• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.6
• /
• pp.691-698
• /
• 2014

This paper describes the manufacturing processes for a flexbeam and torque tube made of composite materials, along with the procedures for testing their basic properties. A flexbeam and torque tube can be considered to be key structural components of a bearingless rotor hub system. A hinge offset effect can be realized by a large elastic deformation and twist of the flexbeam, and the blade pitch control forces are transferred by the rotation of the torque tube. The basic property tests included bending and twist tests to determine the flap stiffness, lag stiffness, and torsion stiffness of the flexbeam, torque tube, and blade, and these tests were performed prior to starting the whirl tower test. In addition, the estimated results were compared with experimental data, and the calculations were found to be a good match for the analysis results and had a similar tendency. Through these results, we could confirm that a flexbeam and torque tube made of composite materials satisfied the structural stiffness requirements.

• Composites Research
• /
• v.19 no.3
• /
• pp.29-36
• /
• 2006

Since composite materials have anisotropic properties that depend on their stacking angle and sequence, the analysis of joints with isotropic adherends is limited in describing the behavior of the adhesive Joint with composite adherends. In this study, the nonlinear solution for adhesive joints with composite adherends was derived by incorporating the nonlinear behavior of the adhesive into the analysis. The behavior of the laminated composite tube was first analyzed, and the stress distributions of the composite tubular adhesive joint were calculated by including the nonlinear properties of the adhesive. The effect of the stacking sequence of composite adherends and bonding length on torque capacities of joints was examined, and results of the nonlinear analysis were also compared with those of the linear analysis.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.6
• /
• pp.484-491
• /
• 2016

The purpose of this development is weight reduction of hollow type steel torque bar by changing the material from steel to composite. Structure analysis is executed by the finite element model generated by the structural load condition and geometric structure requirement. According to this analysis result, optimized ply sequence and wall thickness are defined. To simulate analysis result, torsion test for composite torque bar was performed. Throughout the test result, the stiffness and strength requirement of composite torque bar was verified.

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.10-19
• /
• 2014

We designed bearingless rotor hub system which replace mechanical hinge/bearing with composite beam component and conducted fatigue analysis for flexbeam and torque tube. Extension/bending/torsional stiffness was calculated from 2D section analysis using VABS and 2D section structure analysis was applied for strain calculation. S-N curve of each composite material was generated using Wohler equation and fatigue analysis was conducted on weakness section which was decided from static structure analysis. CAMRAD II was used for load analysis and load analysis result was applied HELIX/FELIX standard load spectrum to generate bearingless rotor system load spectrum which was used fatigue safe life analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.12
• /
• pp.5393-5397
• /
• 2011

The compressing-cutting device is used for manufacturing nano tube. the purpose of this study is to design and manufacture the compressing-cutting device witch has safety and stable performance. The most important core technology, in nano tube manufacturing, is to seam the each end of tube with appropriate pressure and to cut it off into the two part safely not to leak injected medium. Since the compressing pressure and the cutoff speed make the quality of nano tube, they are very important. This study will show the processes of design and manufacturing of compressing-cutting device.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.52-56
• /
• 2011

Recently, KARI(Korea Aerospace Research Institute) has been developing a modern 11.5m diameter four bladed bearingless main rotor system, and this rotor system can be used for 7,000lb class helicopter. Flexbeam and torque tube can be considered as the key structural components, and large elastic twist of flexbeam induced by pitch control motion of torque tube can influence the nonlinear aeroelastic behavior. In this paper, the dynamic characteristic analysis results of bearingless rotor system were presented. In order to construct a input model and validate the analysis procedures, calculated results using the comprehensive helicopter analysis program CAMRAD II were compared with the measured natural frequencies and lag damping data from small-scale wind tunnel test. Next, the analysis model was extended to a full-scale model, and the dynamic analysis results were presented.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.2
• /
• pp.187-192
• /
• 2012

Recently, KARI(Korea Aerospace Research Institute) has been developing a modern 11.5 m diameter four bladed bearingless main rotor system, and this rotor system can be used for 7,000 lb class helicopter. Flexbeam and torque tube can be considered as key structural components, and large elastic twist of flexbeam induced by pitch control motion of torque tube can influence the nonlinear aeroelastic behavior. In this paper, the dynamic characteristic analysis results of bearingless rotor system were presented. In order to construct a input model and validate the analysis procedures, calculated results using the comprehensive helicopter analysis program CAMRAD II were compared with the measured natural frequencies and lag damping data from small-scale wind tunnel test. Next, the analysis model was extended to a full-scale model, and the dynamic analysis results were presented.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.29-35
• /
• 2011

The behaviors of combustion-induced internal flows of SRM equipped with fin-slot grain and submerged nozzle are very complex and diverse. Cold air-flow tests for 2D and 3D scale models of SRM have been done in order to specify the visualization method to analyze particular internal flow patterns such as roll-torque inducing flow. Swirl flow induced by asymmetric vortical tubes also has been visualized through employing various light source and recording directions.

• Journal of the Korea Convergence Society
• /
• v.11 no.2
• /
• pp.167-174
• /
• 2020

The social statistic was used to top 250 Korean and Japanese YouTube channels based on the number of subscribers examine its channel type (private/corporations/others), distribution of contents and private YouTube channels' date of registration. The channel examination was also used to provide practical hint to create new Youtube contents. According to the statistics, Korean channels were mainly managed by K-Culture related companies for the promotional purpose, whereas Japanese channels were mainly managed by individuals with a variety of contents. It is presumed that Japanese individuals have been engaged in creating individual video content since the early period through video uploading platforms other than YouTube such as Niconico Douga. Since the expansion of the YouTube market will continue, it is important not only to reinforce corporations' marketing on YouTube but also to promote the uniqueness and the diversity of YouTube content for the individuals to improve the economical, sentimental, and informational contents in order to create socially effective personal contents that can be competitive in the global market.

• Journal of the Korean Society for Library and Information Science
• /
• v.55 no.4
• /
• pp.187-217
• /
• 2021

This study investigated the perceptions of librarians about Podcast and YouTube services in libraries. The study was designed by applying the Extended Technology Acceptance Model. Librarian's personal, organizational, and social awareness of library Podcast or YouTube services and the degree of understanding of users and their needs on services were mediated by perceived usefulness or ease of services= and influenced to having intentions and providing the services. First, we investigated the types of Podcast and YouTueb services provided by 39 libraries in Korea. Also, we collected data using an online survey method from 181 librarians and conducted hierarchical multiple regression analysis. Findings showed that libraries are using Podcast and YouTube appropriately considering features and functions of media, mainly for library event information/promotion, library programs, book recommendations, and author (librarian) lectures or interviews. Organizational or social awareness of librarians, i.e., library educational support, human resource supports, librarian recognition, job-related features, and understanding of user perceptions and needs, influenced the intention to provide library services. Also, there was a difference in perceived usefulness and ease of services between librarians who provided Podcast and YouTube services and those who did not. We expect that findings could be used as references to understand and support various aspects of librarians in charge of developing and providing Podcast or YouTube services in libraries.