• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.22-28
• /
• 2007

Using woodceramics made from sawdust board of pine thinning logs, changes in surface temperature were investigated, by the heating rate and keeping time at maximum temperature. The heating rate of $2^{\circ}C/min$ and keeping time at maximum temperature 1 hour, were the highest in surface temperature. Also, it was found that woodcermics maintained heat for a long time because the descending velocity of their surface temperature was slower than that of the heater.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.38-44
• /
• 2005

This research investigated the variation of density, the weight loss, dimensional shrinkage and heat conduction by the heating rate and keeping time at maximum temperature of woodceramics, when sawdust boards made from thinned logs of Pinus densiflora, Larix kaemferi and Pinus koraiensis were impregnated with phenol-formaldehyde resin, and then were formed by heating rate ($2^{\circ}C/min{\sim}6^{\circ}C/min$) and keeping time at maximum temperature (1~5 h). As the heating rate increased, the density and thickness shrinkage decreased, but weight loss and linear shrinkage increased. The more the keeping time at maximum temperature, the greater the linear shrinkage and thickness shrinkage. The heating conduction was superior at the heating rate is $2^{\circ}C/min$ and the keeping time at maximum temperature of 2 hs.

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.141-148
• /
• 2017

This study is experimentally investigated the effects of various steam curing parameters on the early-age compressive strength development of high strength concrete (over 40 MPa) in the precast plant production. High strength concrete are used only ordinary portland cement (type I) and water-cement ratio selected 3cases (25%, 35% and 45%). Also, steam curing parameters are as followings ; (1) Preset period 2cases (3 hours and 6 hours) (2) Maximum curing temperature 3cases ($45^{\circ}C$, $55^{\circ}C$ and $65^{\circ}C$) (3) Maintenance time of curing temperature 3cases (4 hours, 6 hours and 8 hours) (4) Maximum rate of heating and cooling $15^{\circ}C$/hr. Initial setting time and adiabatic temperature rising ratio of these concrete according to water-cement ratio are tested before main tests and examined the compressive strength development for the steam curing parameters. Also compressive strength are compared with optimum steam curing condition and standard curing at test ages. As test results, the optimum steam curing conditions for high strength concrete(over 40 MPa) are as followings. (1) Preset period ; over initial setting time of concrete (2) Maximum curing temperature ; bellow $55^{\circ}C$ (3) Maintenance time of curing temperature ; bellow 6hours. Also strength development of steam curing concrete show in the reversed strength at 28 days. It is to propose an efficient steam curing condition for high strength concrete in the precast method.

• Korean journal of applied entomology
• /
• v.60 no.2
• /
• pp.203-214
• /
• 2021

This study aimed at establishing a packaging standardization method that allows the maintenance of biological control agents product quality during delivery. First, based on the results of distribution status analysis of biological control agent products from four manufacturers, we confirmed that the mean temperature was maintained at 25.6℃ (minimum and maximum temperatures.: 18.1 and 30.7℃, respectively) inside the packaging box of each company for 36-48 h. To establish the optimal packaging method for each season, seven external temperature conditions were set ranging between 0℃ and 30℃ at intervals of 5℃. In addition, we evaluated internal temperature maintenance performance for each coolant pack handling method and determined 14 packaging combinations. A packaging combination that maintained a temperature of 3℃ - 9.9℃ at each external temperature conditions was considered efficient. This temperature range is close to a lower developmental threshold at which the biological control agents can survive with minimum energy for 12 h (direct delivery time), or 36-48 h (general delivery time) after packaging.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.25 no.3
• /
• pp.117-123
• /
• 2019

The general Impulse Sealer has a problem of sealing quality because continuously sealing process results in an undesirable temperature rise, which may accumulate the heat during the operation. In order to address such a drawback, the controlled sealing temperature method can be effectively utilized compared with the general controlled time method. As such, a temperature sensor with capability of detecting the sealing temperature was installed, and a separate PCB was manufactured to control the sealing temperature by measuring and calculating the detected temperature. The temperature changes during the temperature rise and maximum temperature after continuously operation were investigated using an Impulse Sealer system. Next, the results obtained from experiment were compared with each other. As such, the maximum temperature was 70.3℃, whereas 8.9℃ was recorded as control temperature. It implies that this controlled temperature system prevented the undesirable temperature rise, thereby causing a consistent sealing quality.

• Food Science and Preservation
• /
• v.10 no.3
• /
• pp.370-375
• /
• 2003

To obtain the oil sesame, walnut, whole wheat, and rice bran were extracted for 1, 3, or 6 hr by a shanking water bath(35$^{\circ}C$ and 100 rpm), and by soxhlet extractor(80$^{\circ}C$) for 1, 3 or 6 hr, respectively. The highest yield of extracted oil was obtained from the walnut(63.07％ weight) and the whole wheat showed the lowest extraction yield of oil(1.13％ weight). Major fatty acids from the extracted oils were linoleic, oleic, and palmitic acid. The maximum contents of total phytosterol in sesame, walnut, whole wheat, and rice bran were 0.44, 1.57, 2.25, and 2.03(％ weight), respectively. Besides, total tocopherol contents in sesame, walnut, whole wheat, and rice bran were maxima 3.42, 0.16, 2.92, and 0.07(％ weight), respectively. From the extracted oils, structured lipids(SL) were synthesized by the interesterification reaction with conjugated linoleic acid(CLA) in a shanking water bath at 55$^{\circ}C$. When the reactions(1:3 substrate molar ratio, extracted oil:CLA) were conducted for 24 hr, maxima 23.75 mol％ of CLA incorporation was obtained from walnut oil and, in other cases, 16.28 - 19.15 mol％ of CLA was found in the produced SL triacylglycerol molecules.

• Journal of Animal Environmental Science
• /
• v.9 no.2
• /
• pp.79-84
• /
• 2003

1.퇴비 온도의 상승에 비례하여 폐사계 체내의 온도도 상승하여 퇴적식 퇴비단의 경우 $55^{\circ}C$내외의 고온지속기간이 약 30일정도 유지되었다. 반면에 토양 중에 매립된 폐사계의 체내 온도는 발효 전 기간 동안 $30^{\circ}C$ 이상으로 상승하지 못한 채 주변토양 온도와 거의 비슷한 수준을 유지하였다. 토양온도는 외기온의 변화에 즉각적인 반응을 보이지 않았다. 2. 시험용 발효조 내에서의 송풍여부에 따른 퇴비의 발효온도 변화추이는 송풍 처리구에서는 퇴비화 3일째에 최고온도 $68^{\circ}C$를 기록한 반면에 무송풍구에서는 퇴비화 5일째에 최고온도 $72^{\circ}C$를 기록하였다. 3. 퇴비단 표층에서 채취된 시료에서 검출된 $H_2S$와 $CH_3$SH 농도는 송풍 처리구에 있어서는 퇴비화 개시 후 20일 경과 후 각 각 28.5, 16.0 ppb 수준을 나타냈고 35일 경과 시에는 각각 57.7, 11.7 ppb, $CH_3SH$의 경우에는 23.7, 9.9 ppb 수준의 발생량을 기록하는 등 전반적으로 송풍처리구가 무송풍 처리구에 비해 악취가스의 발생량이 상대적으로 낮았다. 4. 폐사계를 밀폐용기 내에서 발표 시 수거된 침출수 중의 미생물 수가 토양매립 상태 하에서 수거된 침출수 중의 미생물 수보다 더 적은 경향을 보이고 있다. 5. 퇴비단 내에서 발효에 따른 폐사계 중량은 최초 3일간에 급격히 감소하고 시간의 경과에 따라 그 감소속도는 줄어든다. 발효온도가 높을수록 조직의 분해속도가 빨라지고 폐사계의 중량감소 속도도 빨라졌다. 6. 일반 퇴비와 폐사계를 발효시킨 퇴비 사이에 비료성분과 중금속 함량의 유의적인 차이는 발견되지 않았다.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.55 no.4
• /
• pp.339-349
• /
• 2010

The uses of the polypropylene bulk bags having the loading capacities more than 500 kg are increasing in Korea recently as a storage container for rough rice. This study was performed to obtain the basic information on the changes of temperature and relative humidity in the bulk-bag-stored high moisture rough rice during waiting for drying. At the moisture content more than 22% on wet weight basis of paddy, the bulk-bag inside temperature rose up to more than $40^{\circ}C$ and then slid down during storage. For example, in case of Hwaseongbyeo, 26.5% moisture content of rough rice (MCRR) harvested at 46 days after heading (DAH) showed $54.5^{\circ}C$ of peak temperature at 66.8 hours after bulk-bag loading, 22.5% MCRR harvested at 52 DAH exhibited $42.0^{\circ}C$ at 81.1 hours, and 19.7% MCRR harvested at 55 DAH displayed $38.9^{\circ}C$ at 119.0 hours. There were a good linear relationship between peak temperatures of bulk-bag inside and moisture contents of paddy ($r^2$=0.89 in 2005, and 0.87 in 2006), while the slope and intercept of the linear regression equation was affected by the environmental conditions such as ambient temperatures and microbial flora. The peak temperatures increased with the rate of about $2.74-3.33^{\circ}C$ per every 1% increase of moisture content at higher moisture contents of paddy than 19%. The relative humidity varied depending on bulk-bag inside temperature and rough rice moisture content, and showed the range of 94.2% to 99.9% in the central point of the bulk-bag. The results suggested that a rapid drying treatment as soon as possible was needed to produce a good quality of rice when the paddy of high moisture more than 22% on wet basis was harvested in a bulk-bag especially at high ambient temperature.

• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.280-291
• /
• 2023

Purpose: As fire accidents happen at the production and storage sites of superabsorbent polymers for convenience of daily life, an experimental study was conducted to secure basic data to establish practical preventive measures against them. Method: The sample container (20cm width × 20cm length) was made into a rectangular cuboid with the heights of 3cm, 5cm, 7cm, and 14cm, respectively, to allow access to the infinite flat plane. The front and back of the container were covered with a 300-mesh stainless steel mesh for one-dimensional heat transfer. The sample container was placed in the center of the thermostatic bath, which was heated to a predetermined temperature by setting the thermostat program in advance, and it was determined to be 'ignited' when the central temperature of the sample rose by more than 20℃ above the set temperature, and "unignited" when it was maintained at an approximate value of the set temperature. Result: The critical autoignition temperature was calculated to be 217.5℃ when the height of the sample container was 3 cm, 212.5℃ when it was 5 cm, 202.5℃ when it was 7cm, and 187.5℃ when it was 14cm. The ignition induction time to reach the maximum temperature was 34hours for 3cm, 76hours for 5cm, 143hours for 7cm, and 318hours for 14cm. Conclusion: ① As the size of the container increased, the autoignition temperature decreased and the induction time to reach the maximum temperature increased. ② An apparent activation energy was calculated to be 44.92kcal/mol, with a correlation of 96.93%.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.9-18
• /
• 1999

In this study, Metallugical properties between Sn-3.5Ag, Sn-37Pb eutectic solders and Au/Ni/cu substrate according to time span above the melting point were investigated. A conventional reflow soldering machine wert used for this study and time span above the melting point was determined by changing peak soldering temperature and conveyor speed. As results, scallop type intermetallic compounds of $Ni_3Sn_4$ were formed at joint interface and no Cu-Sn compounds were found at all; Ni layer performed as a barrier for Cu diffusion. As the peak soldering temperature increased, thickness of the intermetallic compound layer increased; maximum thickness of the scallop-layer was 2.2$\mu\textrm{m}$. The shape of scallops were transformed from hemi-sphere type to elliptical shape with smaller size. Micro-hardness of the solder joint decreased as the eutectic structure of Sn-3.5Ag and Sn-37Pb increased.