• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.358-366
• /
• 2019

The purpose of this study is to explore the possibility of estimating optimum surface finishing work time of the fresh concrete placed at the job site by applying a surface hardness test meter(Durometer). Tests are carried out by measuring and comparing the Proctor penetration resistance test and hardness test by Durometer. Correlations between Procter penetration test and hardness test by Durometer were obtained. Two different types Durometer were applied to estimate setting time. Test results indicate that the measurement of the Durometer and the test of the Proctor penetration resistance are highly correlated. When measuring the initial setting time with Durometer, initial setting time is reached when the hardness value by the type C Durometer is reached around 42HD, and when final setting is measured with the type D Durometer, the surface finishing work time limit and curing time can be estimated with 10HD of Durometer.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.9
• /
• pp.143-150
• /
• 2019

The purpose of this study was to propose how to determine the setting time related to the determination of the surface finish working time of the concrete using a Durometer, which is used as a rubber hardness meter. Two different types of Durometer were used to measure the setting time of the concrete. High flowing concrete with 40% of water to binder ratio was fabricated maintaining $600{\pm}100mm$ of slump flow. The test results indicated that the application of the Durometer resulted in a high correlation with the penetration resistance tester in both mortar and concrete. When measuring the setting time of the concrete, with properly used with Durometer, evaluation of the setting time of the concrete can be available. Therefore, it is thought that the measurement of the final set of the durometer C type can be useful to decide the limit time of the finishing operation and the time of the rejuvenation of the curing process by measuring the finishing set at 40 HD in the case of the initial set and 10 HD in the case of D type.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.1
• /
• pp.33-38
• /
• 2020

The aim of the research is to evaluate the feasibility of durometer for assessing setting time of the concrete by comparing it with the currently used proctor penetration test method to improve the surface finishing timing determining method generally determined based on the experience of the worker. As a research result, the correlation between suggesting method using durometer with currently used proctor penetration test method was high enough. Hence, on the surface of the concrete, the initial setting time and the final setting time could be designated as 41 HD with C-type, and 11 HD with D-type, respectively. Therefore, the durometer can be used as a portable setting time evaluation device with the easiness of handling and measuring for determining concrete surface finishing timing quantitatively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.449-452
• /
• 2008

This study is to manufacture HSCC (High flowing Self-Compacting Concrete) be able to construction without vibration & hardening, and it is stable according to the change of the surface number of aggregate and to examine the factor of reduction occurred before after hardening through the indoor experiment. It is essential to use of the thickener to increase the viscosity in the combined HSCC. In this result, it make more bubbles than HSCC of pulverulent body. The result of study has shown, through the surface air bubble by not passed air bubbles within concrete after hardening, It has bad effect in not only appearance of structures but strength & duration. It is the experiment for air bubble of concrete according to the types of aggregate (fine aggregate), mixing time of concrete, exfoliation, material of model form and so that reduce the air bubble of combined HSCC. Experiments have shown, the effect of exfoliation was bigger than the effect of form for the performance of surface finishing of combined HSCC after hardening according to the exfoliation or material of model form and the opaque guris has good condition of finishing.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.5
• /
• pp.433-440
• /
• 2020

In this study, a new type of Durometer was invented by modifying the currently used Durometer with the hemisphere shaped needle to columnar shaped needle. The aim of the study is, hence, to provide the feasibility of the advanced Durometer for assessing setting time of the concrete. Generally, the finishing of concrete surface should be conducted to secure the smooth surface, improve the permeability, and prevent the plastic shrinkage cracking. Although this surface finishing work should be conducted during the plastic phase between initial and final setting, currently in practical situations, the timing of starting the finishing work was determined by the sense of the worker. To improve this situation, Kato Junji suggested to use the hemisphere and needle shaped Durometers to determine the initial and final setting time, respectively. However, in this case, there are difficulties of using two different Durometers and of occurring failure of the Durometer due to the intruded cement paste. To prove the feasibility of new typed Durometer, setting time and surface hardness were evaluated by applying for the concrete with various replacing ratios of fly-ash and coal gasification slag as an aggregate.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.989-992
• /
• 2008

In this paper, we are presenting a case that integrates ultra high strength concrete(150MPa) with surface-exposed concrete. Ahead of the field application, we carried out laboratory experiment and B/P Test for a basic property of concrete(slump flow, air content, 50cm flow time, elapse time change and compression strength) and productivity. The next, we conducted Mock-up Test using simulation specimen to evaluate infilling, surface-finishing and hydration heat of concrete. We had satisfactory results for a basic property and hydration heat of concrete. However at the time of field application, it was occurred rupture of formwork because of high lateral pressure of concrete, and then formwork was reinforced and case-in-place time was adjusted. And regardless of low and high frequency vibration, it occurred to surface-pockmark. In case that applies ultra high strength concrete to surface-exposed concrete, we estimate that it is important of systematic management and improvement of construction.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.87-88
• /
• 2020

The purpose of this study is to explore the possibility of estimating optimum surface finish time of the fresh concrete placed at the job site by applying a surface hardness test meter(Durometer). Tests are carried out by measuring and comparing the Penetration resistance test and hardness test by Durometer. Penetration resistance tester and improved Durometer are similar, but the higher the temperature, the higher the setting time, and the higher the correlation was shown. When the hardness value of the improved Durometer is about 50 HD, it is found that the initial and 80 HD represent the end. It is expected that this will be useful in determining the finish time of the surface at the actual site.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.169-170
• /
• 2020

The purpose of this study is to explore the possibility of estimating optimum surface finish time of the fresh concrete placed at the job site by applying a surface hardness test meter(Durometer). Tests are carried out by measuring and comparing the Penetration resistance test and hardness test by Durometer. Penetration resistance tester and improved Durometer are similar, but the higher the temperature, the higher the setting time, and the higher the correlation was shown. When the hardness value of the improved Durometer is about 50 HD, it is found that the initial and 80 HD represent the end. It is expected that this will be useful in determining the finish time of the surface at the actual site.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.2
• /
• pp.169-175
• /
• 2015

Recently, a stone is preferred as a cladding materials because of its outstanding durability and luxurious character. However, because of running out of natural resources and restriction of production, it is expected that difficulty of stable supply, and thus alternative cladding materials for concrete wall is needed. Therefore, in this research, as an alternative cladding materials, exposed-aggregate concrete is studied using saccharin based retarder. For evaluating factors, changing water-to-cement ratio, dosages of saccharin-based retarder, and timing of water jet washing were tested on the surface properties of exposed-aggregate concrete. As a result, the most favorable surface performance was obtained at 0.75 day after the placing in 25% of water-to-cement ratio, and at one day after the placing in 35 and 55% of water-to-cement ratio, 1.5 day after the placing in 65% of water-to-cement ratio with $24m{\ell}/m^2$ of retarder application.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1999.06a
• /
• pp.187-191
• /
• 1999

공사현장에서 사용하고있는 거푸집의 대체를 오랫동안 연구 끝에 가로(60cm) 세로(120cm)의 규격의 PE-FORM을 개발한바 있으나, 일반 건설 현장에서 어떠한 형태의 구조물 시공을 위한 형틀을 제작함에 있어 통상적으로 기존 합판거푸집을 사용하고 있으나, 현재 국내에서 사용되고 있는 합판은 전량 수입에 의존하고 있어 외화낭비가 심할 뿐 아니라 평균 2-3회 정도밖에 사용하지 못해 자원 낭비를 초래하고 있으며, 합판 거푸집을 사용한 경우, 목공이 구조물의 형태에 맞춰 FORM을 일일이 제작해야하므로 시간과 비용의 소모가 크고 또한 FRP-FORM, EURO-FORM, STEEL-FORM GANG-FORM SYSTEM-FORM 등 구조물의 성격 형태에 따라 각종 개량된 거푸집을 사용한다고 해도 그것은 단순한 구조물의 형상을 만들어 내기 위한 형틀로써만이 이용되고 있을 뿐, 그 이상의 목적으로는 활용 할 수 없기 때문에 구조물의 특성상 방수 방식의 기능이 요구될 경우, 거푸집 해체 후 벽체의 내부 또는 외부에 액체, 몰탈, 에폭시, 쉬트 방수등 별도의 후속 공정이 추가되 번거로움이 있는 반면, 그 효과는 기대에 크게 미치지 못하고 있는 점을 착안, 수년 전부터 연구에 착수, 콘크리트 구조체의 방수ㆍ방식 문제를 해결 할 수 있는 획기적인 공법의 PE-PANEL의 요철형 거푸집 및 방수ㆍ방식공법을 개발해내는데 성공함으로써 지금까지 난제로만 여겨졌던 목재 거푸집의 대체 자재개발과 아울러 거푸집 겸 콘크리트 표면의 마감 처리을 동시에 해결한 매우 혁신적인 신기술이라 할 수 있다. (중략)