• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.105-111
• /
• 2006

The aircraft engine is to generate thrust for the maneuver of aircraft and to provide the power to the related hydraulic system and electrical system. Since the power provided to the systems is extracted from the high pressure compressor of aircraft engine, the extracted power is called horsepower extraction (HPX). If the HPX provided from the engine is smaller than the HPX required from the related systems, there could be abnormal engine behavior, like engine rollback or stall. Analysis on comparing the required HPX and the engine HPX capability had been performed during the T/A-50 FSD (Full Scale Development) period. The analysis results make the engine schedule changed, and T/A-50 flight test has been performed with the changed engine schedule. The analysis results and changing the engine control schedule were verified to be valid with the flight test results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.6
• /
• pp.92-97
• /
• 2006

A critical speed analysis is performed for a 30 ton thrust turbopump considering the casing structural flexibility. A full three-dimensional finite element method including rotor and casing is used to predict rotordynamic behavior. Rotor alone model and rotor-casing coupled model with fixed-fixed and free-free boundary conditions are calculated to investigate the effects of the casing structural flexibility. The stiffness of ball bearings are applied as unloaded and loaded values to consider rotor operating conditions in vacuum and real engine respectively. From the results of the numerical analyses, it is found that the effect of the casing structural flexibility reduces the critical speeds of the turbopump. Especially, the loaded rotor condition with higher bearing stiffness is affected dramatically rather than the unloaded rotor condition with lower bearing stiffness.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2379-2384
• /
• 2015

Bellows product is an important part in the area of plant engineering, shipbuilding and petrochemistry. For safety and durability it is necessary to consider lots of factors when designing it. This research developed a U-shaped metal bellows design software based on EJMA 9th Edition manual. This GUI software was developed by using Matlab software and can be able to design four types of bellows, Unreinforced Single Bellows, Unreinforced Double Bellows, Reinforced Single Bellows and Reinforced Double Bellows. The already proven bellows model was designed to verify this software. We investigated the behavior while changing the thickness of the bellows. As the thickness of bellows increases, spring rate, thrust force, stress increase and fatigue life decreases. This software will be helpful design engineers save time and effort.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.3
• /
• pp.18-25
• /
• 2006

In order to perform system requirements quickly and accurately, an automatic design program of solid rocket motors(SRM) structure designated as the 'ProDes software' has been developed and verified. from given system design criteria and constraints, it has the capabilities to design, analysis, simulation and drawing process to greatly reduce the over 'design cycle time' and manpower of a project. The conception of the program is modular, and calculations are performed step by step allowing parametric design studies and providing final selected design goal. Each configurations of SRM components and joint types composed of various master models is obtained from the data base module of the library. Between the design results of the ProDes software and those of the previous detail design of the established motor showed good agreements.

• Journal of Aerospace System Engineering
• /
• v.11 no.5
• /
• pp.42-49
• /
• 2017

The solid rocket motor(SRM) consists of a motor case, igniter, propellants, nozzle, insulation, controller, and driving device. The liquid rocket propulsion systems(LRPSs) cools the nozzle by the fuel and oxidizer but SRM does not cool the nozzle. The nozzle of SRM is high temperature condition and high velocity condition so occurs the erosion by combustion gas. This erosion occurs the change of nozzle throat and reduces thrust performance of rocket. The material of Rocket nozzle is minimization of erosion and insulation effect and endure the shear force, high temperature and high pressure. The purpose of this study is to investigate the erosion characteristics of solid rocket nozzles by each combustion time. Through the structure inspection of Graphite and C-C composite, identify the characteristics of the microstructure before and after erosion.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.11
• /
• pp.1112-1120
• /
• 2009

In this paper, the authors introduced a new approach to find the target orbits of each satellite in order to establish a temporary reconnaissance constellation mission to minimize the average revisit time (ART) while satisfying the constraint on fuel limit. Two distinct problems are dealt with: the first is to reconnoiter the local area with discriminating fuel constraint the second is to reconnoiter ground moving target with same fuel constraint. A preliminary effort in applying a genetic algorithm to those problems has also been demonstrated through simulation study. The results show that current ARTs of each mission are reduced by 41% and 42%, respectively, by relocating the orbit of each satellite. Naturally, the final result may depend on satellite orbits, sensor characteristics, allowable fuel cost, thruster capability, and maneuver strategies.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.10
• /
• pp.677-690
• /
• 2022

By using an actuator disk method based flow solver, aerodynamic analysis is carried out for a dual ducted fan aircraft, which is one of the VTOL compound aircrafts, and its associated ground effect is analyzed. The characteristics and accuracy of the solver for ground effect analysis is evaluated through a comparison with the results obtained from the sliding mesh technique. The aerodynamic performance and flow field characteristics with respect to the distance from the ground are analyzed. As the ground distance decreases, the fan thrust increases, but the deterioration of total normal force and hovering flight efficiency is identified owing to the decrease in the vertical force of the duct, fuselage, and wing. By examining the flow field in the bottom of the fuselage, the ground vortices and fountain flow generated by the interaction of the fan wake and ground are identified, and their influence on the aerodynamic performance is analyzed. The strength and characteristics of outwash with respect to the ground distance and azimuth direction are analyzed through comparison/examination of velocity profile. Influence of the ground effect with respect to collective pitch angle is also identified.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.3
• /
• pp.1-12
• /
• 2015

During installing sheet piles for an impermeable wall or a retaining wall, vibratory hammers are widely used. Among vibratory hammers, a hydraulic hammer is used most commonly. However, a hydraulic hammer causes excessive vibration and noise due to resonance by change of natural frequency according to movements of eccentric shaft when the hammer starts and stops. In this study, new variable amplitude type hammer is developed in order to reduce the vibration and noise due to resonance produced in starting and stopping the hammer. By controlling horizontal angle in two pairs of eccentric body inside of the hammer, the amplitude and vibration of the new hammer can be controlled. The performance tests with the new hammer and existing hammers such as the hydraulic hammer and electric hammer are carried out, and the new hammer shows reduced vibration and noise results in comparison with existing hammers from performance tests. Also, this study shows that penetration rates of sheet pile using the new hammer increase due to impellent force of a backhoe in comparison with the electric hammer and penetration rate increase in comparison with a general hydraulic hammer, since the new hammer can control the amplitude during penetration of sheet pile according to soil condition.

• Tunnel and Underground Space
• /
• v.30 no.5
• /
• pp.484-495
• /
• 2020

To numerically simulate the advance of EPB TBM, various type of numerical analysis methods have been adopted including discrete element method (DEM), finite element method (FEM), and finite difference method (FDM). In this paper, an EPB TBM driving model was proposed by using coupled DEM-FDM. In the numerical model, DEM was applied in the TBM excavation area, and contact properties of particles were calibrated by a series of triaxial tests. Since the ground around the excavation area was coupled with FDM, the horizontal stress considering the coefficient of earth pressure at rest could be applied. Also, the number of required particles was reduced and the efficiency of the analysis was increased. The proposed model can control the advance rate and rotational speed of the cutter head and screw conveyor, and derive the torque, thrust force, chamber pressure, and discharging during TBM tunnelling.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.9
• /
• pp.765-772
• /
• 2015

Aerodynamic force measurements and phase-locked PIV study were carried out to check the bio-mimetic MAV applicability of a swift flight. Two-rotational DOF robotic wing model and blowing-type wind tunnel were employed. The amplitude of twist angle were ${\pm}0$, ${\pm}5$, ${\pm}10$, and ${\pm}20$ deg. and stroke angles were manipulated by simple harmonic function with out-of-phase in regards to the stroke motion. It is acknowledged that the time-varying lift coefficients in accordance with the change of the twist angle did not result in any noticeable differences, just the small decrease and delay. However, the drag exhibited that the small change of the twist angle can produce large thrust. These findings imply why a swift uses small twist angle during flight. The PIV results displayed that the delay of aerodynamic forces is highly associated with the vortical structures around the wing. It is therefore indicated that a process of designing a swift-based Micro Air Vehicle should take the twist angle into consideration, as the essential parameter.