• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.4
• /
• pp.157-162
• /
• 1987

The basic experiments on the plastic sea eel pots used in fishing were carried out in order to investigate the elasticity of the funnel ribs, hydrodynamic resistance, sinking time and diffusion of the bait from June to October, 1987. The elasticity of the bamboo funnel ribs was higher than that of the polypropylene ribs up to the load 150g. The hydrodynamic resistance R (kg) of the pots towing to the head direction horizontally in relation to towing velocity V (m/sec) was expressed as following formula; R=0.36V super(2.01) and coefficient of drag C sub(D) was 0.52. The sinking times of the covered pots by tape fully or partially were late 1-2 second than the typical pots within the water depth 7.5m. The diffusion tendency through the covered pots using dye and sardine extracts solution was concentrated to the entrance more than the typical pots. However, fishing efficiency as number and weight of fish per pots for nine times fishing operation was revealed no difference between the covered pots and the typical pots.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.11
• /
• pp.905-911
• /
• 2015

In this study, to examine the effect of a hole size change(smaller hole diameter) in the outer region of the lower-support-structure-bottom plate(LSSBP) on the reactor core-inlet flow-distribution, simulations were conducted with the commercial CFD software, ANSYS CFX R.15. The predicted results were compared with those of the original LSSBP. Through these comparisons, it was concluded that a more uniform distribution of the mass flow rate at the core-inlet plane could be obtained by reducing the hole size in the outer region of the LSSBP. Therefore, from the nuclear regulatory perspective, design change of the hole pattern in the outer region of the LSSBP may be desirable in terms of improving both the mechanical integrity of the fuel assembly and the core thermal margin.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.51.4-52
• /
• 2016

이 논문에서는 "원사" "천문지" <경부>조의 기록을 바탕으로 조선시대 영부에 대해 연구하였다. 조선에서는 1435년과 1440년에 처음으로 대규표와 소규표가 제작되었으며, 이들은 모두 횡량을 가진 진화된 형태의 규표로써 영부를 사용하여 그림자길이를 측정하였다. 영부는 바늘구멍 장치로 Needham et al.에 의해 처음으로 그 모델이 제시되었지만, 구조적 측면에서 "원사"의 원문 내용과 차이를 보이고 있다. 이 연구에서는 조선시대 영부를 "원사"의 경부와 동일했을 것으로 가정하였으며, 이를 토대로 새로운 모델을 제시하였다. 바늘구멍을 통과하는 빛의 경로에 대한 분석을 통해 새 모델의 재원 중 "원사"에 명시되지 않은 영부 밑받침의 높이를 추정하였다.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2021.06a
• /
• pp.85-88
• /
• 2021

포인트 클라우드 콘텐츠는 실제 환경 및 물체를 3 차원 위치정보를 갖는 점들과 그에 대응하는 색상 등을 획득하여 기록한 실감 콘텐츠이다. 위치와 색상 정보로만 이뤄진 3 차원 점으로 이뤄진 포인트 클라우드 콘텐츠는 확대하여 렌더링 할 경우 점과 점 사이의 간격이 벌어지면서 발생하는 구멍에 의해 콘텐츠 품질이 저하될 수 있다. 이러한 문제를 해결하기 위해 본 논문에서는 포인트 클라우드 확대 시 점들 간 간격이 벌어져 생기는 구멍에 대해 깊이정보를 활용한 역변환 기반 보간 방법을 통해 포인트 클라우드 콘텐츠 품질을 개선하는 방법을 제안한다. 벌어진 간격들 사이에서 빈 공간을 찾을 때 그 사이로 뒷면의 점들이 그려지게 되어 보간 방법을 적용하는데 방해요소로 작용한다. 이를 해결하기 위해 구멍이 발생하지 않은 시점에서 렌더링 된 영상을 사용하여 포인트 클라우드의 뒷면에 해당되는 점들을 제거한다. 다음으로 깊이 맵(depth map)을 추출한 후 추출된 깊이 값을 사용하여 뎁스 에지(depth edge)를 구하고 에지를 사용하여 깊이 불연속 부분에 대해 처리한다. 마지막으로 뎁스 값을 활용하여 이전에 찾은 구멍들의 역변환을 하여 원본의 데이터에서 픽셀을 추출한다. 제안하는 방법으로 콘텐츠를 렌더링 한 결과, 기존의 크기를 늘려 빈 영역을 채우는 방법에 비해 렌더링 품질이 평균 PSNR 측면에서 2.9 dB 향상된 결과를 보였다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.1
• /
• pp.74-82
• /
• 2002

The present study is aimed to investigate the effect of the safety hat on the balance of body temperature by observation of the physiological response under hot working environment. The experiment was carried out in a climate chamber of 3$0^{\circ}C$, 50%RH for 70 minutes. To compare the two kinds of safety hat, 5 healthy male subjects worn safety hat without hole (called 'without hole') or safety hat with hole (called 'with hole') according to a randomized cross-over design. The main results of this study are as fellows: Rectal temperature and heart rate were significantly lower level in 'with hole'than in 'without hole'. The mean skin temperature was significantly higher in 'without hole'than in 'with hole'. Blood pressure were significantly low in 'with hole'. Sweat rate which was measured by weight loss before and after experiment was higher in 'without hole'. In subjective ratings, subjects replied more hot, more uncomfortable and more wet, they felt more fatigue in condition of 'without hole'. Work ability which was measured by a grip strength dynamometer was higher in 'with hole'. Safety hat which can be used for safety of the brain in work place is meaningful device of behavioral thermoregulatory response under the hot working environment. The safety hat which is designed for proper ventilation and hygiene can maintain the homeostasis of body temperature by releasing body temperature efficiently.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.6 no.4
• /
• pp.327-334
• /
• 1994

The manifold designates a pipe system discharging or absorbing water through multiple holes installed along the finite length of the pipe. The proper design of the manifold requires the pre-analysis of the hydraulic characteristics such as system head and flow rate. head loss and hole discharges, etc. On the contrary to the general pipe systems. the head loss along the pipe is hardly quantified in an explicit way since it is complicately varied by the size and arrangement of the holes. In the present study, both energy and continuity equations are employed to analyze the hydraulic characteristics, constituting nonlinear simultaneous equations which are solved by Newton method. In addition, a hydraulic experiment utilizing the manifold system equipped with an automatically controlled valve is performed to reproduce model tide. The result shows that the manifold system can be effectively used in a tidal basin where water flow should be maintained uniformly over the basin width.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.76-80
• /
• 1993

절삭가공중에서 DRILL가공은 일반기계가공 공정중에 23 .approx. 25% 정도의 비율을 점우하고 있는 중요한 위치의 작업의 하나이고 또한 요구되는 정밀도를 만족하기 어렵고, 높은 생산성이 요구되는 가공법이다. 기계가공의 무인화, 자동화, 고능률화 및 정도향상 이라는 측면에서 더욱 이에 대응할 수 있는 가공방법 즉 공작물, 공구재료, 공구형상 및 절삭조건등에 걸쳐 광범위하게 연구개발 되어 져 가고 있다. 이 작업중 특히 곤란한 것은 깊은 구멍가공(DEEP HOLE DRILL)으로서 깊이/직경의 비가 극히 높은(약 5배이상) 절삭가공 의 경우에는 CHIP의 배출, 절삭날부의 윤활, 공구의 진동등의 문제로 인하여 일반적인 절삭가공 공법으로는 가공이 여려운 경우가 많다. 본 연구는 Solid BTA Drill(Mlti-tip Drill Head with Brazed Tips)에 의하여 가공에요구되는 절삭성 분석과 절삭조건의 변화에 따른 공작물의 가공정도 즉, 가공구멍의 직경의 변화, 표면거칠기. 진원도의 변화상태 및 공구의 마모된 현상에 대하여 실험조사하여 공구에 제한된 수명을 연장하고, 제품에 요구되는 품질수준을 확보하는가에 대하여 본 실험을 통하여 분석하도록 하였다.

• Journal of the Korean Society of Radiology
• /
• v.18 no.1
• /
• pp.27-36
• /
• 2024

In this study, When acquisition thyroid scintigraphy images, a parallel hole collimator was applied, and the difference from the pinhole collimator was quantitatively analyzed under each image acquisition condition. Visual size, resolution, sensitivity, signal to noise ratio (SNR), and contrast to noise ratio (CNR) were evaluated using thyroid phantom and point source. When comparing visual size, it was confirmed that an image similar to the size of the pinhole collimator could be obtained only when a magnification ratio of about 2.00 to 2.09 times when applying a parallel hole collimator. There was no tendency in FWHM(mm) measurement using a point source, and sensitivity was high in the parallel hole collimator. SNR and CNR were high when using a low magnification ratio, matrix size of 128×128, and a parallel hole collimator. In images of similar size to the naked eye, when the matrix size was the same, both SNR and CNR were high in the pinhole collimator. Therefore, when performing a thyroid scintigraphy test, if appropriate conditions are set according to the situation of each hospital and a parallel hole collimator is applied, it can be a good option in terms of equipment utilization and work efficiency.

• Journal of Broadcast Engineering
• /
• v.26 no.6
• /
• pp.714-724
• /
• 2021

The point cloud content is immersive content recorded by acquiring points and colors corresponding to the real environment and objects having three-dimensional location information. When a point cloud content consisting of three-dimensional points having position and color information is enlarged and rendered, the gap between the points widens and an empty hole occurs. In this paper, we propose a method for improving the quality of point cloud contents through inverse transformation-based interpolation using depth information for holes by finding holes that occur due to the gap between points when expanding the point cloud. The points on the back are rendered between the holes created by the gap between the points, acting as a hindrance to applying the interpolation method. To solve this, remove the points corresponding to the back side of the point cloud. Next, a depth map at the point in time when an empty hole is generated is extracted. Finally, inverse transform is performed to extract pixels from the original data. As a result of rendering content by the proposed method, the rendering quality improved by 1.2 dB in terms of average PSNR compared to the conventional method of increasing the size to fill the blank area.

• Korean Journal of Ichthyology
• /
• v.20 no.4
• /
• pp.318-323
• /
• 2008

A single specimen of the ophichthid Muraenichthys gymnopterus (254.6 mm TL) was collected from the middle Yellow Sea off Incheon, Korea. It represents the first record of the species, the genus, and the subfamily from Korea. This species is characterized by the following combination of characters: a constricted midlateral gill opening; dorsal fin origin before anus, closer to the anus than to the gill opening; blunt teeth, jaw teeth in bands, and multiserial dentition; third preopercular pore present; single infraorbital pore between anterior and posterior nostrils; brownish colour; depth and width of gill opening 43.2 times and 33.7~65.3 times in total length, respectively; eye diameter 15.0~31.0 times in head length and total vertebrae 154~161. New Korean names are proposed, "Gaet-mul-baem-a-gwa" for the subfamily Myrophinae, "Gaet-mul-baem-sok" for the genus Muraenichthys, and "Gaet-mul-baem" for M. gymnopterus.