• Journal of the Korean Geosynthetics Society
• /
• v.20 no.4
• /
• pp.19-32
• /
• 2021

In this study, evaluation and consideration of domestic/overseas design, construction, and quality control performed by the authors on the deep cement mixing method were performed, and improvements for the development of the DCM method were suggested in the future. As a result of this study, it was found that the cross-sectional area correction for strength is required during the laboratory test of mix proportion, and caution is required because the extrapolation method may lead to different results from the actual one. Applicable design methods should be selected in consideration of both the improvement ratio and the type of improvement during design, and it was confirmed that the allowable compressive strength to which the safety factor was applied refers to the standard value for stability review and not the design parameters. In the case of the stress concentration ratio, rather than applying a conventional value, it was possible to perform economical design by calculating the experimental and theoretical stress concentration ratio reflecting the design conditions. In the case where pre-boring is expected during construction, if the increased water content is not large compared to the original, there were cases where a major problem did not occur even if the result that did not consider the increase in water content was used. In addition, it was confirmed that when the ratio of the top treatment length to the improved length is high, a small amount of design cement contents per unit length can be injected during construction. In the case of quality control, it was evaluated that D/4~2D/4 for single-axis and D/4 point for multi-axis were optimal for coring of grouting mixtures. As an item for quality control, it is judged that the standard that considers the TCR along with the unconfined compressive strength of grouting mixtures is more suitable for the domestic situation.

• Journal of Animal Science and Technology
• /
• v.53 no.5
• /
• pp.441-450
• /
• 2011

This study was conducted to determine the effects of partial replacement of corn grain and soybean meal with agricultural by-product feeds on in vitro rumen fermentation characteristics and optimum levels of mixing ratio. The agricultural by-products to examine the effectiveness of the partial replacement of concentrate were wheat bran, corn gluten feed, bakery waste, soybean curd, rice bran, green kernel rice, soybean hull, distillers' grain, and mushroom substrate. In the first experiment, in vitro ruminal fermentation characteristics of feedstuffs were evaluated at 0, 3, 6, 12, 24, and 48 hours after incubation. In the second experiment, fermentation characteristics were investigated with green kernel rice and soybean curd which replaced corn grain or soybean meal. Feed were formulated with 40% corn grain + 20% soybean meal (T1), 40% corn grain + 17.5% soybean meal + 2.5% soybean curd (T2), 25% corn grain + 20% soybean meal + 15% green kernel rice (T3), and 30% corn grain + 15% soybean meal + 6% green kernel rice + 9% soybean curd (T4), respectively, with forage source of 10% alfalfa hay, 20% timothy hay, and 10% corn silage as fed-basis. In 24 and 48 hour cultivations, T4 showed significantly lower pH compared to T1, whereas in 3 and 24 hour cultivations, T4 showed significantly higher DM degradation compared to T1. In addition, the gas production of T3 was also higher than T1 (p<0.05). Overall results of the present experiments indicated that green kernel rice and soybean curd as agricultural by-products have the possibility of partial replacements of corn grain and soybean meal.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.20 no.1
• /
• pp.35-47
• /
• 2018

A edible mushroom, Clitocybe maxima (Lentinus giganteusis) commercially cultivated in China and Taiwan. However, the researches of cultivation and cultural characteristics were not reported in Korea. In this study, we conducted on cultural characteristics and artificial cultivation of C. maxima. Six isolates were collected from China(3 isolates, commercial strain), Taiwan(1 isolate, commercial strain) and Korea(2 isolates, wild type). C. maxima and L. giganteus collected in China and Taiwan, respectively, are the same in China and are estimated to be of the same species as cultured characteristics. The mycelial growth of the collected strains was not significantly different in agar medium but it showed the best growth in YPMG in liquid culture. Optimum temperature for mycelial growth and induction of fruit body were 25℃ and 30℃, respectively. In order to artificial cultivation of C. maxima, cultural characteristics and artificial cultivation were carried out using agricultural by-products and forestry by-products materials. Mycelial growth was suitable in rice straw, cottonwood sawdust, corncob and rice seed medium, and it was selected as a cultivation medium. The suitable medium for artificial cultivation of C. maxima was selected to mixed medium 2(compounding ratio(v/v): 55% of hardwood sawdust, 5% of cottonseed pellets, 10% of cottonseed, 15% of beet pulp, 15% of swollen rice husks). It took about 30 days to be able to harvest, it was faster than oyster mushrooms. The cultivation period was about 30days. A isolate, CMA-002 was not initiation to fruit body primordiuma on the used cultivation substrate. Other 5 isolates were initiate and development to fruit body on the substrate used in this study. The strain CMA-003 was initiated to be fruiting body by 8~10 days after induction of fruiting body in all of the substrates. Isolate CMA-003 was generate to a bundle fruit body. Other isolates, however, were form fruit body individually. The CMA-003 strain was likely highly recommendable strains for farming. The optimum conditions for the induction and growth of C. maxima fruit body were 25~30℃, 8 hr illumination per day with white fluorescent lamp, 90~95% relative humidity, and 1,500 ppm of CO₂ concentration in a cultivation room.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.9
• /
• pp.636-642
• /
• 2013

In order to overcome drawbacks (i.e., filtration and recovery) of conventional powder type photocatalysts, nano-ZnO/Laponite/PVA (ZLP) photocatalyzed adsorption balls were developed by using in situ mixing of nanoscale ZnO as a photocatalyst, and Laponite as both adsorbent and supporting media in deionized water, followed by the poly vinyl alcohol polymerization with boric acid. The optimum mixing ratio of nano-ZnO:Laponite:PVA:deionized water was found to be 3:1:1:16 (by weight), and the mesh and film produced by PVA polymerization with boric acid might inhibit both swelling of Laponite and detachment of nanoscale ZnO from ZLP balls. Drying ZLP balls with microwave (600 watt) was found to produce ZLP balls with stable structure in water, and various sizes (55~500 ${\mu}m$) of pore were found to be distributed based on SEM and TEM results. In the initial period of reaction (i. e., 40 min), adsorption through ionic interaction between methylene blue and Laponite was the main removal mechanism. After the saturation of methylene blue to available adsorption sites for Laponite, the photocatalytic degradation of methylene blue occurred. The effective removal of methylene blue was attributed to adsorption and photocatalytic degradation. Based on the results from this study, synthesized ZLP photocatalyzed adsorption balls were expected to remove recalcitrant organic compounds effectively through both adsorption and photocatalytic degradation, and the risks of environmental receptors caused by detachment of nanoscale photocatalysts can be reduced.

• The Korean Journal of Food And Nutrition
• /
• v.23 no.2
• /
• pp.218-225
• /
• 2010

To make sponge cake using Lentinus edodes powder, which is useful and valuable as a functional food material, we tested samples with 3, 6, 9, and 12% L. edodes powder to ascert200ain the quality characteristic and make optimize preparation. Samples and L. edodes powder-free control sponge cakes were compared in terms of quality characteristics including batter viscosity and specific gravity, moisture content, volume index, weight, color, textural characteristics, and sensory qualities, to determine the optimal ratio of L. edodes powder in the formulation. Viscosity and specific gravity of sample and control batter were not significantly different. Moisture content of the sample and control sponge cake also did not differ significantly, and weight of sample and control sponge cakes did not differ appreciably. The volume index of the samples displayed contrasting values, increasing with 3~6% L. edodes powder and decreasing with 9~12% powder. L, a, and b crust color values of samples sponge cakes were lower than those of control cakes. The L and a values of the control cakes was maximal, with values progressively decreasing with incorporation of more L. edodes powder. The b value decreased by 3% with the addition of up 6% L. edodes powder with no further decrease thereafter. L. edodes powder was the lower value. So was the color a, and L. edodes powder increased, a-values decreased. 3% difference was shown in b, the color and none between the samples with 6~12%. L. edodes powder showed lower values making a comparison with the control. Hardness and fracturablility were not appreciably affected by 3% L. edodes powder, but was affected by concentrations 6%. Fracturability og sample sponge cakes was consistently lower than control cakes. Fracturability made little difference in 3% samples, but it was not the same with more than 6% L. edodes powder samples; the samples showed lower value than the control. Adhesiveness was not significantly affected. Chewiness was lower in all sample cakes except those prepared with 3% L. edodes powder. Use of L. edodes powder conferreds higher resilience values as compared to thecontrols. Sensory attributes of color, flavor, softness and overall acceptability were the highest in control sponge cakes, as the amount of L. edodes powder increased, the acceptability decreased. L. edodes-flavor, pleasant taste and off-flavor were the lowest in control cakes, and values increased as the amount of L. edodes powder increased. The control sponge cakes showed the highest values in egg-flavor and moistness, which progressively increased as added L. edodes powder increased. The results indicate that control sponge cakes displayed were. the highest overall acceptability, with acceptability decreasing and it decreased as L. edodes powder content increased. However, 3~6% L. edodes powder can produce an acceptable product, and may be used as anoptimized mixture ratio.

• Journal of the Korea Concrete Institute
• /
• v.13 no.1
• /
• pp.30-37
• /
• 2001

Generally, polymer mortar made with unsaturated polyester(UP) resin has a high curing shrinkage. This is an inadequate as repair material and construction products that have been widely used for years recently. To overcome these problems, polymer researchers and engineers have used shrinkage-reducing additives, which are usually specific thermoplastic polymers. The objective of this study is to evaluate the effects of shrinkage-reducing additive on the curing shrinkage and strengths of UP mortar. UP mortars are prepared with expanded polystyrene(EPS) ratio in styrene monomer(SM), (EPS/PS, PS=EPS+SM), and the ratio of total polystyrene resin(PS) to UP resin, (PS/UP). And it is tested for viscosity of UP resin, slump-flow, working life, flexural and compressive strengths, and curing shrinkage tests. From the test results, viscosity of resin for UP mortar increases with increasing PS content. Curing shrinkage of UP mortar is considerably smaller than that of plain UP mortar, nevertheless, reduction in the strengths is not recognized according to adding PS resin. In this study, we can obtain the optimum mix proportions of UP mortar using PS resin which made of waste expanded polystyrene.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.4
• /
• pp.331-339
• /
• 2017

The purpose of this study is to evaluate the effect of curing age and thickness of coating material on the bond strength of polymer cement slurry(PCS)-coated rebar that can replace epoxy-coated rebar. The test specimens were prepared with two types of cement, two types of polymer dispersion as St/BA and EVA, two polymer-cement ratios, two coating thicknesses and three curing ages, and tested for bond strength test to cement concrete. The flexural behavior of RC beam that is made by optimum conditions such as polymer-cement ratio of 80%, coating thickness of $100{\mu}m$ and curing age of 7 days of PCS recommended from the bond strength test is also conducted. From the test results, The maximum bond strength of PCS-coated rebar at curing age of 7-day and coating thickness of $100{\mu}m$ was about 1.52 and 1.58 times respectively, the strength of plain and epoxy-coated rebar. The ultimate loads of RC beam using PCS-coated rebar were range of 81.1% to 102.3% of that of plain rebar, and 98.4% to 124.1% of that of epoxy-coated rebar. It is apparent that PCS-coated rebar with EVA, curing age at 7-day and $100{\mu}m$ can replace epoxy-coated rebar in construction field.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.2
• /
• pp.497-505
• /
• 2017

TDF (Tire derived fuel) Fly ash is an industrial by-product when scraped tire was used a fuel source at the power plant. TDF Fly ash has been classified as domestic waste at the workplace so far and has not been appropriately utilized. We conducted a fundamental physical property test of asphalt mixture to investigate the possibility of using TDF Fly ash as a mineral filler of asphalt mixture for exploring new usage strategies. TDF Fly ash meets KS F 3501 asphalt mixture mineral filler criteria. And the optimal asphalt binder amount was determined to be 4.5% by Marshall design. Mineral filler content was determined at 3% and analyzed by comparing using mineral filler as stone powder. The basic physical property test of the asphalt mixture was evaluated to the provision indicated in "Production and Construction Guidelines for Asphalt Mixture" published by the Ministry of Land, Infrastructure and Transport. In the test, Marshall stability test, dynamic immersion test, tensile strength ratio test, wheel tracking test were carried out. As a result of the experiment, Marshall stability and dynamic stability satisfied the standards, and confirmed the stability and Dynamic immersion and tensile strength ratio test that TDF Fly ash is more effective for scaling and moisture resistance than stone dust. Therefore, in this research, it is expected that multilateral utilization of TDF Fly ash, and a positive effect can be also expected.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.1
• /
• pp.23-34
• /
• 2022

The purpose of this study is to evaluate the adhesion properties of polymer cement composites for crack repair of an RC structure. Polymer cement composites are manufactured from cement, three types of polymers and silica fume, and the mixture is designed by adjusting the water cement ratio and AE reducing agent so that the viscosity target of the polymer cement composites is 700mPa·s or less. According to the test results, the Type-A adhesion in tension of the polymer cement composite exceeded the adhesion standard of 1.0MPa of the polymer finishing material, and furthermore, depending on the type of polymer, the adhesion in tension was highest for SAE, followed in descending order by EVA, and SBR. In addition, the adhesion in tension of Type-B is up to 1/4.5 lower than that of Type-A, but the incorporation of silica fume shows a significant improvement in terms of adhesion in tension. Based on this study, the basic mixing design of the polymer cement composites required for viscosity and adhesive performance required for crack repair of the RC structure was completed. It could be proposed as an optimal mixing design under conditions for intermixing polymer type EVA, SAE, and P/C 80%-100%.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.5
• /
• pp.5-12
• /
• 2018

The porosity formation by the addition of additives was found to be the highest in the case of aluminum powder 3% and $Ca(OH)_2$ 2% under the condition that strength was maintained. The optimum mixing ratio of the binder was shown to be the most effective at (Ash+Food waste+clay):(water glass+colloidal silica) 7:3, and the temperature response is most economical and effective at $1,000^{\circ}C$. The optimal mixing ratio is the strength in 30% of ash, 30% of clay and 10% of food waste, which is the effective in non-point pollution water treatment. Filter media produced under optimal mixing conditions were analyzed as $SiO_2$ 65.8%, density $1.4g/cm^3$, porosity 25.6%, pH 9.8, and no hazardous substances were detected. As a result of the filtration of the water treatment, the mean concentration of the filtered SS was $14.06mg/{\ell}$, and the removal efficiency of SS was 90%, the recovery rate of the reversal is 97.1%. This enables the development of filter media considering economic efficiency and efficiency as well as the utilization of waste resources, enabling high value added of waste resources.