• Journal of Korean Society of Water and Wastewater
• /
• v.27 no.6
• /
• pp.689-701
• /
• 2013

Bacterial growth and corresponding consumption of carbon and phosphorus were examined in which tap water samples containing a very low concentration of free chlorine were supplemented with organic carbon and/or phosphorus. The experiments were performed in a fed-batch mode under a controlled temperature of $20^{\circ}C$. In the phosphorus alone-added water, there was no significant increase in bacterial numbers measured as heterotrophic plate count (HPC) in the bulk water. However, bacterial growth was stimulated by the addition of carbon (e.g., bulk HPC levels increased to $10^3CFU/mL$) and further stimulated by the combined addition of carbon and phosphorus (e.g., bulk HPC to $10^5CFU/mL$). The same effects were observed in biofilm HPC and biomass formed on polyethylene (PE) slide surfaces. In the water where organic carbon and phosphorus were added together, the highest biofilm HPC and biomass (measured as extracellular polymeric substance components) densities were observed which were $7.6{\times}10^5CFU/cm^2$ and $5.3{\mu}g/cm^2$, respectively. In addition to the bacterial growth, additions of organic carbon and/or phosphorus resulted in different bacterial carbon-to-phosphorus (C/P) consumption ratios. Compared to a typical bacterial C/P consumption ratio of 100:1, a higher C/P ratio (590:1) occurred in the carbon alone-added water, while a lower ratio (40:1) in phosphorus alone-added water. Comparative value (80:1) of C/P ratio was also observed in the water where organic carbon and phosphorus were added together. At the given experimental conditions, bacterial growth was deemed to be more sensitive to microbially available organic carbon than phosphorus. The effect of phosphorus addition, which resulted in a lower C/P consumption ratio, seemed to be tightly associated with the presence of microbially available organic carbon. These results suggested that the control of extrinsic carbon influx seemed to be more important to minimize bacterial regrowth in drinking water system, since even low content of phosphorus naturally occurring in drinking water was enough to allow a bacterial growth.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.115-118
• /
• 2011

본 연구는 탄소발생 문제를 줄이는 방안을 개발하고자 LTE모형(친환경토지이용, 녹색교통, 녹색환경)을 3가지의 유형으로 나누어 각각의 유형에 해당되는 탄소저감방안을 개발하고 사례대상지에 적용하였다. 그리고 계획요소를 대상지에 맞게 도출 한 후 시뮬레이션을 하여 탄소저감의 효과를 분석 하였다. 도출된 기법을 연구 대상지에 적용한 결과 높은 저감효과를 보이는 요소를 도출할 수 있었고, 경미한 수준의 저감효과를 보이는 요소도 도출할 수 있었다. 탄소저감 비율은 25.51%이었고, 그중에서 특히 교통정온화 계획요소가 95.42% 압도적인 비율로 저감효과가 있음을 알 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.163.2-163.2
• /
• 2016

타이타늄과 탄소의 비율이 서로 다른 조건에서, 탄소가 도입된 산화타이타늄 (TiO2)을 수열합성법을 이용하여 합성하였다. TEM 이미지를 통하여 일정한 형태의 산화타이타늄이 합성된 것과, XRD 패턴 분석을 통하여 Anatase 형태임을 확인하였다. 본 연구에서는 탄소가 도입된 산화타이타늄을 이종상촉매로 사용하여 일차 및 이차 알코올 산화반응과 메틸렌 블루 분해 실험에 응용하였다.

• Composites Research
• /
• v.33 no.6
• /
• pp.336-340
• /
• 2020

In this study, carbon aerogels (CA) were prepared by sol-gel polycondensation of resorcinol and furfural in isopropanol using hexamethylenetetramine as a catalyst, and then directly drying the organic gels under isopropanol freeze-drying conditions, followed by carbonization under a nitrogen atmosphere. The preparation conditions of the CA were explored by changing the mole ratio of resorcinol to furfural. The effect of the preparation conditions on the pore structure of the CA was studied by nitrogen adsorption isotherms. The characteristics of the CA were studied by scanning and transition electron microscopy, and infrared spectrometry. The accessibility of pores and performance of the CA as an electrode in electric double layer capacitors were also electrochemically investigated. As a result, BET surface area and specific capacitance increased with the molar ratio of resorcinol to catalyst (R/C) ratio; the maximum values of 765 ㎡/g and 132 F/g were achieved at the R/C ratio of 200, respectively. Consequently, it was confirmed that increasing the R/C ratio increased the average pore size of the CA electrode, which improved the rate capability of the system.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.4
• /
• pp.67-83
• /
• 2022

Biochar is a carbon material produced through the pyrolysis of agricultural biomass with limited oxygen condition. It has been suggested to enhance the carbon sequestration and mineralization of soil carbon. Objective of this study was to investigate soil potential carbon mineralization and carbon dioxide(CO₂) emissions in different soils cooperated with barely straw and livestock manure biochars in the closed chamber. The incubation was conducted during 49 days using a closed chamber. The treatments consisted of 2 different biochars that were originated from barley straw and livestock manure, and application amounts were 0, 5, 10 and 20 ton ha^-1 with different soils as upland, protected cultivation, converted and reclaimed. The results indicated that the TC increased significantly in all soils after biochar application. Mineralization of soil carbon was well fitted for Kinetic first-order exponential rate model equation (P<0.001). Potential mineralization rate ranged from 8.7 to 15.5% and 8.2 to 16.5% in the barely straw biochar and livestock manure biochar treatments, respectively. The highest CO₂ emission was 81.94 mg kg^-1 in the upland soil, and it was more emitted CO₂ for barely straw biochar application than its livestock biochar regardless of their application rates. Soil amendment of biochar is suitable for barely straw biochar regardless of application rates for mitigation of CO₂ emission in the cropland.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.768-773
• /
• 2014

In this study, experimental and numerical studies for the synthesis of carbon nanotube(CNT) in methane counterflow diffusion flame have been performed. Methane mixed with acetylene($C_2H_2$) was used as a fuel gas and ferrocene was used as a catalyst for synthesis of CNT. The major parameters was $C_2H_2$ mixing rate and mixing rates were 2 %, 6 %, and 10 %. Characteristics of CNT formation on grid were analyzed from SEM images. the chemical reaction mechanism adopted is GRI-MECH 3.0. Numerical results showed that flame temperature and CO mole fraction were increased with increasing acetylene mixing rate. Experimental results showed that the CNT synthesis in 2% acetylene mixture flame better than that of 6% and 10% acetylene mixture flames. It can be considered that 6% and 10% acetylene mixture flames generated the excessive carbon source and then it interrupted the supplement of the carbon source into ferrocene catalyst. It can be found that the supply of appropriate quantity of carbon source can make effect to synthesis of high purity of CNT.

• Resources Recycling
• /
• v.27 no.2
• /
• pp.55-62
• /
• 2018

This study aims to investigate the characteristics on bottom ash flotation using vegetable oils as a collector. The experiment of changing the kerosene dosage as a collector for the flotation of coal ashes, the recovery of unburned carbon and unburned carbon content were 80% and 63%, respectively, when the dosage of kerosene was 9 kg/ton. The experiment of using soybean oil as a collector to improve flotation efficiency, the recovery of unburned carbon and unburned carbon content increased to 95% and 68%, respectively, when the dosage of soybean oil was 9 kg/ton. The recovery of unburned carbon and unburned carbon content were 99% and 78%, respectively, when safflower oil containing more poly unsaturated fats with double bonds than soybean oil was 9 kg/ton. The calorific value of the unburned carbon was 5,803 cal/g, confirming that it was possible to be used as a fuel for thermal power plants. Lastly, using vegetable oil as a collector it showed higher recovery of unburned carbon and higher unburned carbon than kerosene, which was mineral oil. Moreover, oil containing a large amount of poly unsaturated fat with two or more double bonds was found to have higher unburned carbon than other vegetable oils; thus showing excellent adsorbability for unburned carbon.

• Journal of Sericultural and Entomological Science
• /
• v.10
• /
• pp.1-25
• /
• 1969

Since widely use of anthracite for the radiating purpose in a rearing room in Korea, the weakness of silkworm, poor uniformity of the worm growth, the increase of missing worm ratio, unusual cocoon assorting ratio, and the decrease of cocoon layer ratio have been realized by the author, therefore, he has started out to search the mechanism of these evil influences regarding with various gas densities and terms of the gas treatment which will be supposed to be a warning for temperature control during the silkworm reading work. Among the anthracite gas components, CO or SO$_2$ influence and their complexed harm effect were investigated through the use of anthracite gas, CO and SO$_2$ gas. Meantime, each treatment was applied, separately, during the worm egg stage, young instar, adult instar and whole instar, because the harm intensity for any improperable rearing condition is flexible by the growing stages. Meantime, the gas density and term variation were applied for the above each treatment such as in case of anthracite and CO gas, the following treat methods were used. 1) 0.06% for 30 mins. 2) 0.06% for 1 hour. 3) 0.1% for 1 hour. 4) 0.15% for 1 hour. on the other hand, SO$_2$ gas was used as 1) 120ppm for 30 mins. 2) 200ppm for 30 mins. 3) 400ppm for 30 mins. The measurement of gas density was proceeded by using CO tester (Carbon Monoxide Indicator) and SO$_2$ tester (Indicator Sampler Cgf) which could keep any specific density before each treatment.

• Composites Research
• /
• v.19 no.2
• /
• pp.7-12
• /
• 2006

Graphite particle/carbon fiber hybrid conductive polymer composites were fabricated by the compression molding technique. Graphite particles were mixed with an epoxy resin to impart the electrical conductivity in the composite materials. In this study, graphite reinforced conductive polymer composites with high filler loadings were manufactured to accomplish high electrical conductivity above 100S/cm. Graphite particles were the main filler to increase the electrical conductivity of composites by direct contact between graphite particles. While high filler loadings are needed to attain good electrical conductivity, the composites becomes brittle. So carbon fiber was added to compensate weakened mechanical property. With increasing the carbon fiber loading ratio, the electrical conductivity gradually decreased because non-conducting regions were generated in the carbon fiber cluster among carbon fibers, while the flexural strength increased. In the case of carbon fiber 20wt.% of the total system, the electrical conductivity decreased 27%, whereas the flexural strength increased 12%.

• Composites Research
• /
• v.20 no.6
• /
• pp.1-7
• /
• 2007

Expanded graphite/carbon fiber hybrid conductive polymer composites were fabricated by the preform molding technique. The conductive fillers were mechanically mixed with a phenol resin to provide an electrical property to composites. The conductive filler loading was fixed at 60wt.% to accomplish a high electrical conductivity. Expanded graphites were excellent in forming a conductive networking by direct contacts between them while it was hard to get the high flexural strength over 40MPa with using only expanded graphite and phenol resin. In this study, carbon fibers were added in composites to compensate the weakened flexural strength. The effect of carbon fibers on the mechanical and electrical properties was examined according to the weight ratio of carbon fiber. As the carbon fiber ratio increased, the flexural strength increased until the carbon fiber ratio of 24wt.%, and then decreased afterward. The electrical conductivity gradually decreased as the increase of the carbon fiber ratio. This was attributed to the non-conducting regions generated among the carbon fibers and the reduction of the direct contact areas between expanded graphites.