• Journal of Korean Society of Steel Construction
• /
• v.24 no.3
• /
• pp.313-323
• /
• 2012

The purpose of this study is to evaluate $CO_2$ reduction and the flexural performance of steel wire-integrated void deck plate slabs that were inserted in omega-shaped steel plates to reduce concrete and welded H-section beams. The void deck plate slab can secure the structure, not only reducing the weight of the building but it is also eco-friendly. Therefore, this study evaluated the flexural performance of the composite beam by conducting a monotonic loading test with the use of actuators. It quantitatively evaluated the $CO_2$ emission based on earlier studies. The main test parameters are the concrete thickness of upper slabs, and the interrupted width of the omega-shaped steel plate. The result of the test showed that the welded H-section beam applied steel wire-integrated void deck plate slabs that were inserted into the omega-shaped steel plate declined in flexural performance on the composite beam after reducing concrete volume. Likewise, it is effective in reducing $CO_2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6788-6798
• /
• 2015

In recent high speed rail way, the operating speed of train is enhanced and the introduction of EMU train vehicles is increased. In addition, as expected the demand of the concrete slab track and the trend of design cross-section reduction, the clear behavior of evaluation of internal slab layer is demanded about the variation of design load and speed. The purpose of this study is to evaluate and identify the mechanical behavior pattern of concrete slab track and track-road bed with the variation of axle load and train speed. To this end, the behavior of TCL and HSB was evaluated in according to the variation of axle load and speed. And the analysis results and the data measured TCL strain sensor, which was embedded in TCL slab under installation on Honam high speed railway, was analyzed. The analysis result shows that the strain are increasing in according to the speed-up of train, and line regression was obtained from measured data. Analysis data of the state of bonding condition of slab layer and measured data was analyzed. It is conducted that the TCL layer stress of HEMU 430X, which of axle load, is lighter was similar to the stress of KTX-Honam, the standard deviation of measured stress is dramatically increased.

• Journal of the Korea Concrete Institute
• /
• v.15 no.3
• /
• pp.482-493
• /
• 2003

Flat plate structures subjected to lateral load have less deformability than conventional moment frames, due to the brittle failure of plate-column connection. In the present study, parametric study using nonlinear finite element analysis was performed to investigate the deformability of flat plates. The numerical results show that as number of continuous spans increases, the deformability of flat plates considerably decreases. Therefore, existing experiments using sub-assemblages with 1 or 2 spans may overestimate the deformability of flat plates, and current design provisions based on the experiments may not be accurate in estimating the deformability. A design method estimating the deformability was developed on the basis of numerical results, and verified by comparison with existing experiment. In the proposed method, the effects of primary design parameters such as direct shear force, punching shear capacity, aspect ratio of connection, number of spans, and initial stiffness of plate can be considered.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.203-215
• /
• 2009

This study was conducted to develop the design methodology of longitudinal post tensioning for the post-tensioned concrete pavement (PTCP). The longitudinal stress distribution in the PTCP slab was analyzed when post tensioning was applied. Then, the tensile stress distribution in the PTCP slab due to the environmental and vehicle loads needed for the design was investigated. In addition, prestress losses were calculated considering the losses due to the frictional resistance between the slab and underlying layer and due to various reasons related to tensioning. The tensile stresses used for the design were obtained by adding the stresses from the critical conditions under both the environmental and vehicle loads. The prestress losses were obtained by considering actual field conditions. The effective post tensioning amount was determined by considering the design loads including environmental and vehicle loads and various losses, and the effect of the allowable tensile stress on the post tensioning amount was investigated. The initial stage of the design of the longitudinal post tensioning is to obtain the stresses under the design loads and the required prestress determined by subtracting the allowable tensile stress from the design stress. Then, the optimal tendon spacing and the tensioning amount can be obtained by comparing with the effective tensioning amount including various stress losses.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.6
• /
• pp.363-370
• /
• 2021

In this paper, we presented an optimized crack and flexural strength analysis of a glass-fiber reinforced polymer (GFRP) rebar, used as reinforcements for in-site railway concrete slabs. The insulation performance of a GFRP rebar has the advantage of avoiding the loss of signal current in an audio frequency (AF) track circuit. A full-scale experiment, and three-dimensional finite element simulation results were compared to validate our approaches. Parametric numerical results revealed that the diameters and arrangements of the GFRP rebar had a significant effect on the flexural strength and crack control performances of the concrete track slabs. The results of this study could serve as a benchmark for future guidelines in designing more efficient, and economical concrete slabs using the GFRP rebar.

• International Journal of Highway Engineering
• /
• v.9 no.2 s.32
• /
• pp.141-151
• /
• 2007

The current standards and specifications for the road pavement construction have been developed based on materials and construction methods. The pavements constructed in accordance with those specifications do not guarantee high performance of pavements since they do not consider long-term performance of pavements. Therefore, as part of the study to develop performance-based construction standards for pavements, the payment adjustment methods based on the pavement performance are currently being developed. This paper presents preliminary studies performed to develop the payment adjustment methods when there is deficiency in the concrete slab thickness that is one oi the most important factors for the pavement design and construction. First, the payment adjustment methods in USA were investigated. Then, the AASHTO failure equation, the relationship between slab thickness and stress, and the relationship between stress level and pavement life were employed to propose the payment adjustment concepts based on the pavement performance for the deficient slab thickness. The variation in the slab thickness according to measurement locations was investigated by taking cores. In addition, the measurement methods of slab thickness and the variation of measured thicknesses depending on performers were analyzed, and finally the methodology to develop the thickness deficiency ranges for the use in the payment adjustment methods was proposed.

• Magazine of the Korea Concrete Institute
• /
• v.16 no.4 s.81
• /
• pp.10-17
• /
• 2004

• Magazine of the Korea Concrete Institute
• /
• v.16 no.5 s.82
• /
• pp.16-19
• /
• 2004

• Magazine of the Korea Concrete Institute
• /
• v.22 no.2
• /
• pp.60-64
• /
• 2010

• Magazine of the Korea Concrete Institute
• /
• v.23 no.3
• /
• pp.53-55
• /
• 2011