• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.171-181
• /
• 2003

The nose fairings of KSR-III are designed to be separated from the rocket by explosive force at the mission altitude to expose the payload. Adequate amount of separation force should be imposed to allow safe separation without collision between the fairings and the rocket, and the separation device was designed for the separation at very high altitude where almost no air load was expected. As the development of KSR-III goes on, several design changes have made and lower separation altitude of 45km is expected as a result. Under these circumstances, it is required to determine if the nose fairings can be separated without collision with much severer air load than for the design condition. In this study, the 6-DOF motion analysis program, PASEM, which was developed to predict the strap-on booster separation, is modified to simulate the pivotal motion of the fairings at early stages of separation. The accuracy of pivot motion simulation is validated by comparison with the results of ground test and the accurate separation conditions are deduced from it. Trajectory simulations are performed to see if separation without collision is possible with varying angle of attack, direction of gravity, and the effect of gust. It is also found that reducing the separation angle of the clamshell hinge from 60 degrees to 40 degrees can enhance separation safety and separation at lower altitude of 40km can be done without collision.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.351-363
• /
• 2020

Launch vehicles are subject to airborne acoustic loads during atmospheric flight and these effects become pronounced especially in transonic region. As the vibration due to the acoustic loads can cause malfunction of payloads, it is essential to predict and reduce the acoustic loads. In this study, a complete process has been developed for predicting airborne vibro-acoustic environment inside the payload pairing and subsequent noise reduction procedure employing acoustic blankets and Helmholtz resonators. Acoustic loads were predicted by Reynolds-Averaged Navier-Stokes (RANS) analysis and a semi-empirical model for pressure fluctuation inside turbulent boundary layer. Coupled vibro-acoustic analysis was performed using VA One SEA's Finite Element Statistical Energy Analysis (FE-SEA) hybrid module and ANSYS APDL. The process has been applied to a hammerhead launch vehicle to evaluate the effect of acoustic load reduction and accordingly to verify the effectiveness of the process. The presently developed process enables to obtain quick analysis result with reasonable accuracy and thus is expected to be useful in the initial design phase of a launch vehicle.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.117-122
• /
• 2008

Acoustic test was performed to verify the ability of KSLV-I PLF acoustic protection system (Acoustic blanket) to reduce the acoustic load. The test results showed that the acoustic protection system has +3 dB safety margin compared with design requirement. This paper also illustrates the increase of insertion loss by the acoustic protection system by comparing that of the bare PLF structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.12
• /
• pp.987-993
• /
• 2013

Korean Utility Helicopter(KUH) is the first korean-developed helicopter. Its first flight was performed in March 2010 and then its development was completed successfully by June 2012. During flight test phase, KUH faced various vibration problems and appropriate vibration-reduction devices were designed and applied to solve the problems. The vibration-reduction devices were applied to main rotor blades, main gear box(MGB) supporting structure, cockpit, cabin and pilot seats to reduce rotor-induced 4/rev vibration. Also, dome-fairing was introduced in order to reduce the tail-shake vibration. This paper shows design technique and flight test results for vibration-reduction devices that have been incorporated into KUH.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.150-161
• /
• 2005

A test was performed to collect the data to validate an analytic method for vent hole sizing on the nose fairing of a launch vehicle. The bake-out chamber at KARI was used to simulate the ambient pressure drop, and pressure difference data were collected for a model with various kinds of vent holes which was installed in the chamber. The characteristics of the test facility and measurement equipments were evaluated for the measurement of the transient behaviors. The measured data were processed in consideration of the characteristics of the facility and equipments, and the effects of vent hole size and configuration on the pressure variation in the model were analyzed based on the data.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.114-119
• /
• 2007

This paper introduces modal test of the 2nd stage structure of KSLV-I which is composed to satellite, PLA(Payload Adapter), EB(Equipment Bay), KMS(Kick Motor Support) and KM(Kick Motor) without PLF(Payload Fairing). In this test, to simulate free-free boundary condition, test object was hung by 4 bungee cords and excited by using impact hammer. From this test, dynamic properties of the 2nd stage structure of KSLV-I can be obtained. Modal test data are analyzed by using TDAS(Test Data Analysis Software). As the result, modal parameters and mode shapes below 100Hz of the 2nd stage of KSLV-I were identified.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.717-720
• /
• 2005

Acoustic loads generated by a rocket propulsion system cause severe random vibrations on payloads. In developing a new launch vehicle, a random vibration level must be specified before the detailed design of payloads or electronic equipments. This paper deals with prediction procedures of a random vibration level on payload section of KSLV-I. The prediction is based on statistical energy analysis. In order to verify the prediction methodology, test and analysis on a sub-scale payload section are performed. The predicted results subject to very high level of acoustic loads show a good agreement with the test results performed in the high intensity acoustic chamber. The predicted random vibration level on payload section of KSLV-I is also presented in this paper.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.9
• /
• pp.923-928
• /
• 2008

Pyrotechnic shock or pyroshock is characterized as a transient vibration phenomenon which shows large acceleration and high frequency range up to 10kHz during the operation of separation devices where explosives are used. During the flight of a launch vehicle, pyroshock is mainly generated at several events such as satellite separation, fairing separation and stage separation. In this paper, wiremesh isolators are introduced and several types of isolators are manufactured for the performance tests. For the investigation of typical characteristics of wiremesh isolators, compressive loading tests are basically performed and pyroshock tests are accomplished to confirm pyroshock isolation ability of each wiremesh isolator by using 4Kg dummy mass.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.3
• /
• pp.285-290
• /
• 2008

Pyrotechnic shock or pyroshock is characterized as a transient vibration phenomena which shows large acceleration and high frequency range up to 10kHz during the operation of separation devices where explosives are used. During the flight of a launch vehicle, pyro-shock is mainly generated at several events such as satellite separation, fairing separation and stage separation. In this paper, characteristics of pyroshock are introduced briefly, and PEEK washer shock absorber is applied for the reduction of pyroshock in the high frequency range. With some electronic devices, reduction characteristic of pyroshock using washer type shock absorber are studied. Random vibration tests are also performed for the verification of vibrational characteristics.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.73-73
• /
• 2003

인공위성은 발사체에 실려 임무궤도에 도달하는 동안 여러 과정을 겪고 이에 따른 우주 열환경에 노출되게 된다. 본 연구에서는 발사체의 페어링(Fairing)이 열리고 이후 인공위성이 임무궤도에 도달하는 동안까지 인공위성에 대한 열해석을 수치적인 방법을 이용하지 않고 해석해를 이용하여 수행하였다. 일반적으로 발사시 인공위성에 대한 열해석은 수치모델을 개발하여야 하는 시간과 노력이 많이 드는 작업이다. 그러나 수치 모델이 완성되기 전에 주요 부품에 대한 극한 환경에서의 온도 예측이 필요한 경우가 있다. 본 연구는 해석 기법을 이용하여 주요 부품의 온도를 비교적 간단한 방법으로 예측하는 것이다. 이를 위하여 열관련 지배방정식에 여러 가정을 적용하여 지배방정식을 최대한 단순화시켰다. 그 결과, 최종적으로 1차 미분 방정식 형태의 단순화된 지배방정식을 얻게 되었다. 또한 본 연구에서는 여러가지 조건에 대한 연구가 시도하였다. 즉 고려하는 대상의 질량이 일정하게 유지 되는 경우와 일정한 비율로 질량이 감소하는 경우, 인공위성이 최악의 고온환경과 최악의 저온환경에 처한 경우, 그리고 시간에 대한 변수항 때문에 약간의 수치작업이 필요한 경우가 연구되었다. 본 연구에서 제안된 해석해 기법은 적절한 우주 열환경 조건과 결합하게 되면 발사과정에 대한 완전한 수치모델이 완성되기전에 위성체 부품에 대한 열적 안정성을 검토하는데 유용하게 이용될 수 있을 것이다.