• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.56-56
• /
• 2011

본 연구에서는 파랑의 변형을 예측하는 방법 중 하나인 고유함수전개법을 이용하여 축대칭 형태의 지형 위를 통과하는 파랑의 소멸파 성분을 검토하였다. 기울기와 곡률이 변하는 지역에 고유함수 전개법을 적용하여 해석할 때 필요한 적절한 구간의 수와 소멸파 성분의 개수를 산정하였다. 고유함수전개법을 이용하여 파랑의 변화를 예측하는 연구는 Bremmer(1951)가 전자기파에 적용하면서 처음 제시한 후 Takano(1960)가 파랑 변형 연구에 적용하면서 본격적으로 진행되었다. 이밖에 Kirby and Dalymple(1983), Liu et al.(1992), Cho and Lee(2000), Bender and Dean(2003), 조용식과 이창훈(1998) 및 강규영 등(2007)에 의해 국내 외로 많은 연구가 진행되었다. 그러나 기존의 연구의 대부분이 연직 2차원 지형에 대하여 수행되어 왔다. 3차원 지형에 대한 고유함수전개법은 Bender and Dean(2005)에 의해 처음으로 시작되었다. 그러나 그들의 연구에서는 수렴해를 얻기 위한 구간 및 소멸파 개수에 관한 구체적인 검토가 이루어지지 않았다는 한계가 있다. 그러나 실제 해저 지역은 다양한 지형의 영향을 받게 된다. 따라서 본 연구에서는 축대칭 지형에 대하여 수렴해를 얻기 위해 구간을 나누어 해의 수렴성을 확인하여 적절한 구간의 수를 결정한 후 소멸파의 수를 변화시키면서 소멸파가 파랑의 변형에 미치는 영향을 검토하였다. 천해역 및 중간수심 영역을 구간의 수와 소멸파 성분의 수에 변화를 주면서 수렴성 검사를 한 결과, 천해 영역에서는 소멸파 성분의 영향이 적게 나타났으나 중간수심 영역에서는 적절한 개수의 소멸파를 고려해야 보다 정확한 예측을 할 수 있음을 알 수 있었다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.3
• /
• pp.321-332
• /
• 2005

In this paper, the time-domain finite element formulations for axisymmetric linear viscoelastic problems, especially for the viscoelastic hollow sphere and cylinder, under various boundary conditions are presented with the theoretical solutions of them obtained by using the elastic-viscoelastic correspondence principle. It is assumed that the viscoelastic material behaves like a standard linear solid in distortion and elastically in dilatation. Numerical examples are solved based on the spherically symmetric, axisymmetric and plane strain finite element models. Good agreements are obtained between numerical and theoretical solutions, which shows the validity and accuracy of the presented method.

• Proceedings of the Korean Society of Rheology Conference
• /
• 2000.11a
• /
• pp.52-55
• /
• 2000

• The Journal of the Korea Contents Association
• /
• v.13 no.2
• /
• pp.505-511
• /
• 2013

A new boundary treatment technique which can be applied to axi-symmetric topography with inclined bottom was developed. Although the finite element method is good for complex geometry, there is no proper boundary treatment when a boundary is not a vertical section because the water depth at the coastline becomes zero. In this study, we developed a new boundary treatment for inclined bottom using the analytical solution for long wave. To develope a model, the mild-slope equation was used and then, a computational domain is divided into an analytical region and a numerical region. By combining a numerical and an analytical solutions, a complete solution was obtained. The developed solution was validated by comparing with a previous analytical solution.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.3
• /
• pp.330-336
• /
• 1989

In analyzing the axisymmetric backward extrusion process a new method of analysis using upper-bound theorem is proposed in which the plastic zone and dead metal zone cam be predicted. Experiments are carried out with commercial aluminum. The metal flow on the meridional plane has been visualized experimentally by using the gridded specimens. It is shown that the theoretical results both in extrusion load and deformation pattern are in good agreement with the experimental results and they can be used for effective punch and die design to consider various process parameters in axisymmetric backward extrusion.

• Journal of the Korea Convergence Society
• /
• v.9 no.1
• /
• pp.283-289
• /
• 2018

In automotive disc brake systems, frictional heat is not uniformly dispersed for reasons such as heat flux and thermal deformation. The thermoelastic deformation due to the frictional heat affects the contact pressure distribution and the contact load may be concentrated on the contact portion on the the disc brake surface, resulting in thermoelastic instability. In this study, thermal analysis and thermal deformation analysis considering the contact between disk and pad occurred during braking through 3D axial symmetry model with reference to the experimental equation and Kao's analysis method of contact pressure of disk and pad. ANSYS is used to analyze the thermal and elastic instability problems occurring at the contact surface between the disk and the pad, considering both the thermal and mechanical loads. A 3D axisymmetric model with direct contact between the disk and the pad was constructed to more accurately observe the thermal behavior of the disk by observing the frictional surface temperature, thermal deformation and contact thermal stress of the disk.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.63-72
• /
• 1995

Closed-die forging of spur gears with hollow cylindrical billet has been analysed by using the upper-bound method. A kinematically admissible velocity field has been developed, wherein, an involute curve has been introduced to represent the forging die profile. In the analysis, the deformation region has been divided into nine zones. A constant frictional stress has been assumed on the contacting surfaces. Utilizing the formulated velocity field, numerical calculations have been carried out to investigate the effects of various parameters, such as module, number of teeth and friction factor, on the forging of spur gears. Hardness and accuracy of forged gears are measured. The following results have been obtained: (1) It is verified that an axisymmetric deformation zone exists between root circle and center of gear through forged gears. (2) The average relative forging pressure is predominantly dependent on the number of teeth and increases near the final filling stage as the addendum modification coefficient increases. (3) Close agreement was found between the predicted values of forging load and those obtained from experimental results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.7
• /
• pp.745-751
• /
• 2011

This study proposes finite element modeling of dislocation punching at cooling after consolidation in order to calculate the strength of particle-reinforced aluminum composites. The Taylor dislocation model combined with strain gradient plasticity around the reinforced particle is adopted to take into account the size-dependency of different volume fractions of the particle. The strain gradients were obtained from the equivalent plastic strain calculated during the cooling of the spherical unit cell, when the dislocation punching due to CTE (Coefficient of Thermal Expansion) mismatch is activated. The enhanced yield stress was observed by including the strain gradients, in an average sense, over the punched zone. The tensile strength of the SiCp/Al 356-T6 composite was predicted through the finite element analysis of an axisymmetric unit cell for various sizes and volume fractions of the particle. The predicted strengths were found to be in good agreement with the experimental data. Further, the particle-size dependency was clearly established.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.488-500
• /
• 1987

The improvement of surface roughness of machined cylindrical rods through the plastic polishing process was studied in this paper. The criterion and limits for the plastic polishing process due to the wave motion of the ridge were established with respect to process variables: ridge shape and size, semi-cone die angle as well as friction factor, by the application of the upper-bound approach. The surface roughness of the plastic polished products was measured, and compared with that of the original specimen. Also the depth of the surface deformation layer was tested, and compared those of the theoretical values. Qualitative agreement exists between the experimental plastic polishing loads and theoretical loads. The wave motion of the ridge was mostly occurred within the established limits. The surface roughness of specimens was sufficiently improved through the present process. Also the predicted depth of the surface deformation layer was in good agreement with experimental results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.13-13
• /
• 1999

본 논문에서는 해석영역의 형상변화, 즉 로켓노즐 내열재의 삭마로 인해 야기된 경계 면의 이동을 고려하면서 2차원 비정상 비등방성 재료의 열전달 문제를 해석할 수 있는 수치해석에 대해 기술하였다. 수치해석 알고리즘은 유한요소법이며 열해석시 경계면 이동으로 인한 격자계의 절점 좌표점이 계산과정 동안에 이동하는 변형 가능한 유한요소격자(transformable finite-element grid)를 사용하였다. 본 수치해석기법의 타당성 입증을 위해 극심한 열하중이 부여된 조건하에서 엄밀해가 존재하는 비정상 축대칭문제 및 고체로켓 노즐내열재에 대해 열해석을 수행하였으며, 그 결과 수치해는 엄밀해 또는 실험치와 잘 일치함을 보이었다. 여러 가지 복합재로 구성된 내삽노즐 또는 외삽노즐에 대해서도 안정된 수치해를 얻을 수 있었다. 아울러 노즐목삽입재로 탄소-탄소 복합재를 적용한 고체추진기관 내삽노즐을 해석모델로 택하여 열전달 해석을 수행하고 해석결과를 분석하였다. 노즐의 표면산화반응에 대한 열반응상수, 즉 Arrhenius 형태로 표시된 식에서 pre-exponential factor 및 activation energy 변화가 탄소-탄소 복합재 및 탄소-페놀릭 복합재의 삭마량에 미치는 영향에 대해서 고찰하였다.