• Journal of Sensor Science and Technology
• /
• v.11 no.1
• /
• pp.60-65
• /
• 2002

$ZnGa_2O_4$ thin film phosphors have been deposited using a pulsed laser deposition method on Si(100) substrates at a substrate temperature of $550^{\circ}C$ with oxygen pressures of 100mTorr, and subsequently to investigate their photoluminescence characteristics after post-annealed at $600^{\circ}C$ and $700^{\circ}C$. As a result for X-ray diffraction, $Ga_2O_3$ shape appeared with increasing annealing temperature. The luminescent spectra show a broad band extending from 350 to 600nm peaking at 460nm. A post-annealing treatment of $ZnGa_2O_4$ thin films led to the different shape of luminescent intensity and grain size.

• Journal of Sensor Science and Technology
• /
• v.11 no.2
• /
• pp.118-123
• /
• 2002

$ZnGa_2O_4$ thin film phosphors have been deposited using a pulsed laser deposition technique on $Al_2O_3$(0001) substrates at a substrate temperature of $550^{\circ}C$ with various oxygen pressures 100, 200 and 300 mTorr. The films grown under different growth oxygen pressures have been characterized using microstructural and luminescent measurements. The different photoluminescence (PL) characteristics with the increase in oxygen pressures may result from the change of the crystallinity and the composition ratio of Zn and Ga in the films. The luminescent spectra show a broad band extending from 300 to 600 nm peaking at 460 nm. The PL brightness data obtained from the $ZnGa_2O_4$ films grown under optimized conditions have indicated that the sapphire is a promising substrate for the growth of high quality $ZnGa_2O_4$ thin film phosphor.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.6
• /
• pp.1067-1072
• /
• 2023

We prepared AZO (Al₂O₃ : 3 wt %) thin films according to the substrate temperature using the pulsed laser deposition method and the structural, electrical, and optical properties of the thin films were investigated. The AZO thin film deposited at 400℃ showed the best (002) orientation and the FWHM was 0.38°. As a result of the investigation of electrical properties, it was confirmed that the carrier concentration and mobility increased and the resistivity decreased as the substrate temperature increased. The average transmittance in the visible light region showed a high value of 85% or more regardless of the substrate temperature. The Burstein-Moss effect, in which the carrier concentration would increase with increasing substrate temperature thereby widening the energy band gap, was also observed. The resistivity and the figure of merit of the AZO thin film deposited at a substrate temperature of 400℃ were 6.77 × 10^-4 Ω·cm and 1.02 × 10⁴ Ω^-1·cm^-1 respectively, showing the best value.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.277-277
• /
• 2007

$(Bi,La)_4Ti_3O_{12}$ (BLT) 물질은 결정 방향에 따른 강한 이방성의 강유전 특성을 나타낸다. 따라서 BLT 박막을 이용하여 FeRAM 소자 등을 제작하기 위해서는 결정의 방향성을 세심하게 제어하는 것이 매우 중요하다. 현재까지 연구된 BLT 박막의 방향성 조절 결과를 보면, BLT 박막을 스핀 코팅 법 (spin coating method)으로 중착하고, 핵생성 열처리 단계를 조절하여 무작위 방향성 (random orientation)을 갖는 박막을 제조하는 방법이 일반적이었다. 그런데 이러한 스핀 코팅법에서의 핵생성 단계의 제어는 공정 조건 확보가 너무 어려운 단점이 있다. 이러한 어려움을 극복할 수 있는 대안은 스퍼터링 증착법 (sputtering deposition method), PLD법 (pulsed laser deposition method) 등과 같은 PVD (physical vapor deposition) 법의 증착방법을 적용하는 것이다. PVD 법으로 증착하는 경우에는 이미 박막 내에 무수한 결정핵이 존재하기 때문에 핵생성 단계가 필요 없게 된다. PVD 증착법의 적용을 위해서는 타겟 (target)의 제조 및 평가 실험이 선행되어야 한다. 그런데 벌크 BLT 재료의 소결공정 조건과 전기적 특성에 관한 연구 결과는 거의 발표 되지 않고 있다. 본 실험에서는 $Bi_2O_3$, $TiO_2$ and $La_2O_3$ 분말을 이용하여 최적의 조성을 구하기 위하여 Bi양을 변화시키며 타겟을 제조 하였다. 혼합된 분말을 하소 후 pallet 형태로 성형하여 소결을 실시하였다. 시편을 1mm 두께로 연마하고, 표면에 silver 전극을 인쇄하여 전기적 특성을 측정하였다. Bi양이 3.28몰 첨가된 조성에서 최대의 잔류분극 (2Pr) 값을 얻었고, 이때의 값은 약 $18{\mu}C/cm^2$ 정도였다. 최적화된 조성 ($Bi_{3.28}La_{0.75}Ti_3O_{12}$)으로 BLT 타겟을 제조하여 PLD법으로 박막을 제조하였다. 박막 제조 시 압력은 $1{\times}10^{-1}\;{\sim}\;1{\times}10^{-4}\;Torr$ 범위에서 변화시켰다. $1{\times}10^{-1}\;Torr$ 압력을 제외하고는 모든 압력에서 BLT 박막이 증착되었다. 중착된 박막을 $650\;{\sim}\;800^{\circ}C$에서 30분간 열처리를 실시하고 전기적 특성을 평가한 결과, $1{\times}10^{-2}\;Torr$에서 증착한 박막에서 양호한 P-V (polarization-voltage) 이력곡선을 얻을 수 있었고, 이때의 잔류분극 (2Pr) 값은 약 $6\;{\mu}C/cm^2$ 이었다. 주사전자현미경 (SEM)을 이용하여 BLT 박막 표면의 미세구조도 관찰하였는데, 스핀코팅 법으로 증착한 경우에 관찰되었던 조대화된 입자들은 관찰되지 않았고, 상당히 양호한 입자 크기 균일도를 나타내었다.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.342-346
• /
• 2004

Recently there has been a great world-wide interest in developing and characterizing new nano-structured materials. These newly developed materials are often prepared in limited quantities and shapes unsuitable for the extensive mechanical testing. The development of depth sensing indentation methods have introduced the advantage of load and depth measurement during the indentation cycle. In the present work, ZnO thin films are prepared on the Glass, GaAs(100), Si(111), and Si(100) substrates at different temperatures by pulsed laser deposition(PLD) method. Because the potential energy in c-axis is law, the films always shaw c-axis orientation at the optimized conditions in spite of the different substrates. Thin films are investigated by X-ray diffractometer and Nano indentation equipment. From these measurements it is possible to get elastic modulus and hardness of ZnO thin films on all substrates.

• Transactions of Materials Processing
• /
• v.29 no.1
• /
• pp.44-48
• /
• 2020

Aluminum nitride (AlN), as a substrate material in electronic packaging, has attracted considerable attention over the last few decades because of its excellent properties, which include high thermal conductivity, a coefficient of thermal expansion that matches well with that of silicon, and a moderately low dielectric constant. AlN films with c-axis orientation and thermal conductivity characteristics were deposited by using Pulsed Laser Deposition (PLD). The epitaxial AlN films were grown on sapphire (c-Al₂O₃) single crystals by PLD with AlN target and Y₂O₃ doped AlN target. A comparison of different targets associated with AlN films deposited by PLD was presented with particular emphasis on thermal conductivity properties. The quality of AlN films was found to strongly depend on the growth temperature that was exerted during deposition. AlN thin films deposited using Y₂O₃-AlN targets doped with sintering additives showed relatively higher thermal conductivity than while using pure AlN targets. AlN thin films deposited at 600℃ were confirmed to have highly c-axis orientation and thermal conductivity of 39.413 W/mK.

• Korean Journal of Materials Research
• /
• v.15 no.5
• /
• pp.293-300
• /
• 2005

ZnO:Li epilayers were synthesized on sapphire substrates by the pulesd laser deposition (PLD) after the surface of the ZnO:Li sintered pellet was irradiated by the ArF (193 nm) excimer laser. The growth temperature was fixed at $400^{\circ}C$. The crystalline structure of epilayers was investigated by the photoluminescence (PL) and double crystal X-ray diffraction (DCXD). The carrier density and mobility of epilayers measured by van der Pauw-Hall method are $2.69\times10cm^{-3}$ and $52.137cm^2/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of epilayers obtained from the absorption spectra is well described by the Varshni's relation, $E_g(T)=3.5128eV{\cdot}(9.51\times10^{-4}eV/K)T^2/(T+280K)$. After the as-grown ZnO:Li epilayer was annealed in Zn atmospheres, oxygen and vaccum the origin of point defects of ZnO:Li has been investigated by PL at 10 K. The Peaks of native defects of $V_{zn},\;V_o,\;Zn_{int},\;and\;O_{int}$ showned on PL spectrum are classified as a donors or accepters type. We confirm that $ZnO:Li/Al_2O_3$ in vacuum do not form the native defects because ZnO:Li epilayers in vacuum existe in the form of stable bonds.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.2
• /
• pp.108-111
• /
• 2011

The semiconducting material of ZnO in II-VI group was well known as its good application for photo electronics, chemical sensors and field effect transistors due to the remarkable optical properties with wide energy band gap and great ionic reactivities. Up to now the growth of a good quality of ZnO film has been issued for better performances. Even though there were many deposition methods for making ZnO films, pulse laser deposition methods have been preferred for high crystalline films. In this report, the ZnO film was also created by pulsed laser deposition technique which also showed high crystalinity. By controlling several factors when deposited, it was investigated that the optimal condition for ZnO film formation. Mainly, oxygen partial pressures and growth temperatures were changed when ZnO films were synthesized and followed the characterization by HRXRD and AFM.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.115-119
• /
• 1999

Ba$_2Cu_3O_{7-{\delta}}$ (YBCO) thin films were deposited by pulsed laser deposition using differently prepared targets: One was a conventionally solid-state sintered (SSS) target and the other was a modified melt-textured grown (MTC) target. Compared with SSS targets, MTG targets showed a well-connected microstructure consisting of much larger grains and the surface was Bess roughened with the cumulative laser incidence. YBCO films deposited from MTC targets showed a denser and smoother surface of the basal film than the case of SSS targets. The investigations of ${\alpha}$-axis outgrowths in the films indicated that the deposition using MTG targets would result in a more homogeneous and stable film growth as compared to the SSS targets. Also, TEM analysis revealed that the film deposited from MTG targets had a less granular microstructure that would reduce weak-link effects in the film.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.1 s.34
• /
• pp.73-76
• /
• 2005

To widen the band gap of ZnO, we have investigated $Zn_{1-x}Mg_xO(ZMO)$ thin films prepared by pulsed laser deposition on c-plane sapphire substrates at $500^{\circ}C$. From X-ray diffraction patterns, ZMO films show only the (0002) and (0004) diffraction peaks. It means that the flints have the wurtzite structure. Segregation of ZnO and MgO phases is found in the films with x=0.59. All the samples are highly transparent in the visible region and have a sharp absorption edge in the UV region. The shift of absorption edge to higher energy is observed in the films with higher Mg composition. The excitonic nature of the films is clearly appeared in the spectra for all alloy compositions. The optical band-gap ($E_g$) of ZMO films is obtained from the ${\alpha}^2$ vs Photon energy plot assuming ${\alpha}^2\;\propto$ (hv - $E_g$), where u is the absorption coefficient and hv is the photon energy. The value of $E_g$ increases up to 3.72 eV for the films with x=0.35. It is important to adjust Mg composition control for controlling the band-gap of ZMO films.