터널과 도로 건설시 중요하게 취급되는 절리의 방향성, 절리간격, 절리밀도, 암석의 일축압축강도, 그리고 RQD 값을 수락산과 불암산지역으로 구분하여 비교, 분석하였다. 이 중 절리의 방향성, 절리간격과 절리밀도는 선조사법, 원형조사법, 그리고 면적조사법을 이용하여 야외에서 직접 측정하였다. 암석의 일축압축강도와 RQD의 측정은 시추코아의 표본이 필요하지만 이번 연구에서는 간단히 응용할 수 있는 대비공식을 이용하여 계산하였다. 측정된 대표적인 절리의 방향성은 두 지역에서 모두 3조의 방향성이 나타났으며 즉 2조의 수직정방절리와 저각으로 경사하는 1조의 판상절리로 판명되었으며 두 지역에서 서로 유사한 방향성을 갖는다. 측정된 절리밀도는 0.039-0.066/cm이었으며, 평균절리길이는 1.30-4.52m, 그리고 평균절리간격은 10.3cm에서 최대 59.6cm로 측정된 절리의 방향에 따라 변화가 심하다 또한 슈미트 해머 타격값에 근거한 절리면의 일축압축강도는 217 MPa에서 335 MPa로 매우 강한 암체였으며, 평균절리간격에 기초하여 계산된 이론적 RQD 값은 73.1-98.7%의 값을 갖는 것으로 나타났다.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.1
• /
• pp.119-124
• /
• 1998

콘크리트는 시멘트, 잔골재 및 굵은 골재, 물 및 첨가제의 양이나 투입순서 ,혼합방법등 여러 가지 요인에 따라 성질이 바뀌게 되는 복합재료이다. 따라서 넓은 의미에서 품질 판정의 한 수단이 되는 콘크리트의 설계기준강도 또는 압축강도 fc'(=28일 압축강도)는 물론 기타의 성질도 정확한 예측이 불가능하다. 즉 소요강도를 목표로 배합된 공시체의 시험결과는 예외없이 통계적 가변성을 나타낸다. 여기에서는 공시체의 7일 강도의 평균치 및 표준 편차와 공시체의 28일 강도 측정치로부터 콘크리트의 압축강도를 추정하는식을 제안하였다. 이를 위하여 7,320개의 강도시험자료를 수집한 후 이들을 선형 회귀 분석법으로 처리하였다. 제안된 식에 의한 콘크리트의 압축강도는 타 추정식에 의한 값보다 실측치에 좀 더 근접함을 보여주었다. 또한 제안식의 검정을 위해 서울지역 자료 5,200개를 수집하여 제안식과 JIS, Slater식과의 오차를 비교한 결과에 따르면 제안식이 더 안전측임을 알 수 있었다. 그리고 슈미트 햄머에 의한 현장 실측 강도와 제안식과의 콘크리트 강도 오차는 대체로 2.3%이었다.

• Journal of the Korea Concrete Institute
• /
• v.22 no.5
• /
• pp.659-666
• /
• 2010

Although the compression splice needs not be longer than the tension slice due to existence of end bearing, current design codes impose a longer compression lap splice than a tension lap splice in high strength concrete. Hence, new criteria for the compression lap splice including the effects of concrete strength need to be sought for economical design involving ultra-high strength concrete. An experimental study has been conducted with column specimens in concrete strength of 80 and 100 MPa. Test results show that the splice strength can be evaluated to be proportional to square root of compressive strength of concrete. Bar stress developed by end bearing is not affected by splice length and is expressed with a function of the square root of concrete strength. Mean value of stresses developed by end bearing is 16.5 square root of $f_{ck}$. The stresses developed by bond in compression splices are nearly identical to those in tension splices and, therefore, strength increment of compression splices is attributed to end bearing only. From regression analysis of 58 tests, a design equation is proposed for compression lap splice in 40 to 100 MPa of compressive strength of concrete. By the proposed equation, the anomaly of lap lengths in tension and compression is got rid of. In addition, the equation has a reliability equivalent to those of the specified strengths of materials.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.3
• /
• pp.273-291
• /
• 2020

The strength characteristics of the three orthogonal splitting planes, known as rift, grain and hardway planes in granite quarries, were examined. R, G and H specimens were obtained from the block samples of Jurassic granites in Geochang and Hapcheon areas. The directions of the long axes of these three specimens are perpendicular to each of the three planes. First, The chart, showing the scaling characteristics of three graphs related to the uniaxial compressive strengths of R, G and H specimens, were made. The graphs for the three specimens, along with the increase of strength, are arranged in the order of H < G < R. The angles of inclination of the graphs for the three specimens, suggesting the degree of uniformity of the texture within the specimen, were compared. The above angles for H specimens(θ^H, 24.0°~37.3°) are the lowest among the three specimens. Second, the scaling characteristics related to the three graphs of RG, GH and RH specimens, representing a combination of the mean compressive strengths of the two specimens, were derived. These three graphs, taking the various N-shaped forms, are arranged in the order of GH < RH < RG. Third, the correlation chart between the strength difference(Δσ_t) and the angle of inclination(θ) was made. The above two parameters show the correlation of the exponential function with an exponent(λ) of -0.003. In both granites, the angle of inclination(θ^RH) of the RH-graph is the lowest. Fourth, the six types of charts, showing the correlations among the three kinds of compressive strengths for the three specimens and the five parameters for the two sets of microcracks aligned parallel to the compressive load applied to each specimen, were made. From these charts for Geochang and Hapcheon granites, the mean value(0.877) of the correlation coefficients(R²) for total density(Lt), along with the frequency(N, 0.872) and density(ρ, 0.874), is the highest. In addition, the mean values(0.829) of correlation coefficients associated with the mean compressive strengths are more higher than the minimum(0.768) and maximum(0.804) compression strengths of three specimens. Fifth, the distributional characteristics of the Brazilian tensile strengths measured in directions parallel to the above two sets of microcracks in the three specimens from Geochang granite were derived. From the related chart, the three graphs for these tensile strengths corresponding to the R, G and H specimens show an order of H(R1+G1) < G(R2+H1) < R(R1+G1). The order of arrangement of the three graphs for the tensile strengths and that for the compressive strengths are mutually consistent. Therefore, the compressive strengths of the three specimens are proportional to the three types of tensile strengths. Sixth, the values of correlation coefficients, among the three tensile strengths corresponding to each cumulative number(N=1~10) from the above three graphs and the five parameters corresponding to each graph, were derived. The mean values of correlation coefficients for each parameter from the 10 correlation charts increase in the order of density(0.763) < total length(0.817) < frequency(0.839) < mean length(Lm, 0.901) ≤ median length(Lmed, 0.903). Seventh, the correlation charts among the compressive strengths and tensile strengths for the three specimens were made. The above correlation charts were divided into nine types based on the three kinds of compressive strengths and the five groups(A~E) of tensile strengths. From the related charts, as the tensile strength increases with the mean and maximum compressive strengths excluding the minimum compressive strength, the value of correlation coefficient increases rapidly.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.4
• /
• pp.385-392
• /
• 2014

The purpose of this study was to determine the effects of plantation thinning on physical and mechanical properties of Larix kaempferi. Tree samples were obtained from unthinned, moderately, heavily thinned plantations where located in Kwangryung forest research stand. The effects of different thinning methods on the bending and parallel to grain compressive strengths of Larix kaempferi were explored. Average latewood ratio with various thinning treatments revealed the trend of unthinning < moderate thinning < heavy thinning treatment. Average annual ring width with various thinning treatments showed the trend of unthinning < moderate thinning or heavy thinning treatment. Average bending and parallel to grain compressive strengths with various thinning treatments revealed the trend of unthinning > moderate thinning > heavy thinning treatment. This indicates that thinning treatment reduces average bending and parallel to grain compressive strength properties.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.4
• /
• pp.655-661
• /
• 2020

In this study, the correlation between concrete core compressive strength and rebound hardness of urban railway underground structures was analyzed. The equations for the range of rebound hardness were derived and compared with the measured concrete core strengths for each range of rebound hardness to confirm the adequacy of the estimated compressive strength. As the result, the linear regression analysis results of the average compressive strength by the Gaussian probability density function (representative compressive strength estimation formula) and the estimation formula by the rebound hardness range were founded to match well within 3% of the experimental concrete core compressive strength test results. Therefore, the stochastic statistical analysis using the rebound hardness measurement results suggested in this study could be help to secure the confidence level of the correlation between the rebound hardness and the concrete compressive strength which are relatively large deviation according to the estimation equations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.6
• /
• pp.132-140
• /
• 2019

In this study, a specimen composed of columns, walls, beams, and slabs was fabricated to investigate the estimated reliability using nondestructive test method for the location of structural members of reinforced concrete single layer structures. And for accurate analysis in the comparison process with the existing estimation formula, we try to analyze the reliability through statistical approach by using error rate comparison and Confidence interval estimation. As a result, The average error rate of the core test was 18.8% compared with the result of estimating the compressive strength using the ultrasonic pulse velocity method. The average error rate of the core test results compared with the result of estimating the compressive strength using the rebound hardness method was 20.1%, confirming the field applicability. it is judged that the reliability of the compressive strength estimation can be derived from the wall member to make a quick and efficient structure safety diagnosis using the ultrasonic pulse velocity method. In addition, it is judged that the reliability of the compressive strength estimation can be derived from the beam member to make a quick and efficient structure safety diagnosis using the rebound hardness method.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.7
• /
• pp.5-15
• /
• 2018

The unconfined compressive strength (UCS) test through coring is widely used to determine the reinforcement effect of the ground with grouting. However, the UCS test through coring can disturb the ground, is expensive and takes a lot of time to prepare the specimen. In this study, the factors affecting UCS of microfine cement grouted sand are evaluated and an empirical equation of UCS of microfine grouted sand is suggested. It is observed that UCS increases linearly until 28 days, however, the increasing rate of strength decreases sharply after that 28 days. The W/C ratio is dominant factor influencing UCS and UCS increases exponentially with the decrease of water/cement (W/C) ratio. Also, UCS increases linearly with increasing the relative density ranging from 30% to 70% and with decreasing median particle size. However, in case of W/C ratio=1 and K6 ($D_{50}=0.47mm$), UCS is lower than that of K4 ($D_{50}=1.08mm$) and K5 ($D_{50}=0.80mm$) due to filtration effect. Based on the experimental results, the empirical equation of UCS of microfine cement grouted sand can be expressed as the function of median particle size ($D_{50}$), porosity (n) and W/C ratio.