• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.3
• /
• pp.369-375
• /
• 2010

Since multi-view images can be utilized for 3D visualization and surveying as well, a system calibration is an essential procedure. The cameras in the system are mounted to the holder and their locations and attitudes are relatively fixed. Therefore, the locations and the attitudes of the perspective centers of the four oblique looking cameras can be calculated using the location and attitude of the nadir looking camera and the boresight values between the cameras. In this regard, this research is focusing on the analysis of the relative location and attitude between the nadir and oblique looking cameras based on the results of the exterior orientation parameters after the aerial triangulation of the real multiview images. We acquired high standard deviations of the relative locations between the nadir and oblique cameras. Standard deviations of the relative attitudes between the cameras were low when only the exterior orientations of the oblique looking cameras were allowed to be adjusted. Moreover, low standard deviations of the relative attitudes came when we considered not all the exterior orientations of the cameras but the attitudes of them only.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.1
• /
• pp.63-72
• /
• 2013

The structural stability of fill dam largely depends on the engineering behavior of rock materials used as main zone for dam construction and it is necessary to understand well the stress-strain characteristics of fill materials as well as shear strength property. In addition, the numerical analysis of fill dam requires a thorough study for calibrating material properties and parameters of a coarse-grained soil constitutive model. In this paper, large triaxial test results for Buhang-dam fill materials are analyzed and constitutive model parameters are calibrated based on the test results. It is shown that MD constitutive model is capable to predict the stress-strain behavior of dense and loose coarse-grained soils used for Buhang-dam construction based on the comparison study between the experimental test result and numerical simulation.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.6
• /
• pp.525-534
• /
• 2018

Camera calibration is the process of determining the parameters such as the focal length of a camera, the position of a principal point, and lens distortions. For this purpose, images of checkerboard have been mainly used. When targets were automatically recognized in checkerboard image, the existing studies had limitations in that the user should have a good understanding of the input parameters for recognizing the target or that all checkerboard should appear in the image. In this study, a methodology for automatic target recognition was proposed. In this method, even if only a part of the checkerboard image was captured using rectangles including eight blobs, four each at the central portion and the outer portion of the checkerboard, the index of the target can be automatically assigned. In addition, there is no need for input parameters. In this study, three conditions were used to automatically extract the center point of the checkerboard target: the distortion of black and white pattern, the frequency of edge change, and the ratio of black and white pixels. Also, the direction and numbering of the checkerboard targets were made with blobs. Through experiments on two types of checkerboards, it was possible to automatically recognize checkerboard targets within a minute for 36 images.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.1
• /
• pp.31-43
• /
• 2015

This study had been aimed to conduct the camera calibration on VLBI antenna in the Space Geodetic Observation Center of Sejong City with a low-cost digital camera, which embedded in a mobile phone to determine the three-dimension position coordinates of the VLBI antenna, based on stereo images. The initial values for the camera calibration have been obtained by utilizing the Direct Linear Transformation algorithm and the commercial digital photogrammetry system, PhotoModeler $Scanner^{(R)}$ ver. 6.0, respectively. The accuracy of camera calibration results was compared with that the camera calibration results, acquired by a bundle adjustment with nonlinear collinearity condition equation. Although two methods showed significant differences in the initial value, the final calibration demonstrated the consistent results whichever methods had been performed for obtaining the initial value. Furthermore, those three-dimensional coordinates of feature points of the VLBI antenna were respectively calculated using the camera calibration by the two methods to be compared with the reference coordinates obtained from a total station. In fact, both methods have resulted out a same standard deviation of $X=0.004{\pm}0.010m$, $Y=0.001{\pm}0.015m$, $Z=0.009{\pm}0.017m$, that of showing a high degree of accuracy in centimeters. From the result, we can conclude that a mobile phone camera opens up the way for a variety of image processing studies, such as 3D reconstruction from images captured.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.30 no.1
• /
• pp.31-38
• /
• 2012

The geo-referencing accuracy of the images acquired by a UAV based multi-sensor system is affected by the accuracy of the mounting parameters involving the relationship between a camera and a GPS/INS system as well as the performance of a GPS/INS system. Therefore, the estimation of the accurate mounting parameters of a multi-sensor system is important. Currently, we are developing a low altitude multi-sensor system based on a UAV, which can monitor target areas in real time for rapid responses for emergency situations such as natural disasters and accidents. In this study, we suggest a system calibration method for the estimation of the mounting parameters of a multi-sensor system like our system. We also generate simulation data with the sensor specifications of our system, and derive an effective flight configuration and the number of ground control points for accurate and efficient system calibration by applying the proposed method to the simulated data. The experimental results indicate that the proposed method can estimate accurate mounting parameters using over five ground control points and flight configuration composed of six strips. In the near future, we plan to estimate mounting parameters of our system using the proposed method and evaluate the geo-referencing accuracy of the acquired sensory data.

• Journal of the Korea Computer Graphics Society
• /
• v.21 no.1
• /
• pp.1-11
• /
• 2015

Researchers have developed virtual reality environments to provide audience with more visually immersive experiences than previously possible. One of the most popular solutions to build the immersive VR space is a multi-projection technique. However, utilization of multiple projectors requires large spaces, expensive cost, and accurate geometry calibration among projectors. This paper presents a novel omnidirectional projection system with a single projector and a single spherical mirror.We newly designed the simple and intuitive calibration system to define the shape of environment and the relative position of mirror/projector. For successful image projection, our optimized omnidirectional image generation step solves image distortion produced by the spherical mirror and a calibration problem produced by unknown parameters such as the shape of environment and the relative position between the mirror and the projector. Additionally, the focus correction is performed to improve the quality of the projection. The experiment results show that our method can generate the optimized image given a normal panoramic image for omnidirectional projection in a rectangular space.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.16-22
• /
• 2019

Off-line programming and robot calibration through simulation are essential when setting up a robot in a robot automation production line. In this study, we developed a new robot calibration method to match the CAD data of the production line with the measurement data on the site using 3D scanner. The proposed method calibrates the robot using 3D point cloud data through Iterative Closest Point algorithm. Registration is performed in three steps. First, vertices connected by three planes are extracted from CAD data as feature points for registration. Three planes are reconstructed from the scan point data located around the extracted feature points to generate corresponding feature points. Finally, the transformation matrix is calculated by minimizing the distance between the feature points extracted through the ICP algorithm. As a result of applying the software to the automobile welding robot installation, the proposed method can calibrate the required accuracy to within 1.5mm and effectively shorten the set-up time, which took 5 hours per robot unit, to within 40 minutes. By using the developed system, it is possible to shorten the OLP working time of the car body assembly line, shorten the precision teaching time of the robot, improve the quality of the produced product and minimize the defect rate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.485-486
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.111-112
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.489-490
• /
• 2008