• Tribology and Lubricants
• /
• v.10 no.2
• /
• pp.1-4
• /
• 1994

금속과 금속이 접합할 때 발생하는 고유 저항값은 접촉소재의 종류, 접촉면의 상태, 접촉조건(하중, 온도, 정적 또는 동적인 접촉 등), 주변환경에 따라서 변한다. 소재가 접촉할 때 발생되는 저항값의 변화특성을 적극적으로 이용한 것이 전기 저항법(Electrical Contact Resistance Method)이다. 접촉 저항법의 특징은 접촉시 발생되는 저항값이 미세하게 변화한다 할지라도 모두 계측이 가능하다는 점이다. 그동안의 연구는 ㅈ로 단일 접촉점(Single Contact Spots) 위주의 단편적인 실험적 연구를 통하여 접촉 저항법에 대한 신뢰도 확보에 노력하였으나, 최근에는 접촉점이 인접한 다른 접촉부위에 미치는 영향, 즉 다수 접촉점군(Multiple Contact Spots and Clusters)의 거동해석에 더욱 큰 연구 비중을 두고 있다. 접촉점군 상호간의 영향에 관한 연구가 많이 진행되기는 하였지만 해석모델의 적절성 여부가 실험적 데이타를 통하여 확인이 아직 안되었기 때문에 기존의 접촉저항 추정식을 직접 사용하기가 어려웠으나 최근에 볼군-원판 모델에 대한 접촉점과 다수의 접촉점군 상호간에 발생될 수 있는 접촉저항 특성을 실험적으로 해석하여 보다 정확한 해석모델이 제시되었다.

• Tribology and Lubricants
• /
• v.26 no.5
• /
• pp.272-276
• /
• 2010

Aminated oilve oil derivative as the new organic disperse phases of the water soluble metal working fluid has been synthesized and tribological properties of the aqueous solutions composed of aminated olive oil derivative investigated using Four Ball Wear Tester and Falex EP Tester. The formulated aqueous solutions showed higher antiwear and extreme pressure properties and also lower friction coefficient. On the basis of the the results, water soluble aminated oilve oil derivative showed excellent tribological properties due to the polarizability of oleic acid derivative composed of majority part in oilve oil.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.196-202
• /
• 2006

This paper presents a case study on the tribological failure analysis of a clutch system for a manual transmission car. The clutch systems are composed of clutch disk, clutch pressure plate, flywheel rubbing surface, coil and diaphragm springs, release bearing and lever, clutch spline and shaft. The purpose of a clutch system is to transmit and disconnect the driving power of engines by frictional farce from a rubbing surface of a flywheel to a clutch disk and clutch pressure plate with a minimum power loss. In this study, many tribological failure cases based on the wear phenomena and thermal distortions have been presented, which are collected from the car repair shop and maintenance center. The triboiogicai failures are mostly come from the driving conditions, overloading of a car, and especially driving style and personal habit of a car driver.

• Tribology and Lubricants
• /
• v.19 no.2
• /
• pp.109-115
• /
• 2003

Nanotribological characteristics between a Si$_3$N$_4$ AFM tip and hydrophobic thin films were experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM (atomic force microscope) and LFM (lateral force microscope) modes in various .ranges of normal load. Plasma-modified thin polymeric films were deposited on Si-wafer (100). Results showed that wetting angle of plasma-modified thin polymeric film increased with the treating time, which resulted in the hydrophobic surface and the decrease of adhesion and friction. Nanotribological characteristics of these surfaces were compared with those of other hydrophobic surfaces, such as DLC, OTS and IBAD-Ag coated surfaces. Those of OTS coated surface were superior to those of others, though wetting angle of plasma-modified thin polymeric film is higher.

• Tribology and Lubricants
• /
• v.18 no.6
• /
• pp.377-383
• /
• 2002

The tribological role of mass transfer layer was studied with silver coatings under various ranges of load and sliding speed. Silver coating was performed with a functionally gradient coating method. Tests were per-formed in dry sliding conditions, using a ball-on-disk contact configuration, at the load of 0.0196-17.64 N and the sliding speed of 20-1,000 mm/s in ambient air. Optical microscope and EPMA analyses showed that contact surfaces were covered with the mass transfer layers of agglomerated wear particles depending upon the contact conditions, and they greatly influenced the tribological characteristics of the surfaces. However, the formation of mass transfer layer was suppressed as the sliding speed increased, and above a critical sliding speed, no mass transfer layer was able to form. For building up a general framework of triboiogical behavior of the coated silver films, all test data were summarized on a map whose axes are contact pressure and sliding speed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.210-217
• /
• 1997

This paper presents the numerical results of the stress analysis of wheel-rail contact problems. Two models which have straight and tapered(1:20) contact geometries between the wheelset and rail are analyzed using the finite element approach. From the simulation results we found that the tapered geometry of wheel-rail contact base line showed very stable contact stress distributions for a whole contact position between the wheel and rail in a curved rail section. The FEM computed results may present an optimized geometry of wheel-rail contact in a high-speed railway system.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1990.06a
• /
• pp.45-52
• /
• 1990

고도의 신뢰도를 요구하는 정밀기계의 보편화는 트라이볼로지 요소중에서 밀봉기능에 관련된 시일의 해석 및 설계가 커다란 관심사로 부각되었다. 특히 고속회전을 요하는 경우에 대한 회전 시스템의 동적 안정성은 대단히 중요하다. 미끄럼 접촉운동을 하고 있는 기계평면시일의 시일링 간극은 대단히 작기 때문에 시일의 접촉면에서 형상이 변화하게 되면 시일 성능은 커다란 영향을 받게 된다. 시일의 접촉표면 가공시 발생되는 평면도(flatness), 조립시의 회전축과 시일축 사이의 중심 맞추기의 어려움, 회전축의 자중량 등 때문에 발생되는 회전링 사이의 상대적인 경사도(misalignment)는 시일의 동적 불안정성에 영향을 준다. 또한 상대 접촉 운동면에서 경계 또는 고체 마찰에 의한 마멸의 진행은 시일의 코닝(coning) 현상을 일으킨다. 본 연구에서는 비압축성 유체가 온도의 영향을 받아 점도가 선형적으로 변화하는 경우에 대한 시일링 간극 내에서의 압력분포를 유한차분법을 이용하여 해석하였다. 여기서 얻어진 결과를 이용하여 시일의 축력과 모우멘트를 해석함으로써 시일의 동적 불안정성에 대하여 논하였다. 이 때 기계평면 시일의 형상은 코닝이 있고, 시일의 중심축이 경사진 경우를 고려하였다.

• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.45-53
• /
• 1998

Friction and wear test for two kinds of Cu-based sintered metallic friction material against cast iron disk was carried out by plate-on-disk type friction and wear tester to investigate the friction and wear characteristics of brake system in severe condition. In this experimental study, the counter specimen was cast iron which is being used generally in brakes of heavy duty equipments. Test friction materials were A type which was manufactured by foreign company and B type by domestic company. Friction coefficient and wear volume were measured and compared with each other. The experiment was performed under room temperature. The worn surface of cast iron disk and friction material were observed by scanning electron microscope. The temperature of surface of disk was measured continuously by the non-contacting thermometer. It was found that A type friction material had stable friction coefficient over the wide range of sliding condition, but B type friction material had unstable friction coefficient and lower value of 0.2 under the severe sliding condition.

• Tribology and Lubricants
• /
• v.23 no.1
• /
• pp.19-28
• /
• 2007

Mechanical Brake system is inevitable equipment for stability of train and speed of the train. Especially brake disk and brake pads are core parts of mechanical brake system. It was investigated with tribological characteristics of brake discs for train by using lab-scale dynamometer. Gray cast iron disk was most attacked with sintered brake pad. Alloyed steel disk and NCM cast iron disk had suitable friction coefficient, high stability and low disk attack to the sintered brake pad. But at the view of economy, low alloyed cast iron will be most suitable choice.

• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.1-12
• /
• 1994

PTFE(Polytetrafluoroethylene)은 매우 낮은 마찰계수를 나타내고, -260부터 +260$\circ$C의 온도에서 계속적으로 사용할 수 있는 유용한 기계적 성질들을 유지한다. 결정 용융점은 327$\circ$C로서, 대부분의 다른 준결정(semicrystalline) 복합 재료들 보다 훨씬 높다. 더욱이, PTFE는 응력 상태에서 냉간 유동성을 보이며, 준결정 고분자들 중에서 가장 높은 마모율을 보인다. 하지만, 이러한 단점들은 PTFE내에 충전재(filler)를 첨가함으로써 매우 향상될 수 있다. PTFE의 독특한 특성의 하나는 충전재가 함유될 때의 내마모성의 증가가 다른 준결정 고분자보다 대단히 큰 것이다. 위에서 언급된 특성으로 인하여, PTFE는 마찰에 응용되는 고분자계 복합 재료들 중에서 매우 중요한 메트릭스 고분자이다. PTFE의 독특한 트라이볼로지적 성질들은 고유의 분자적 그리고 형태적 구조에 기인한다.