• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.3
• /
• pp.362-367
• /
• 2012

Though a micro pump is a crucial element in miniaturized bio-fluidic systems or drug delivery systems, most of the conventional micro pumps still have some limitations to miniaturize their controller system and to obtain the sufficient back pressure which can rise over the inner pressure of human body or experimental animals. In this paper, to overcome these limitation, a new PZT disc and its controller were designed and fabricated to get the sufficient flowrate and the back pressure with guaranteeing embeddability of the controller into pumping body. The amplitudes of the disc deflections were as large as 40 ${\mu}m$ at 200 V - 100 Hz condition. As results of experiments, the flow rate and the back pressure increase when the frequency increases. The obtainable maximum flow rate and back pressure are 5.2 ml/min at 95 Hz and 13.14 kPa at 90 Hz respectively.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2004.11a
• /
• pp.253-257
• /
• 2004

디지털 TV 방송이 본격적으로 보급됨에 따라 2004 년 후반부터 각 방송사들은 디지털 방송네트워크의 설계를 위해 본격적인 전계강도 실측을 실시하고 있다. DTV 신호 측정에는, 가장 기준이 되는 전계강도 측정기를 비롯하여 DTV 복조기(demodulator), 각종 셋톱박스, 위성항법장치(GPS)를 이용한 지형정보시스템(GIS) 등 많은 장비가 필요하고 측정항목도 다양하여, 한 지역을 측정하는데 많은 시간이 소요될 뿐 아니라 측정자의 숙련도에 따라 측정결과의 정확도와 신뢰도가 떨어질 수 있다. 본 논문에서는 이러한 문제들을 해결하기 위해 다양한 계측장비와 운용장비의 제어를 체계적으로 관리하고 측정절차를 일반화하며 측정결과 데이터를 데이터베이스화하여 측정결과를 용이하게 파악할 수 있는 통합 측정 시스템을 제안한다. 또한, 본 시스템은 측정 뿐 아니라 지형정보시스템과 전계강도 예측시스템을 도입하여 측정지점 주변의 수신환경 분석 및 최적 수신위치의 검색정보 등을 제공하며, 다량의 측정결과에 대한 다양한 분석이 가능하여 커버리지 분석 및 송신 네트워크의 설계 등에 활용될 수 있다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.109-112
• /
• 2005

As the degree of use of network is increasing the need for building the basic of the stable network service is being needed a lot. Also the engineers require the traffic control for the best application and management and bandwidth management urgently. To solve these problems, there were no other ways of increasing the bandwidth of lines until now. However, this solution has the limit that the cost is too high and the traffic problem is growing continuously. On this study, it is suggested that through the planning the wired /wireless combination network design offering the service of QoS, Multicast, Mobile, realtime multimedia traffic delay without packet loss will be dealth with.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.10A
• /
• pp.1604-1612
• /
• 2000

This paper proposes a simultaneous hardware resource allocation and binding algorithm for VLSI design. The proposed algorithm works on scheduled input graph and simultaneously allocates binds functional units, interconnections and registers by considering interdependency between operations and storage elements in each control step, in order to share registers and interconnections connected to functional units, as much as possible. Also, the register allocation is especially executes the allocation optima us-ing graph coloring techniques. Therefore the overall resource is reduced. This paper shows the effectiveness of the proposed algorithm by comparing experiments to determine number of functional unit in advance or to separate executing allocation and binding of existing system.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12a
• /
• pp.269-272
• /
• 2011

주물 사업장의 용해 공정인 장입과 출탕 작업, 첨가제 투입 과정에서 많은 분진이 발생한다. 실제 주물 사업장에서 사용되는 후드 형태는 매우 다양하며 구조적인 문제점으로 인해 효과적인 배기가 어려운 실정이다. 본 연구를 통해 실제 사업장에 전기로의 다양한 공정 형태에 대한 대응이 가장 우수한 직인식 후드 방식을 제시하고, 전산유체역학(CFD : Computational Fluid Dynamics)을 이용한 오염물질 거동 예측 기법을 활용하여 직인식 후드의 적정 배기량을 산정하여 현장에 제시하였다. 실제 현장에서는 본 개념 설계 결과를 바탕으로 용해 공정에 $400m^3/min$의 배기량을 갖는 직인식 후드를 설치한 결과, 매우 만족스러운 분진 제어 효율을 확인할 수 있었다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.1
• /
• pp.127-132
• /
• 2019

In this paper, we design and build an information system for the growth management of agricultural products and aquatic products by ubiquitous computing. So that, we installed various sensor systems and developed IP Cam to establish monitoring. It was possible to construct an environmental management system based on IT technology by a database that directly controls and manages the growth conditions of agricultural products and aquatic products by monitoring. We have installed various sensors that can acquire data in real time and IP Cam is designed and manufactured in three parts. It was applied to agricultural and marine products and monitored soil moisture, temperature, and environmental information to establish conditions for growth environment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.1-8
• /
• 2019

The optimal design parameters of a dynamic absorber (DA) in a machine body (that is considered as a rigid body) are discussed in this paper. The bounce and rotation motions of the rigid body have been controlled passively by a DA, which consists of a mass and a spring. The rigid body is subjected to a harmonically excited force and supported by linear springs at both ends. To define the motion of a rigid body with a DA, the equation of motion was expressed in the third-order matrix form. To define the optimal design conditions of a DA, the reduction of dynamic characteristics, represented by the amplitudes of bounce and rotation, and the transmitted powers, were evaluated and discussed. The level of reduction was found to be highly dependent on the location and spring stiffness of the DA.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.5A
• /
• pp.433-442
• /
• 2010

A control of chloride diffusion coefficient is very essential for service life of reinforced concrete (RC) structures exposed to chloride attack so that much studies have been focused on this work. The purpose of this study is to derive the intended diffusion coefficient which satisfies intended service life and propose a technique for optimum concrete mixture through genetic algorithm(GA). For this study, 30 data with mixture proportions and related diffusion coefficients are analyzed. Utilizing 27 data, fitness function for diffusion coefficient is obtained with variables of water to binder ratio(W/B), weight of cement, mineral admixture(slag, flay ash, and silica fume), sand, and coarse aggregate. 3 data are used for verification of the results from GA. Average error from fitness function is observed to 18.7% for 27 data for diffusion coefficient with 16.0% of coefficient of variance. For the verification using 3 data, a range of error for mixture proportions through GA is evaluated to 0.3~9.3% in 3 given diffusion coefficients. Assuming the durability design parameters like intended service life, cover depth, surface chloride content, and replacement ratio of mineral admixture, target diffusion coefficient, where exterior conditions like relative humidity(R.H.) and temperature, is derived and optimum design mixtures for concrete are proposed. In this paper, applicability of GA is attempted for durability mixture design and the proposed technique would be improved with enhancement of comprehensive data set including wider range of diffusion coefficients.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.6
• /
• pp.41-46
• /
• 2019

In this paper, it is necessary to study the bandwidth and network system for efficient image transmission in the current era of drone imaging, and to design routing protocols to round out and cluster two or more multi-drones. First, we want to construct an ad hoc network to control the multidrone. Several studies are underway for the clustering of drones. The aircraft ad hoc network (FANET) is an important foundation for this research. A number of routing protocols have been proposed to design a FANET, and these routing protocols show different performances in various situations and environments. The routing protocol used to design the FANET is tested using the routing protocol used in the existing mobile ad hoc network (MANET). Therefore, we will use MANET to simulate the routing protocol to be used in the FANET, helping to select the optimal routing protocol for future FANET design. Finally, this paper describes the routing protocols that are mainly used in MANET and suitable for FANET, and the performance comparison of routing protocols, which are mainly used in FANET design.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.1 s.104
• /
• pp.24-38
• /
• 2006

In this paper, we investigate the design and fabrication of a conical spiral antenna suitable for satellite TT&C applications. The shape of the spiral is optimized using a commercial electromagnetic software for good gain and axial ratio performances over $2.0{\sim}2.3\;GHz$ frequencies. A coaxial infinite balun feeding the spiral is designed using experimental methods. A method for precision fabrication of the spiral is presented. Measurements of the fabricated antenna show satisfactory performances over $2.0{\sim}2.3\;GHz$ such as a reflection coefficient less than -18 dB, a maximum gain greater than 4 dB, a gain greater than 0 dB over angles ${\pm}75^{\circ}$ from the antenna boresight, an axial ratio less than 5 dB over angles ${\pm}90^{\circ}$ from the antenna boresight, a front-back ratio greater than 15 dB.