• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.726-732
• /
• 2019

In this study, we proposed an asymmetric differential inductor to improve the linearity of differential power amplifiers. Considering the phase error between differential signals of the differential amplifier, the location of the center tap of the differential inductor was modified to minimize the error. As a result, the center tap was positioned asymmetrically inside the differential inductor. With the asymmetric differential inductor, the AM-to-AM and AM-to-PM distortions of the amplifier were suppressed. To confirm the feasibility of the inductor, we designed a 2.4 GHz differential CMOS PA for IEEE 802.11n WLAN applications with a 64-quadrature amplitude modulation (QAM), 9.6 dB peak-to-average power ratio (PAPR), and a bandwidth of 20 MHz. The designed power amplifier was fabricated using the 180-nm RF CMOS process. The measured maximum linear output power was 17 dBm, whereas EVM was 5%.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.440-447
• /
• 2002

This paper considerated about exact flow volume calculation method from factors having an influence on measurement and introduced in anesthesia ventilator realized spirometry system. System used differential pressure sensing method with factors, that is temperature, pressure, gas density, humidity and mucus etc. System optimized for low power system for mobile system. System composed analog interface part, signal processing part, display part. Analog interface part have differential pressure flow sensor and defferential pressure sensor. Signal processing part have AVR processor for low power system display part use serial port (RS232, SPT). so it display at pc monitor or send to anesthesia ventilator. System is stable by linearizing 2th characteristics of flow-differential pressure, auto correction of sensor. Noise reduced by algorithm with analog filter and digital processing. Small, light, low power system is good at mobile system and applied to patient in emergency or mobile. and, System is useful at anesthesia ventilator by using flow sensor.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.205-215
• /
• 2001

Continuously variable transmission(CVT) mechanisms considered here combine the functions of a 2K-H I type differential gear unit and a V-belt continuously variable unit(CVU). One shaft of the V-belt CVU is connected directly to the differential gear unit and remaining shaft of it is linked to the output shaft. These mechanisms have many advantage which are the decrease of CVT size, the increase of overall efficiency, the extension of speed ratio range, and the generation of geared neutral. In this paper six different mechanisms of output coupled type CVT are proposed. Some useful theoretical formula related to speed ratio, power flow and efficiency are derived and analyzed, and theoretical analysis are proven by various experiments.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.21-22
• /
• 2016

본 논문에서는 차동전력조절방식을 추가하여 최대 전력점을 추종하는 동시에 출력단에 직렬로 연결된 부하가 전하 균등화 기능을 수행하는 회로를 제안한다. 제안하는 회로는 각각의 PV모듈을 제어를 하고, 이를 상태공간평균화기법을 이용하여 해석하였다. 본 논문에서의 전력조절기는 포워드컨버터로 구성 되어 있고, 주 컨버터인 전하균등화회로는 벅-플라이백컨버터로 구성하였다. 컨버터의 입력은 PV모듈을 직렬로 연결, 출력은 배터리를 직렬로 연결하여 제안한 기능을 구현하였다. 이에 따른 조건을 수식으로 증명하고, MATLAB과 모의 시뮬레이션 프로그램인 PSIM의 Bode plot을 비교하여 이를 검증하였다.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.3
• /
• pp.1-7
• /
• 2014

This paper describes the implementation of high speed comparator for the ATE (automatic test equipment) system. The comparator block is composed of continuous comparator, differential difference amplifier(DDA) and output stage. For the wide input dynamic range of 0V to 5V, and for the high speed operation (1~800MHz), high speed rail-to-rail amplifier is used in the first stage. And hysteresis circuits, pre-amp and latch are followed for high speed operation. To measure the difference of output signals between the two devices under test (DUTs), a DDA is applied because it can detect the differences of both common signals and differential signals. This comparator chip was implemented with $0.18{\mu}m$ BCDMOS process and can compare the signal difference of 5mV up to the frequency range of 800 MHz. The chip area of the comparator is $620{\mu}m{\times}830{\mu}m$.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.38 no.4
• /
• pp.20-30
• /
• 2001

A novel 200 MHz CMOS transconductor using translinear cells is proposed. The proposed transconductor consists of voltage followers and current followers based on translinear cells and a resistor. For wide applications, a single-input single-output, a single-Input differential-output, and a fully-differential transconductor are systematically designed, respectively. The theory of operation is described and computer simulation results are used to verify theoretical predictions. The results show that the fully-differential transconductor has a linear input voltage range of ${\pm}2.7$ V, a 3 dB frequency of 200 MHz, and a temperature coefficient of less than 41 $ppm/^{\circ}C$ at supply voltages of ${\pm}3$ V. In order to certify the applicability of the fully-differential transconductor, A ladder-type 3th-order cllitic low pass filter is also designed based on the inductance simulation method. The filter has a ripple bandwidth of 22 MHz, a pass-band ripple of 0.36 dB, and a cutoff frequency of 26 MHz.

• The Journal of the Korea Contents Association
• /
• v.6 no.3
• /
• pp.38-45
• /
• 2006

A dual-level low voltage differential signalling (DLVDS) circuit is proposed aiming at reducing transmission lines for a LCD driver IC. We apply two data to the proposed DLVDS circuit as inputs. Then, the transmitter converts two inputs to two kinds of fully differential signals. In this circuit, two transmission lines are sufficient to transfer two inputs while keeping the LVDS feature. However, the circuit has a common mode bias fluctuation due to difference of the input bias and the reference bias. We compensate the common mode bias fluctuation using a feedback circuit of the current source bias. The receiver recovers the original input data through a level decoding circuit. We fabricated the proposed circuit using $0.25{\mu}m$ CMOS technology. The simulation results of proposed circuit shows 1-Gbps/2-line data rate and 35mW power consumption at 2.5V supply voltage, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.4
• /
• pp.891-896
• /
• 2011

This paper describes the differential voltage-to-frequency converter which is realized current conveyor circuits. The output frequency of the differential voltage-to-frequency converter is proportional to the difference of two input voltages. The designed circuit is simulated by HSPICE. The range of input voltage difference is from several volts to several milli-volts. From the simulation results the error is less than from -1.9% to +1.8% compared to the calculated values.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.228-233
• /
• 2000

In this paper, we introduce a differential detection method using approximate average noise detection, which improves the noise reduction efficiency in a wireless optical interconnection. Approximate average noise detection reduces the output voltage fluctuation that may result from the instantaneous change of the coupling coefficients with the movement of some objects or human beings. This method is very useful for noise reduction in an environment with optical noise whose spatial distribution varies instantaneously.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.5
• /
• pp.822-829
• /
• 2000

In this paper, we introduce a differential detector that automatically aligns itself to the signal beam in order to prevent the voltage variation that may result from minute misalignment of the light source. In this system, a photodiode-array recognizes the central point of the signal beam, and drives motors that correspond to the x and y axes. The photodiode-array aligns itself to the central point of the signal beam, and eliminates the optical noise effect with differential detectioin method. It is very useful in wireless optical interconnections.