• Journal of Powder Materials
• /
• v.22 no.5
• /
• pp.350-355
• /
• 2015

Perforated polygonal cobalt oxide ($Co_3O_4$) is synthesized using electrospinning and a hydrothermal method followed by the removal of a carbon nanofiber (CNF) template. To investigate their formation mechanism, thermogravimetric analysis, field-emission scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy are examined. To obtain the optimum condition of perforated polygonal $Co_3O_4$, we prepare three different weight ratios of the Co precursor and the CNF template: sample A (Co precursor:CNF template- 10:1), sample B (Co precursor:CNF template-3.2:1), and sample C (Co precursor:CNF template-2:1). Among them, sample A exhibits the perforated polygonal $Co_3O_4$ with a thin carbon layer (5.7-6.2 nm) owing to the removal of CNF template. However, sample B and sample C synthesized perforated round $Co_3O_4$ and destroyed $Co_3O_4$ powders, respectively, due to a decreased amount of Co precursor. The increased amount of the CNF template prevents the formation of polygonal $Co_3O_4$. For sample A, the optimized weight ratio of the Co precursor and CNF template may be related to the successful formation of perforated polygonal $Co_3O_4$. Thus, perforated polygonal $Co_3O_4$ can be applied to electrode materials of energy storage devices such as lithium ion batteries, supercapacitors, and fuel cells.

• Journal of the Korean Vacuum Society
• /
• v.15 no.5
• /
• pp.499-505
• /
• 2006

Field emission of GaN and GaP nanowires, synthesized by thermal chemical vapor deposition, and their emission stabilities under oxygen and argon environments were investigated. The field emission current of GaN nanowires was seriously deteriorated under oxygen environment, while that of GaP was not. Both wires did not show any noticeable change under argon environment. The existence of oxide outer shell layers in the GaP nanowires was proposed to be a main reason for this emission stability behavior. Field emission energy distributions of electrons from these nanowires revealed that field emission mechanism of the semiconductor nanowires were different from that of carbon nanotubes.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.2
• /
• pp.297-305
• /
• 2016

This study aims to analyze characteristics of environmental load for the construction phase of PSC beam bridge based on Life Cycle Assessment. For detail computation of environmental load, the construction materials and energy consumption are derived from the BOQ, also connecting with environmental load by Korea LCI Database Information Network. The characteristic of environmental impact was analyzed by 25 cases and cut-off ratio was 80% to 94%. The result sorted by construction materials revealed that environmental load were 53.3% for ready-mixed concrete, 9.6% for wire rod, 7.8% for rebar, 6.8% for cement, 5.5% for plywood, and 5.2% for energy. Furthermore, the result of environmental impact revealed that 45.5% for global warming, 30.4% for abiotic resources depletion, 10.5% for human toxicity, and 8.9% for photochemical oxidant creation. In the future, we can make a decision considering environmental load based on LCA at design phase.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.386.2-386.2
• /
• 2014

본 연구에서는 바이오 센서 응용을 위해 그래핀을 전극으로 제작하여 그래핀 표면 결함준위에 따른 센서의 민감도를 전기화학 실험을 통해 관찰하였다. 그래핀은 니켈/구리촉매를 이용한 저 진공 화학 기상 증착 장비(Low-Pressure Chemical Vapor Deposition; LP-CVD)와 Photo-lithography로 제작한 것과 탄소 산화물을 환원시켜 만든 환원-그래핀, 두 가지를 사용하였다. 전기화학 실험에서 그래핀 전극 및 Silver/Silver chloride (Ag/AgCl), Fluorine doped Tin Oxide (FTO)은 작업 전극 및 기준 전극, 상대 전극으로 각각 사용하였고, 반응용액은 potassium hexacyanoferrate (III)를 농도를 다르게 하여 사용하였다. 그래핀의 표면 상태, 층수, 결함 정도 등 구조적인 특성은 원자력현미경(Atomic Force Microscopy; AFM), 주사 전자 현미경(Secondary Electron Microscopy; SEM)과 Raman spectroscopy를 각각 이용하여 확인하였고, 그래핀의 결함준위에 따른 반응면적 및 센서 감도 의존성을 전류모드-원자력현미경(Current-Atomic Force Microscopy; I-AFM)과 전기화학 임피던스 분광법(Electrochemical Impedance Spectroscopy; EIS)를 통해 그래핀 전극의 성능을 분석하고, 그래핀 결함 준위에 따른 센서 감도 의존성은 순환전위 분광법 (Cyclic Voltammetry; CV)를 이용하여 관찰하였다. 또한 농도가 다른 반응용액은 센서의 민감도를 관찰하는데 사용하였다. 결과적으로 LP-CVD로 성장한 그래핀과 환원-그래핀의 결함준위에 따른 센서의 성능을 비교 분석한 결과와 반응용액 농도에 따른 센서의 민감도 결과는 그래핀 바이오센서에 대한 응용 및 상용화를 앞당기는데 기여할 것으로 예상한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.3
• /
• pp.219-224
• /
• 2017

A study on dissimilar friction-welded joints was performed for cam shaft applications using solid bar samples, 20mm in diameter, of forging steel(SF45) and carbon steel(SM45C). The main parameters of friction welding such as tensile tests, Vickers hardness surveys of the bond of area, the heat affected zone (HAZ), and the observation of microstructure were investigated to ensure a good quality of friction welding through visual observations. The specimens were tested as-welded and post weld heat treatment(PWHT). This paper deals with optimizing the welding conditions and analyzing various rotary bending fatigue test(RBFT) properties about heat-treated base metal(BM), as-welded and PWHT. Consequently, two materials for friction welding are strongly mixed with a well-combined structure of micro-particles without any molten material, particle growth, or any defect. Moreover, the fatigue limit of BM(SF45) and PWHT for the RBFT were observed as 180MPa and 250MPa, respectively. It was confirmed that the PWHT causes approximately 40％ improvement in the fatigue limit when compared to the BM(SF45).

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.207-214
• /
• 1990

The catalytic reaction between CO and NO on polycrystalline Pt surface, which is very important in the development of catalyst for automobile exhaust gas control, has been studied using thermal desorption spectrometry(TDS) and steady-state experiment under ultra-high vacuum(UHV) conditions. With the pressures of CO and NO of each $1{\times}10^{-7}Torr$, the $CO_2$ formation rate showed a maximum at 560K. At the reaction temperature of 560K and the NO pressure of $1{\times}10^{-7}Torr$, the production of $CO_2$ was first order in $CO_2$ was first order in CO pressure below $1.35{\times}10^{-7}Torr$ of CO pressure whereas at higher CO pressures the rate became minus 0.3 order in CO. But the efforts of reactant pressure on the reaction was understood in consideration of the surface concentrations of adsorbates. With the results, we proposed a new reaction mechanism for this reaction.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.1
• /
• pp.11-19
• /
• 2003

A micro sensor array with 4 discrete sensors integrated on a microhotplate was developed for identifying the kinds and quantities of explosive gases. The sensor array consisited of four tin oxide-based thin films with the high and broad sensitivity to the tested explosive gases and uniform thermal distribution on the plate. The microhotplate, using silicon substrate with N/O/N membrane, dangling in air by Al bonding wires, and controlling the thickness by chemical mechanical process (CMP), has been designed and fabricated. By employing the sensitivity signal of the sensor array at 40$0^{\circ}C$, we could reliably classily the kinds and quantities of the explosive gases like butan, propane, LPG, and carbon monoxide within the range of threshold limit values (TLVs), employing principal component analysis (PCA).

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.241-248
• /
• 2003

We controlled the amount of Y$_2$O$_3$additives, 8 mol% and 10 mol%, and the type of carbon pore former, activated carbon and carbon black, to improve the strength of porous NiO-YSZ anode materials for solid oxide fuel ceil. The 3-point flexural strength, porosity and electrical conductivity were evaluated. As a result, the strength of anode materials with the addition of carbon black was markedly improved. The strength of NiO-10 mol%YSZ sintered at relatively higher temperature was higher than that of NiO-8 mol%YSZ materials. The electrical conductivity of NiO-10 mol%YSZ with carbon black was evaluated as much as 10$^2$∼10$^3$S/cm at 700$^{\circ}C$∼1000$^{\circ}C$ in reducing atmosphere.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.27-32
• /
• 2010

To improve electronic conductivity of cathodic active materials of lithium ion battery, carbonaceous materials is usually added. New mixing method of abrasive milling has been investigated in mixing of graphite and $LiCoO_2$ powders. It would be expected that uniform mixing of graphite reduces capacity fading of cathode of lithium battery. Abrasion milled $LiCoO_2$ composite showed the best electrochemical performance as a cathode material with 1 wt% of graphite content, 300 rpm of milling speed, and 10 min of milling time. The improvement of the electrochemical performances such as cycleability and charge/discharge capacity retention would be mainly attributed to increase of the electronic conductivity and/or prevention of the active materials by uniform dispersion and coating of graphite on $LiCoO_2$.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.283-283
• /
• 2021

혼합대는 지표수와 지하수의 수리적 교환이 일어나는 경계부로써 1) 수문학적 관점에서는 하도와 하상간의 물교환이 이루어지는 공간으로 다양한 물리적·화학적 작용이 발생, 2) 생지화학적인 관점에서는 하상 간극수 흐름에 의한 전이대(ecotone)를 형성하여 용존산소·영양물질·용존유기탄소의 이동뿐만이 아니라 지하수로부터 열에너지·무기염류의 공급을 유도하면서 높은 생지화학적 활동과 변환을 야기하는 산화·환원 반응구역, 3) 생태적인 관점에서는 저서생물과 지하 유기체종을 특징으로 하는 서식지이나 잠재적인 레퓨지움(refugium) 등의 관점에서 해석될 수 있다. 국내 하천환경의 생태학적 지속가능성을 위한 지표수-지하수 혼합대 관리에 대한 중요성이 점차 증대되고 있지만 우리나라는 여전히 지하수의 이용 및 보전과 지하수의 안정적인 수량·수질 확보를 목표로 관리를 추진하고 있다. 따라서, 실질적인 지표수-지하수 혼합대에서 발생하는 다양한 현상의 이해나 관리방안에 관한 연구는 아직 미비한 상황이다. 지표수-지하수 혼합대에 관한 보고서, 논문 등을 종합하여 혼합대의 영향인자를 살펴보면 1) 수리수문 특성에는 수리전도도·하천 수위·하천 유속·하천수 수온, 2) 수질 특성에는 유기오염물질·영양염류, 3) 수생태 특성에는 대형무척추동물 등으로 분류할 수 있다. 지금까지 단일 연구분야의 접근방법으로 다양한 현장측정기법 및 모델링을 통한 혼합대 연구가 수행되고 있지만, 혼합대가 가지는 환경적 중요성에 대한 이해와 인식이 부족하고, 혼합대 내부에서 발생하는 복합적인 프로세스로 인해 전문가들조차 연구에 어려움을 가질 것이다. 지표수-지하수 혼합대의 효율적인 관리를 위해서는 수리수문·수질·수생태 등 다양한 시각에서 접근하여 학제간 융합연구를 통해 기초 데이터를 상호교환하고, 기존의 혼합대 조사에 부족한 부분을 해결할 필요가 있다. 향후 하천 기저유출 및 혼합대 기초자료 구축, 혼합대 흐름 정량화, 하천복원사업에 의한 혼합대 영향 규명 등의 연구를 수행함으로써 혼합대를 체계적으로 관리할 수 있는 기술 방안을 제시할 필요가 있다.