• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.7-10
• /
• 2000

본 논문은 이동통신상에서 송신측의 송신 채널 에러정보를 수신측에서 송신측으로 전달하는 음성패킷을 이용하여 송신측에 알려주어 압축과정에 이용하게 할 수 있는 방법을 제안한다. ACELP(Algebraic CELP)구조 방식을 가지고 있는 음성압축기들 중 G.729을 사용하며 음성 패킷정보 중 Pitch Delay와 Fixed Codebook를 이용하여 전송음성 패킷안에 상대방의 송신 채널정보를 싣는다. 수신측에서 받은 패킷이 Erasure로 판단되었을 때 패킷정보들 중 Fixed Codebook Index를 만들게 되는 4개의 Optimal 펄스 중 2개의 펄스만 사용하며 나머지 2개의 펄스는 약속된 임의의 위치에 위치시킨 후 송신측에 전송시킨다. 상대방에서 약속에 맞는 위치의 펄스를 보내왔을 때를 체크함으로써 자신의 송신채널 상태를 알 수 있게 된다 송신채널에$5\%$ Erasure 채널 에러가 발생했을 때 채널정보를 가진 패킷의 음질은 약 0.1dB 정도 떨어지게 된다. 하지만 음성압축 전송 시 송신채널의 정보를 이용하여 무선채널에러에 강하게 할 수 있다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.3
• /
• pp.17-24
• /
• 2013

In this paper, the measurement data is analyzed and channel characteristics are derived through MIMO Channel measurements at 781MHz considering antenna correlation. 781MHz frequency band currently operates the DTV system, however, it will be allocated new mobile communication frequency band. The channel characteristics at 781MHz seem to be similar existing mobile communication system at 900MHz but quite a different part of the existing research has demonstrated. In addition, the signal procedure of the channel characteristics, considering the correlation of the antenna, for a more accurate prediction research is needed. To avoid interference with Korean DTV broadcasting, we measured channel characteristics in urban areas of Jeju island by channel sounder and $4{\times}4$ antenna. Channel characteristics with antenna correlation were derived based on the measured data in the urban area.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.11
• /
• pp.2543-2551
• /
• 1997

This paper proposes a compression technique of image data, a variable length PN code and channel models which are required in CDMA communication system. It also analyzes their performances. Original images is compressed by 2-D DCT and its coefficients are quantized by optimal quantizer at compression rate 0.84bit/pel. Channel model 1 and 2 which are composed of 5 and 4 channels respectively are employed to be used in CDMA. Such a situation forces us to empoly variable length PN code, such as Chebyshev map for spread spectrum system. When average PN code length of model 1 and 2 is 44.4 and 26.7 chips respectively, the received image through these models under Gaussian noise with variance 1.75 is visually of the same quality as the transmitting image. Thus, the model 2 appears to be better in channel efficiency, comparing with channel model 1 and channel model which uses fixed length PN code.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1257-1264
• /
• 2019

A 3-GSymbol/s/lane transceiver, which supports the mobile industry processor interface (MIPI) C-physical layer (PHY) specification version 1.1, is proposed. It performs channel mismatch correction to improve the signal integrity that is deteriorated by using three-level signals over three channels. The proposed channel mismatch correction is performed by detecting channel mismatches in the receiver and adjusting the delay times of the transmission data in the transmitter according to the detection result. The channel mismatch detection in the receiver is performed by comparing the phases of the received signals with respect to the pre-determined data pattern transmitted from the transmitter. The proposed MIPI C-PHY receiver is designed using a 65 nm complementary metal-oxide-semiconductor (CMOS) process with 1.2 V supply voltage. The area and power consumption of each transceiver lane are 0.136 ㎟ and 17.4 mW/GSymbol/s, respectively. The proposed channel mismatch correction reduces the time jitter of 88.6 ps caused by the channel mismatch to 34.9 ps.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.7
• /
• pp.694-700
• /
• 2013

Urban area is a representative environment of wireless channels in the mobile communication, building density has a different distribution depending on the location. Building density has affect to propagation prediction For this reason, building density is expected to affect to the channel characteristics, we need to analyze it. We measured channel characteristics in urban areas of Jeju island by channel sounder and $4{\times}4$ antenna. Channel characteristics considering the building density were derived based on the measured data in the urban area. In this paper, the measurement data is analyzed and channel characteristics are derived through MIMO Channel measurements at 700 MHz considering the building density in the urban area.

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.818-823
• /
• 2015

In this study, FT reaction in a microchannel was simulated using computational fluid dynamics(CFD), and sensitivity analyses conducted to see effects of channel geometry variables, namely, process channel width, height, gap between process channel and cooling channel, and gap between process channels on the channel temperature profile. Microchannel reactor considered in the study is composed of five reaction channels with height and width ranging from 0.5 mm to 5.0 mm. Cooling surfaces is assumed to be in isothermal condition to account for the heat exchange between the surface and process channels. A gas mixture of $H_2$ and CO($H_2/CO$ molar ratio = 2) is used as a reactant and operating conditions are the following: GHSV(gas hourly space velocity) = $10000h^{-1}$, pressure = 20 bar, and temperature = 483 K. From the simulation study, it was confirmed that heat removal in an FT microchannel reactor is affected channel geometry variables. Of the channel geometry variables considered, channel height and width have significant effect on the channel temperature profile. However, gap between cooling surface and process channel, and gap between process channels have little effect. Maximum temperature in the reaction channel was found to be proportional to channel height, and not affected by the width over a particular channel width size. Therefore, microchannels with smaller channel height(about less than 2 mm) and bigger channel width (about more than 4 mm), can be attractive design for better heat removal and higher production.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.612-619
• /
• 2014

This paper proposes a real-time multi-camera video surveillance system with automatic resolution control using motion detection. In ordinary times, it acquires 4 channels of QVGA images, and it merges them into single VGA image and transmit it. When motion is detected, it automatically increases the resolution of motion-occurring channel to VGA and decreases those of 3 other channels to QQVGA, and then these images are overlaid and transmitted. Thus, it can magnifies and watches the motion-occurring channel while maintaining transmission bandwidth and monitoring all other channels. When it is synthesized with 0.18 um technology, the maximum operating frequency is 110 MHz, which can theoretically support 4 HD cameras.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.4
• /
• pp.1-7
• /
• 2013

In the next generation of mobile communication systems, high data rates and high capacity will be possible if multiple antennas are used at new frequencies. This paper presents the correlations between channel parameter path loss (PL), delay spread (DS), angular spread (AS) and K-factor established based on channel measurements. To avoid interference from Korean DTV broadcasting, we measured the channel characteristics in urban/rural/suburban areas on Jeju Island using a channel sounder and $4{\times}4$ antennas. The correlations between channel parameter show that the wireless channel characteristics can be determined and effective communication system design can be produced for use in similar environments.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.94-103
• /
• 2016

A regeneratively-cooled channel in a liquid rocket engine is used to effectively cool a combustion chamber inner wall from hot combustion gas, and the heat transfer/pressure loss characteristics should be predicted in advance to design cooling channels. In the present research, five cooling channels with different geometric dimensions were designed and the channels were respectively manufactured using cutter and endmill. By changing coolant velocity and downstream pressure, the effects of manufacturing method, channel shape, and flow condition on pressure losses were experimentally investigated and the results were compared with the analytical results. At same channel shape and flow condition, the pressure loss in the channel machined by the cutter was lower than that by the endmill. It was also found that the pressure loss ratio between the experimental result and the analytical data changed with the channel shape and flow condition.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.1
• /
• pp.1-9
• /
• 2009

This paper deals with the realization of multi-channel live karaoke. In this study, 6-channel MP3 decoding and tempo/key scaling was operated in real time by using the TMS320C6713 DSP, which is 32 bit floating-point DSP made by TI Co. The 6 channel consists of front L/R instrument, rear L/R instrument, melody, and woofer. In case of the 4 channel, rear L/R instrument can be replaced with drum L/R channel. And the final output data is generated as adjusted to a 5.1 channel speaker. The SOLA algorithm was applied for tempo scaling, and key scaling was done with interpolation and decimation in the time domain. Drum channel was excluded in key scaling by separating instruments into drums and non-drums, and in processing SOLA, high-quality tempo scaling was made possible by differentiating SOLA frame size, which was optimized for real-time process. The use of 6 channels allows the composition of various channels, and the multi-channel audio system of this study can be effectively applied at any place where live music is needed.