• Economic and Environmental Geology
• /
• v.27 no.1
• /
• pp.93-100
• /
• 1994

This study examined the mechanisms of lead transport in the groundwater system and those of irregular detections in groundwater in Door County, Wisconsin. During the spring recharge period in 1991, water-level movement and water-quality change were monitored from two monitoring wells equipped with three piezometers each and from five house wells, respectively. Water-level responses to recharge events were fast with a relatively short lag time ranging from 3 to 10 days, indicating that recharge of groundwater occurs through the high hydraulic conductivity (K) zones in the Silurian dolomite aquifer system. Lead was detected only on particles filtered from groundwater, but not in dissolved state. Concentrations ranged from 0.2 to $7.1{\mu}g/mg$, converted into the total lead concentration in groundwater ranging from $0.3{\mu}g/l$ to $4.7{\mu}g/l$. A lag time between recharge events and peak particle movement at the sampled wells was estimated to range from 19 to 22 days. Due to the particulate nature of lead in groundwater, only the wells connected with the high K zones detect lead, causing the spatial variation. In a given well, lead concentration varies at different sampling times due to the variation in the initial amounts of lead-carrying particles introduced into the groundwater system during recharge events, the lag in particle transport and the dispersion of lead-carrying particles along the advective flowpaths.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.723-729
• /
• 2016

This study compared fin-tube and parallel-flow heat pipes for their sensible heat exchange rate, heat recovery amount, and air-side pressure drop. Tests were done with different refrigerant charging rates of 40-60% vol. and air flow rates of 300-1,400. The sensible heat exchange rate was highest for both types of heat pipes at a working fluid charge of 40% vol. and low flow rate. For the parallel-flow heat pipe, the 60% vol. charge is too high and results in a low sensible heat exchange rate. The reason is that the thicker liquid film of the tube wall deteriorates the heat transfer effect. Hence, the optimal charging rate is 40 to 50% vol. The evaporator heat pipe has a larger air-side pressure drop than the condenser section heat pipe. The reason is considered to be condensation water arising from the evaporator surface. Compared to the fin-tube heat pipe, the parallel-flow heat pipe showed better performance with a working fluid charging rate of 48%, volume of 41%, and an air-side pressure drop about 37%.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.169-177
• /
• 2017

Recently, as the size of transportation vessels has increased, there is a growing need for securing the front-water depths of existing port facilities. The method of deepening front-water depth is securing the depth of the port facility, and it is reinforced by grouting after excavating the rubble-mound to the required depth. The purpose of this study is to investigate the reinforcing performance and filling performance of thixotropic grout as a grouting material for reinforcing rubble-mound. Compressive strength tests were carried out for two types of thixotropic grout, and 5 specimens with a diameter of 400 mm and a height of 530 mm were manufactured and evaluated for filling performance. The required strength of reinforced rubble-mound required to ensure the safety of the structure is 6 MPa. All the thixotropic grouts used in this study were found to satisfy the required strength over 9 MPa at 7 days of age. As a result of visual observation of filling state of the filling performance test specimens, it was confirmed that the thixotropic grout was well filled up to the desired fillet height.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.2
• /
• pp.406-413
• /
• 2022

The subsea pipeline pre-commissioning stage consists of the following processes: Flooding, Venting, Hydrotesting, Dewatering, Drying, and N2 Purging. Among these processes, drying and nitrogen purging processes are stipulated to reduce and maintain the relative humidity below dew point to prevent the generation of hydrate and the risk of gas explosion in the pipeline during operation. The purpose of this study is to develop an analysis method for the air drying and nitrogen purging process during pre-commissioning of the subsea pipeline, and to evaluate the applicability of the analysis method through comparison with on-site measurement results. An analysis method using Computational Fluid Dynamics (CFD) was introduced and applied as a method for evaluating the relative humidity inside a subsea pipeline, and it was confirmed that analysis results were in good agreement with the on-site measurement results for the air drying and nitrogen purging process of the offshore pipeline. If the developed air drying and nitrogen purging analysis method are used as pre-engineering tools for pre-commissioning of subsea pipelines in the future, it is expected to have a significant impact on the improvement of work productivity.

• Journal of KSNVE
• /
• v.7 no.3
• /
• pp.411-418
• /
• 1997

A method to analyze the axisymmetric vibration and the internal pressure of the fluid filled, strength member embedded infinite cylindrical shell under the condition of axial static tension load applied is presented. As an example, the hose wall vibration and the internal pressure variation characteristics of a fluid filled infinite polyurethane hose are analyzed and dicussed, under the effects of the variation of the embedded strength members and the response positions.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2001.11a
• /
• pp.44-45
• /
• 2001

VOCs의 일종인 benzene을 흡수하기 위한 최적의 세정액으로 열매체유를 선정하여, 충진탑(Packed Tower), 흡수칼럼에 세정액만 채워 bubble 시킨 기포탑(Aeration Tower)와 충진물과 세정액을 채워 bubble 시킨 Combined Packed & Aeration Tower의 3가지 시스템을 비교한 결과 Combined Packed 쇼 Aeration Tower 시스템에서 benzene 흡수효율이 가장 좋았다.

• The Korean Journal of Rheology
• /
• v.4 no.1
• /
• pp.46-51
• /
• 1992

본 연구에서는 열가소성고무를 중심으로 한 스티렌 공중합체의 유변학적 특성을 Couette 보정치를 사용하여 해석하였다. 실험재료로는 SBS(Styrene-Butadiene-Styrene), SEBS(Styrene-Ethylene/Buthylene-Styrene), SIS(Styrene-Isoprene-Styrene)을 사용하였고 탄성체의 성격을 비교하기 위하여SBS(Styrene-Butadiene Rubber)와 IR(Isoprene Rubber)를 사용하였다, 실험결과 Couette 보정치는 온도가 증가할수록 감소하였다. 또한 열가소성 고부 (SBS, SEBS, SIS)의 보정치는 거의 비슷한 값을 나타내었으며 고무(IR, SBR)의 보정치는 열가소성고무에서보다 다소 높은 값을 나타내었다. 충진제를 첨가하였을 경우 충진제의 양 이 증가할수록 Couette 보정치는 감소하였다.

• Transactions of Materials Processing
• /
• v.6 no.6
• /
• pp.489-499
• /
• 1997

The injection molding process is analyzed to get the information on the mold design parameters and the optimum process conditions for automotive plastic front fender. The gate position, runner size and cooling channel are determined by the estimation of the flow balance, packing time, uniform cooling and shrinkage and warpage in the injection molding analyses. The procedure can be used in the mold design in the early stage when developing plastic parts.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.12
• /
• pp.18-22
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.305-305
• /
• 2004

쾌속조형 기술은 3차원 CAD 데이터를 일정한 두께 간격으로 슬라이싱한 각 층을 다양한 방법으로 만들고, 이러한 층을 한층씩 적층하여 원하는 3차원 형상을 신속하게 제작하는 기술이다. 쾌속 조형법은 초기에는 광(beam)에 의해 형상이 만들어진다고 하여 광조형법이라고 불렸다. 그 후 시작품(Prototype)을 신속(Rapid)하게 제작할 수 있다는 사실로부터 'Rapid Prototyping' 또는 '쾌속 조형법' 이라고 불려지게 되었다.(중략)