• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.4
• /
• pp.1-7
• /
• 2015

A cavitation venturi is a device that allows a liquid flow rate to be fixed or locked independent of a downstream pressure and has been successfully used in a liquid rocket engine system which requires a stable propellant flow rate. In the present research, four cavitation venturis which have same dimensions except for converging inlet angle and diverging outlet angle, were designed and manufactured. Flow rates through each venturi and upstream/downstream pressures were measured by changing the pressures. From the experimental data, the discharge coefficients and critical pressure ratios were calculated for each venturi. It was found that the inlet and outlet angles of the cavitation venturi affected the discharge coefficient, and the outlet angle influenced on the critical pressure ratio.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.2-2
• /
• 2009

전통적으로 선박 프로펠러의 설계에 사용되는 수치해석방법을 소개하고, 점성유동장에서 작동하는 프로펠러의 해석을 포텐셜 이론을 적용해서 수행하는 방법을 소개한다. 캐비테이션 해석 등 최근의 프로펠러 주위 유동의 해석에 CFD가 적용되는 예를 보이고, 프로펠러의 성능 검증을 위해 실제 선박에서 수행되는 실험의 예를 보이고자 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.59-63
• /
• 2006

A direct photograph measurement technique was used to determine the spatial distribution of the spray droplet diameter in subsonic crossflow and it also obtain that SMD distribution by using PLLIF technique. The injector internal flow was classified as three modes such as a normal, cavitation, and hydraulic flip. The objectives of this research are getting a droplet distribution and drop size measurement of normal flow and compare with the other flow effects. Although the study showed visually that drop size were spatially dependent of Air-stream velocity, fuel injection velocity, and normalized distance from the injector exit length.(x/d, y/d) There are also difference characteristics between cavitation, hydraulic flip and the normal flow.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.227-233
• /
• 1999

This study is mainly concerned with phenomenon of cavitation-erosion on the several materials and corrosive liquids which were applied with vibrator (suggested by ASTM G-32, 20KHZ, 24{$mu}m$).The main results obtained are summarized as follows ; (1) The maximum erosion rate by cavitation erosion in both of fresh-water and sea-water appeared to be proportioned to their hardness and tensile strength. (2) Cavitation weight loss and rate of cast iron in sea-water condition were greater (approximately 3 times) than that in distilled-water condition, however in case of stainless and brass the cavitation weight loss and their rates were not so different in both of their conditions. (3) Cavitation weight loss of composite materials were shown as below on this test, DuraTough DL : Weight loss in sea-water condition were greater (approximately 2.3 times) than it's fresh-water condition. (4) As the result of observation with digital camea of specimens, the main tendency of cavitation erosion for metals, was that small damaged holes causing by cavitation e개sion was appeared with radial pattern, and composites materials was that small damaged holes were appeared randomly.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.14-19
• /
• 2011

Two difference cavitation models based on the homogeneous mixture model are used to study cavitating flows through converging-diverging channel. Here, the cloud cavities, pressure distributions and other results have been obtained and compared to evaluate two cavitation models. What's more, differences are observed in the simulated results, due to the differences in characteristics of each model. Analytical results shows that the new improvement cavitation model is validated to have better effects on simulating cavitating flows

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.3
• /
• pp.1074-1082
• /
• 1996

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.5
• /
• pp.220-226
• /
• 2007

The two major objectives of acoustical measurements in a cavitation tunnel are measuring the noise levels generated by rotating propellers behind a hull and localizing possible noise sources in order to reduce noise levels. Propeller noise measurement experiments were performed in MOERI cavitation tunnel at December, 2006. In order to put the propeller into cavitating conditions, a wake-generating dummy body was devised. In addition, ten hydrophones are put inside a wing-shaped casing in order to minimize the unexpected flow induced self noise around hydrophone itself. After measuring both of the noises of the rotating propeller behind the dummy body and signals generated by a virtual source, respectively the data were matched field processed using the frequency incoherent Bartlett processor to localize noises on the propeller plane. In this paper, we presented the measured noise analysis and the localization results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.93-99
• /
• 2005

Performed were 2-phase numerical studies on two types of fuel atomizers, plain orifice and pressure swirl atomizer. In case of plain orifice, cavitation model was applied so that discharge coefficient, cavitation size, and magnitude of cavitation region characterized and compared with experimental results for several different pressure enforced to the orifice. In case of swirl atomizer, VOF model was applied to analyze air core size, spray angle, and wall pressure distributions with comparison of experimental results.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.3
• /
• pp.49-53
• /
• 2010

The computational studies on the cavitating flow around a turbopump inducer were performed to see the effect of the cavitation on the performance of the inducer. The development of cavities around the inducer blades and the head drop of the inducer are observed as the inlet pressure reduces. The change of the backflow at the inducer inlet is also observed with the development of the cavities. The size of the backflow reduces as the inlet pressure is reduced due to the development of the cavities around the blades. The predicted suction performances of the inducer were compared with the experimental results. The results show that the computations overestimate the suction performances of the inducer than the experiments.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.1
• /
• pp.94-103
• /
• 1993

This study deals with an investigation on the tip vortex generated by an elliptic wing with section shapes of NACA 0020. The flow structure on the wing surface is investigated by using tufts test as well as observing the cavitation pattern. The surface pressure on a foil surface is measured to complement the visualized flow field. Results show that a strong spanwise pressure gradient is a definite contributor on the formation of tip vorex, and the fluids from both sides contribute to the evolutionary process of tip vortex. On the other hand, a series of experiments are conducted to investigate the detailed structure of tip-vortex at various angles of attack. The tip-vortex formation and development are observed by producing a cavitation, and then by a laser sheet technique in conduction with a dye injection method. The shape of tip-vortex and the distance between a vortex core and the trailing vortex sheet are found to vary with the angle of attack. Overall features of tip flow are evaluated to complement the vortex model based on inviscid theory.