• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.658-664
• /
• 2012

This paper presents an investigation into driveline clonk noise of midi-bus. Test was performed for operational acceleration and pressure, torsional vibration of driveline and FRF to TPA. Wavelet analysis was used to study spectral-time characteristics to all measurement data and specially for torsional vibration, lash analysis was carried out. To investigate the path of the clonk in detail, time domain TPA was introduced. With time domain TPA, the contribution of each path for the clonk was estimated by both subjectively and objectively. As a result, Transmission mount part was came to light as the main contributor of issued clonk. This was verified by reinforcing the bracket of transmission side. And 1D torsional nvh performance simulation model was built with measured torsional vibration. The simulation tool was used for prediction of some clonk behavior in tip in-out transient condition.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.121-127
• /
• 2012

Whine noise in engine oil pump system was issued in developing an engine. Generally, A noise of engine oil pump largely are classified two cases. The first one is a gearing noise caused by relative motion of inner rotor and outer rotor. The other is fluid pulsation noise caused by oil pressure fluctuation. The aim of the paper is to identify a noise mechanism in engine oil pump and improve its Noise. Also, it suggests to the guide line on the design of oil pump.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 춘계학술대회 논문집
• /
• pp.425-426
• /
• 2010

Recently, Most of diverse noise of vehicles has decreased competitively according to development of the automotive manufacturing technology. Especially, Passenger car manufacturers has been conducting buzz, squeak and rattle(BSR) noise test as a method of the noise evaluation tests to reduce an unpleasant sound from interior parts on the driving the car. This paper suggest a evaluation method for detecting position of noise source from measured noise signals of vehicle seats during random excitation BSR test. Hereby the BSR test procedure used the test regulation of 'G' company. The detection of noise source positions used the Sound image equipment. Through suggested the test method on this paper, an accurate analysis of noise source occurred in the BSR test will be possible.

• 한국소음진동공학회논문집
• /
• 제18권7호
• /
• pp.756-763
• /
• 2008

This paper presents an inchworm with three piezoelectric actuators. The dynamic stiffness of the inchworm is generally low compared to its driving condition, so mechanical vibration may degenerate the motion accuracy of the inchworm. The dynamic model of inchworm is identified by curve fitting technique based on the experimental frequency response function. For the precision motion control and low residual vibration of inchworm, driving input signal is designed by using cycloid step input and LQG control technique. Experimental result shows that proposed input shaping method is applicable effectively to the inchworm.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1268-1273
• /
• 2003

This paper presents a case history of piping failures on power plant. The root cause of the failure was defined to set the optimal countermeasures. The failure comes from transient vibration and the 1st stress increased at the hydraulic oil supply system of control valves for high pressure steam turbine.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.498-503
• /
• 2003

Dynamic analysis of a plate with non-linearity due to large deformation is performed in the study. There have been many researches about the non-linear dynamic behavior of plates examining by means of theoretical or numerical analyses. But it is important how exactly model the actual system. In this respect, the Continuous-Time system identification technique is used to generate non-linear models, for stiffness and damping terms, to explain the observed behaviors with single mode assumptions for the simplicity after comparing the experimental results with the numerical results of a linear plate model.

• 한국소음진동공학회논문집
• /
• 제14권10호
• /
• pp.930-938
• /
• 2004

This paper presents the noise source identification of a car A/V system. There are two different kinds of noise sources noise generated by loading mechanism and rattle noise by externally forced vibration. A dynamometer has been made to produce stationary inertia to the loading mechanism of A/V system. Sound pressure spectra and sound intensity were measured by operating the dynamometer setup as various motor speeds, and the results were analyzed. A dominant rattle noise source about A/V system's components has been found by multi-dimensional spectral analysis. Residual spectrum method was applied for eliminating coherence between the vibration sources. In result, the dominant rattle noise source was identified by partial coherent output spectrum of individual vibration component.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.463-468
• /
• 2011

According to a quantum leap of the performances of automobile, environmental factors are important as functional factors, especially noise. BLDC motor, one of the part of automobile, is also no exception. In this paper, investigation of the sound sources of outer rotor type BLDC motor is performed. In order to reduce noise, it must be necessary knowing sound source. To this end, this paper is analyzed two viewpoints, structural and electromagnetic causes. For structural analysis, modal experiment and 3D mode analysis are performed. On behalf of electromagnetic analysis, 2D finite element method is carried out. Finally, coupling analysis is performed in order to know about influence between two factors.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.324-329
• /
• 2003

An air-conditioner has various noise sources such as cooling fan noise, pumping noise, flow noise and impact noise. Among these, impact noise is the most unpleasant source. This is because the noise is produced in indoor unit of air-conditioner. To control the noise source effectively, first we must identify the noise sources. When we identify impact noise source, the measurement have to be carried out simultaneously. So we use beamforming method that requires less measurement points than intensity method and acoustic holography. The objective of this paper is to estimate the location of impact source. This objective can be achieved by using minimum variance cepstrum that is able to detect impulse embedded in noise. In this study, modified beamforming method based on cepstrum domain is proposed. Then this method applied to air-conditioner noise sources which produce impact noise.