• Korean Journal of Mineralogy and Petrology
• /
• v.34 no.3
• /
• pp.169-176
• /
• 2021

This study aimed to fundamentally understand structural changes of zeolite under pressure and in the presence of different pressure-transmitting media (PTM) for application studies such as immobilization of heavy metal cation or CO₂ storage using pressure. High-pressure X-ray powder diffraction study was conducted on the zeolite-W (K_6.4Al_6.5Si_25.8O₆₄× 15.3H₂O, K-MER) to understand linear compressibility and the bulk moduli in different PTM conditions. Zeolite-w is a synthetic material having the same framework as natural zeolite merlinoite ((K, Ca_0.5, Ba_0.5, Na)₁₀ Al₁₀Si₂₂O₆₄× 22H₂O). The space group of the sample was identified as I4/mmm belonging to the tetragonal crystal system. Water, carbon dioxide, and silicone-oil were used as pressure-transmitting media. The mixture of sample and each PTM was mounted in a diamond anvil cell (DAC) and then pressurized up to 3 GPa with an increment of ca. 0.5 GPa. Pressure-induced changes of powder diffraction patterns were measured using a synchrotron X-ray light source. Lattice constants, and bulk moduli were calculated using the Le-Bail method and the Birch-Murnaghan equation. In all PTM conditions, linear compressibility of c-axis (𝛽^c) was 0.006(1) GPa^-1 or 0.007(1) GPa^-1. On the other hand, the linear compressibility of a(b)-axis (𝛽^a) was 0.013(1) GPa^-1 in silicone-oil run, which is twice more compressible than the a(b)-axis in water and carbon dioxide runs, 𝛽^a = 0.006(1) GPa^-1. The bulk moduli were measured as 50(3) GPa, 52(3) GPa, and 29(2) GPa in water, carbon dioxide, and silicone-oil run, respectively. The orthorhombicities of ac-plane in the water, and carbon dioxide runs were comparatively constant, near 0.350~0.353, whereas the value decreased abruptly in the silicone-oil run following formula, y = -0.005(1)x + 0.351(1) by non-penetrating pressure fluid condition.

• Applied Chemistry for Engineering
• /
• v.26 no.3
• /
• pp.336-340
• /
• 2015

Three different types of polycarbonate (PC)/graphene oxide (GO) composites using diphenyl carbonate as a monomer were fabricated by melt polymerization. Those were the PC/GO composite (PC/GO) using a twin extruder, in-situ PC/GO composite (PC/GO-cat.) using a catalyst, and in-situ PC/GO composite (PC/GO-COCl) using a GO-COCl treated by -COCl, Chemical structures of the composites were confirmed by C-H and C=O stretching peak at $3000cm^{-1}$ and $1750cm^{-1}$, respectively. The slope for the storage (G') versus loss (G") modulus plot decreased with an increase in the heterogeneous property of polymer melts. So we can check the GO dispersion of the PC/GO composites using by the slop for G'-G" plot. According to the G'- G" slopes for three different types of PC/GO composites, GO was well dispersed within PC matrix in case of PC/GO and PC/GO-cat.. It was also confirmed by atomic force microscope (AFM) photos. One of the reasons for the poor GO dispersion of PC/GO-COCl is branching and crosslinking processes occurred during polymerization, which was further confirmed by a plot for the complex modulus versus phase difference.

• Journal of Adhesion and Interface
• /
• v.16 no.3
• /
• pp.101-107
• /
• 2015

Epoxy resin toughening agents such as core/shell nanoparticles, CTBN epoxy, polyester polyols, and polyurethane have been widely used in order to compensate for the brittleness and improve the impact resistance of the epoxy resin. In this work, a few tougheners mentioned above were individually added into adhesive compositions to observe the effects of physical and mechanical properties. Both flexural strength and flexural modulus were measured with UTM while impact strength was analyzed with Izod impact tester. The obtained results showed that the addition of toughening agents afforded positive performance in terms of flexibility and impact resistance of the cured epoxy resin. Furthermore, DMA experiments suggested that the trends of storage modulus data of each epoxy resin composition coincided with the trends of flexural modulus data. FE-SEM images showed that toughening agents formed circled-shape particles when it was cured in epoxy resin composition at high temperature by phase separation. The existence of particles in the cured samples explains why epoxy resin with toughener has higher impact resistance.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.190-197
• /
• 2005

Nanocomposites of three different polyesters with dodecyltriphenylphosphonium-montmorillonite $(C_{12}PPh-MMT)$ as an organoclay are compared with their thermal properties, mechanical properties, and morphologies. Poly (butylene terephthalate) (PBT), poly(ethylene terephthalate) (PET), and poly(trimethylene terephthalate) (PTT) were used as matrix polymers in the fabrication of polyester nanocomposite fibers. The variations of their properties with organoclay content in the polymer matrix and draw ratio (DR) are discussed. Transmission electron microscopy (TEM) micrographs show that some of the clay layers are dispersed homogeneously within the polymer matrix on the nano-scale, although some clay particles are agglomerated. We also found that the addition of only a small amount of organoclay is enough to improve the thermal stabilities and mechanical properties of the polyester nanocomposite fibers. Even polymers with low organoclay contents $(<5\;wt\%)$ were found to exhibit much higher strength and modulus values than pure polyester fibers. In the cases of all polyester hybrid fibers, the values of the tensile mechanical properties were found to decrease linearly with increasing DR. However, the initial tensile modulus of the PTT hybrid fibers were found to be independent of DR.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.1
• /
• pp.11-18
• /
• 2020

High-pressure synchrotron X-ray powder diffraction experiments were performed on natural illite (K_0.65Al₂(Al_0.65Si_3.35)O₁₀(OH)₂) using diamond anvil cell (DAC) under two different pressure transmitting media (PTM), i.e., water and ME41 (methanol:ethanol = 4:1 by volume). When using water as PTM, occasional heating was applied up to about 250℃ while reaching pressure up to 2.7 GPa in order to promote both hydrostatic conditions and intercalation of water molecules into the layer. When using ME41, pressure was reached up to 6.9 GPa at room temperature. Under these conditions, illite did not show any expansion of interlayer distance or phase transitions. Pressure-volume data were used to derive bulk moduli (K₀) of 45(3) GPa under water and 51(3) GPa under ME41 PTM. indicating no difference in compressibility within the analytical error. Linear compressibilities were then calculated to be β^a = 0.0025, β^b = 0.0029, β^c = 0.0144 under ME41 PTM showing the c-axis is ca. six times more compressible than a- and b-axes. These elastic behaviors of illite were compared to muscovite, one of its structural analogues.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.518-525
• /
• 2013

To improve the mechanical properties of polypropylene (PP) biocomposites reinforced with sulfuric acidtreated green algae (SGA), SGA/graphite nanoplatelets (GNP)/PP biocomposites were prepared and their properties were evaluated depending on the particle size and content of GNP. The flexural and impact strength of SGA/GNP/PP biocomposites decreased with the addition of GNP, whereas the flexrual and storage moduli were greatly improved with increasing GNP loading. SGA/GNP/PP biocomposites reinforced with GNP5 showed generally better mechanical properties compared to that reinforced with GNP15 mainly due to the improved dispersion of the smaller GNP. SGA/GNP/PP biocomposites reinforced with GNP5 showed a lower resistance to the thermal expansion because the relatively uniform dispersion of smaller GNP was responsible for the effective heat transfer to the polymer matrix. As a result, SGA/GNP/PP biocomposite was acceptable for the general purpose application due to the improved flexural resistance, storage moduli, and damping characteristics.

• Composites Research
• /
• v.35 no.3
• /
• pp.127-133
• /
• 2022

Polypropylene (PP) has been received great attention as a next-generation high-voltage power cable insulation material that can replace cross-linked polyethylene (XLPE). However, the PP cannot be used alone as an insulation material because of its high elastic modulus and vulnerability to impact, and thus is mainly utilized as a form of a copolymer with rubber phases included in the polymerization step. In this paper, a soft PP-based blend was prepared through melt-mixing of impact PP, polyolefin elastomer, and propylene-ethylene random copolymer. The elastic modulus and impact strength of the blend could properly be decreased or increased, respectively, by introducing elastomeric phases. Furthermore, the blends showed a high storage modulus even at a temperature of 100℃ or higher at which the XLPE loses its mechanical properties. In addition, the blend was found to be effective in suppressing the space charge compared to the pristine PP as well as XLPE.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.376-377
• /
• 2003

전기방사(electrospinning)는 최근 나노기술의 대두와 함께 서브마이크론(submicron)의 직경을 가지는 섬유를 제조할 수 있는 방법으로 활발한 연구가 진행되고 있는 실정이다[1]. 이러한 전기방사는 고분자 용액이나 용융된 고분자에 고전압을 걸어주어, 모세관 팁과 웹을 받아주는 컬렉터(collector) 사이에 전기장을 형성시켜 섬유를 제조하는 방법이다. 열가소성 폴리우레탄은 우수한 탄성을 갖는 유용한 고분자중의 하나로 섬유나 플라스틱에 널리 사용되고 있다. 특히, 이는 고무에 비하여 탄성률이 높고 내마모성이 강하며 용매에 대한 저항성이 좋은 장점을 지니고 있다[2]. (중략)

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.474-477
• /
• 2002

열가소성 폴리우레탄(PU)은 우수한 탄성을 갖는 유용한 고분자중의 하나로 섬유나 플라스틱에 널리 사용되고 있다. PU는 상온보다 높은 유리전이 온도(T$_{g}$)를 갖는 유리상의 hard segment와 상온보다 낮은 유리전이 온도(T$_{g}$)를 갖는 고무상의 soft segment로 구성되어 있으며 열역학적으론 비상용성으로 인하여 미세 상분리 구조를 가지게 되어 고무보다 높은 탄성률과 우수한 인장 회복거동을 갖게 된다[1-3]. (중략)

• The Korean Journal of Rheology
• /
• v.7 no.1
• /
• pp.60-67
• /
• 1995

EPDM/BR 블렌드의 물성에 미치는 커플링결합체의 영향을 조사하였다. N,N＇ -(bis(2-methyl-2-nitroprpyl))-1,6-diamino hexane) (MNPDH)와 bis(3-triethoxysilyl propyl)-tetrasulfide (TESPT)의 두가지 종류의 커플링결합제를 사용하였다. EPDM/BR 블 렌드 및 EPDM/BR/MNPDH 또는 EPDM/BR/TESPT 블렌드의 용융점도, 탄성률 및 tan $\delta$ 를 모세관 점도계, 동적점탄성장치 및 동적응력 완화측정장치로 조사하였다. 동적점탄성 및 형태학적 연구 결과 MNPDH 또는 TESPT를 첨가할 경우 결합고무 함량이 증가하고 카본 블랙의 분산성이 좋아져 가황된 EPDM/BR 블렌드의 인열강도 및 내피로성등의 물성이 향 상되었다.