• 한국신뢰성학회지:신뢰성응용연구
• /
• 제11권4호
• /
• pp.343-356
• /
• 2011

This paper proposes an accelerated life evaluation of drive shaft. The life test of drive shaft for independent suspension type AWD vehicle should be performed by use of the least test sample because many number of samples can't be used for the test because of its mass capacity and high price. We calculated the no failure test time by application of no failure test concept, and the already performed test data for drive shaft are applied for some kinds of reliability coefficients which are needed for calculation of life test time. And, for analysis of real driving condition of vehicle, the load spectrum is prepared using the needed road condition and vehicle data. The inverse power model is used for accelerated life test. The equivalent torque of load spectrum is achieved by use of Miner's Rule, and then the final accelerating condition is determined by decision of the accelerated test torque. This paper shows that the accelerated life test results corresponds with the target life and the proposed life test method can be very well applied to no failure life test for mass capacity machinery components.

• 산업기술연구
• /
• 제26권B호
• /
• pp.11-20
• /
• 2006

LNG is a valuable fuel since it offers some environmental, energy security and economic benefits over diesel. It could be used mainly in heavy-duty trucks and buses. Car acceleration induces the slope angle of the liquid fuel in the tank. Slope angle changes the surface area wetted by liquid fuel and consequently heat leak to the tank. This research is a result of numerical simulation of the heat leak with the car acceleration to LNG tank. The "Pro-HeatLeak" Fortran program is developed and the verification test of the developed program is done. The difference between numerical results and calculated results from MathCad verification test is less than 0.07 percent. The smallest heat leak is correspond to the case without oscillation. For the high car acceleration the value of heat leak is greater than that for the small acceleration. The difference between maximum and minimum heat leak for 10 gallons of fuel vapor in the tank is about 10 percent.

• 한국생산제조학회지
• /
• 제24권6호
• /
• pp.653-659
• /
• 2015

The aim of this study is to develop a technique for the accelerated life test of the capacitor in a propulsion control device of a traction inverter used for a high-speed train. Using this technique, the accelerated life test can possibly estimate the life cycle of a capacitor under various temperature conditions and irregularly applied voltage. The accelerated life test is conducted for the capacitor of the traction inverter. The common proceedings of this test are selection of failure mechanism, determination of accelerated stress, range determination of the accelerated stress, determination of the test condition, and distribution and determination of the sample. From this result, the continuous applied voltage was not considered for the acceleration factors anymore. Therefore, the final result having an acceleration factor of 9.4 (= 13,626/1,445) was observed. Furthermore, the life-shortening acceleration effect for the irregular applied voltage condition can be applied to various situations.

• 한국강구조학회 논문집
• /
• 제12권4호통권47호
• /
• pp.407-416
• /
• 2000

본 연구는 실험적인 방법으로 이동하중을 받는 판형교의 동적 응답을 연구하였다. 판형교의 상부 슬래브는 판요소로, 거더는 보요소로 이상화였다. 이동하중과 판형교는 각각 소규모 차량모델과 교량모델로 제작하였다. 이동 하중을 받는 판형교의 동적 응답은 변형계, 변위계, 가속도계 및 변형도 측정기를 이용하여 측정하였고 측정한 자료로부터 얻은 최대동적응답을 유한요소법의 결과와 비교하였다. 실험적인 모형실험으로 판형교의 동적응답을 얻을 수 있음을 알 수 있다.

• Journal of Welding and Joining
• /
• 제28권1호
• /
• pp.77-85
• /
• 2010

Stainless steel sheets are widely used as the structure material for the railroad cars and the commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. Gas welding is very important and useful technology in fabrication of a railroad car and vehicles structure.However fatigue strength of the gas welded joints is considerably lower than parent metal due to stress concentration at the weld, fatigue strength evaluation of gas welded joints are very important to evaluate the reliability and durability of railroad cars and to establish a criterion of long life fatigue design. In this paper, $({\Delta}{\sigma}_a)_R-N_f$ curve were obtained by fatigue tests. Using these results, the accelerated life test(ALT) was conducted. From the experimental results, an acceleration model was derived and acceleration factors are estimated. So it is intended to obtain the useful information for the fatigue lifetime of plug and ring gas welded joints and data analysis by statistic reliability method, to save time and cost, and to develop optimum accelerated life prediction plans.

• 한국철도학회논문집
• /
• 제12권5호
• /
• pp.772-777
• /
• 2009

지구 온난화를 경감 하기위한 차세대 동력시스템으로서 연료전지 동력시스템은 승용차를 중심으로 활발하게 개발되고 있다. 가선이 설치되어있지 않은 철로에서의 철도차량의 경우에 있어서도 연료전지 동력시스템의 적용이 선진 각국을 중심으로 연구개발 되고 있다. 본 논문에서는 가속, 타행주행 및 감속을 반복하여 주행하는 경전철에 대하여 연료전지 하이브리드 동력시스템을 적용하고자 할 때 이에 대한 설계 및 제어전략을 논하였고, Matlab/Simulink로 모델링하여 시뮬레이션을 수행하였다.

• 한국지능시스템학회논문지
• /
• 제20권5호
• /
• pp.694-700
• /
• 2010

본 논문에서는 퍼지 이론을 이용한 차량용 지능형 자동 변속 알고리즘을 제안하고, 알고리즘 성능 및 최적화 분석이 가능한 시뮬레이터를 개발한다. 제안된 지능형 자동변속 알고리즘은 목표 속도 도달 시간 및 구간 가속의 성능 저하 없이 엔진 회전수 변화를 적게 하여 승차감을 개선하고, 구간 시간 내의 구동력 사용량을 줄임으로써 에너지 효율을 향상 시킨다. 또한, 모의 실험이 가능한 시뮬레이터를 개발하여 다양한 조건에서의 알고리즘 성능을 분석하고, 알고리즘 최적화 및 실용화 개발 비용 절감에 기여한다. 시뮬레이터를 이용한 모의실험을 통하여 일반 자동변속기와 제안된 자동변속기의 성능을 검증하고 시뮬레이터를 이용한 최적화 작업의 간단한 예를 보인다.

• 한국안전학회지
• /
• 제27권3호
• /
• pp.1-8
• /
• 2012

Characteristics of smoke emission in light duty diesel vehicles was investigated according to the year of production, engine displacement volume, and mileage. The smoke emission was measured using light extinction smoke measurement method under free acceleration test mode. Total number of the tested vehicles was 180. The year of production of the tested vehicles distributed from 2002 to 2007. The displacement volumes of the tested vehicles were categorized as 2-liter, 2.5-liter, 2.7-liter, and 3-liter. The mileage of the tested vehicles distributed from 20,000 km to 400,000 km. The more recent in the year of production of the tested vehicles did not show clearly lower in smoke emissions. Smoke emission showed different values according to driver's pedal pushing pattern. Also, smoke emission peak for each free acceleration test initially increased and reach a maximum of the peak values. Afterwards, the smoke peak gradually decreased as number of test increased. A new guide line was proposed to determine the smoke value from the light duty diesel vehicles based on smoke emission peak patterns which were obtained with several repeated free acceleration tests.

• 항공우주기술
• /
• 제1권1호
• /
• pp.28-41
• /
• 2002

본 논문의 목적은 실제 관성항법센서를 사용하여 개발된 스트랩다운형 관성항법시스템 및 이용 알고리즘에 대한 성능 및 오차를 평가하는 것이다. 시험은 관성항법센서의 조합을 두가지로 나누어 수행하였는데, 서로 다른 바이어스를 갖는 중급의 가속도계와 저급의 가 속도계가 사용되었으며, 자이로의 경우는 FOG(Fiber Optic Gyro)를 사용하였다(SDINS-1, SDINS-2). 관성항법시스템의 성능을 평가하기 위해서 두가지의 시험이 수행되었으며, 3축 운동 시험대를 이용한 지상정지시험과 차량을 이용한 단거리 주행시험을 수행하였다. 단거 리 주행시험의 결과는 정확도 20 mm를 갖는 DGPS(Differential GPS)의 시험결과와 비교 하였으며, 결과 및 오차를 나타내었다.

• 한국기계가공학회지
• /
• 제19권11호
• /
• pp.49-57
• /
• 2020

The forced vibration characteristics for two impulse forces with time lag was discussed in the vehicle dull progress model. Detailed numerical analyses of the time domain were performed systematically. By the two exciting impulse forces, the responses of displacement, the velocity, and the acceleration were investigated in detail for the vehicle's vibration. Notably, the forced vibration responses in the time domain can be used to identify and monitor several vehicle vibration models. In order to define the responses of displacement, the velocity, and the acceleration, we applied a numerical technique (i.e., the Runge-Kutta-Gill method[1,2]). These variables were subsequently used to analyze the vehicle's vibration according to the time lapse and while it passed over a bump stock; moreover, the characteristics of the variables were analyzed in detail according to their force conditions. Finally, the intrinsic characteristics of the forced vibration were discussed in the context of the automobile model. Overall, our results indicate that the tested method can be successfully applied under different damped conditions.