• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.7
• /
• pp.493-502
• /
• 2001

This paper propose a new built-in current sensor(BICS) for current testing that has some advantages compared with conventional logic testing. The designed BICS detects the fault in circuit under test (CUT) and makes a Pass/Fail signal by comparison between CUT current and duplicated inverter current. The proposed circuit consists of a differential amplifier, a comparator and a inverter. It requires 10 MOSFETs and 3 inverters. Since the designed BICS do not require the extra clock, the added extra pin is only one output pin. The mode selection is not used in this circuit. Therefore we can apply the circuit to on-line testing. The validity and effectiveness are verified through the HSPICE simulation of circuits with defects. When CUT is a 8$\times$8 parallel multiplier, area overhead of the BICS is about 4.34%.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.227-228
• /
• 2006

In this paper, we introduce the design and fabrication of 60 GHz low noise amplifier MMIC for IEEE802.15.3c WPAN system. The 60 GHz LNA was designed using ETRI's $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The performances of the fabricated 60 GHz LNA MMIC are operating frequency of $60.5{\sim}62.0\;GHz$, small signal gain ($S_{21}$) of $17.4{\sim}18.1\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-14{\sim}-3\;dB$, output reflection coefficient ($S_{22}$) of $-11{\sim}-5\;dB$ and noise figure (NF) of 4.5 dB at 60.75 GHz. The chip size of the amplifier MMIC was $3.8{\times}1.4\;mm^2$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.7
• /
• pp.12-22
• /
• 2012

The main drawback of the multi-code spread spectrum communication system, which spreads data bits stream by the multiplexed orthogonal codes, is the need for the highly linear amplifier. Several constant amplitude precoding schemes have been proposed for the Walsh code or the extended $m$-sequence based multi-code spread spectrum systems. In the constant amplitude spread spectrum systems the accompany code is transmitted together with orthogonal codes to maintain the transmitter output in a constant level. In this paper we propose the use of the accompany in the receiver to improve the BER performance. The proposed receiver has the capability to correct the code detection error(up to one code error). We carried out simulations to verify the validity of the proposed algorithm. BER performance improvement was noticed compared with the conventional receiver.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.12
• /
• pp.66-71
• /
• 2014

This paper presents an analog front-end integrated circuit (IC) for medical ultrasound imaging systems using standard $0.18-{\mu}m$ CMOS process. The proposed front-end circuit includes the transmit part which consists of 15-V high-voltage pulser operating at 2.6 MHz, and the receive part which consists of switch and a low-power low-noise preamplifier. Depending on the operation mode, the output driver in the transmit pulser can be reconfigured as the switch in the receive path and thus the area of the overall front-end IC is reduced by over 70% in comparison to previous work. The designed single-channel front-end prototype consumes less than $0.045mm^2$ of core area and can be utilized as a key building block in highly-integrated multi-array ultrasound medical imaging systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.551-561
• /
• 2001

In this paper, the large signal unified model is established for H4O GaAs pHEMT of GEC-Marconi using modified Curtice model. This unified model includes DC characteristic, small signal, and noise characteristic as various bias. Particularly, the model can simply and physically explain trans-conductance $(g_m)$ of pHEMT using modified Curtice model, and can tell the difference $g_m$, $R_ds$ at DC and these at AC through inclusion of internal RF-choke. The results of the established model built up using SDD in HP-Eessof show good agreement to the S/W measured data in DC, small signal, and noise characteristic. This model can also be applied to various computer aided analysis, such as linear simulation, 1-tone harmonic balance simulation, and multi-tone harmonic balance simulation, so the LNA(Low Noise Amplifier), oscillator, and mixer design has been shown using this model library.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.576-585
• /
• 2001

In this paper, we investigated the method of compensation for optical pulse shape distortion due to both chromatic dispersion and SPM(self phase modulation) in a single mode fiber We selected MSSI(mid-span spectral inversion) as compensation method using OPC(optical phase conjugator). We used EOP(eye-opening penalty) parameter in order to evaluate the efficiency of waveform distortion compensation. In this paper, we induced optimum pump power level in optical phase conjugator through analytic method of computer simulation. And we investigated input signal power range being able to maintain stable reception performance under the condition of optimum pump power. We verified the possibility of high performance optical transmission system realization through the inducement and application of optimum pump power, input signal power and in-line amplifier spacing, because power control is important in the compensation for optical pulse distortion.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.84-92
• /
• 2000

A GaAs MESFET MMIC transmitter for 2.4 GHz wireless local loop handset is designed and fabricated. The transmitter consists of a double balanced active mixer and a two stage driver amplifier with voltage negative feedback. In particular, a pair of CS-CG(common source-common gate) structure compensates the reduction in dynamic range caused by unbalanced complementary IF input signals. And to suppress the leakage local power at RF port, the mixer is designed by using phase characteristic between the ports of MESFET. At the bias condition of 2.7 V and 55.2 mA, the fabricated MMIC transmitter with chip dimensions of $0.75\times1.75 mm^2$ obtains a measured conversion gain of 38.6 dB, output $P_{idB}$ of 11.6 dBm, and IMD3 at -5 dBm RF output power of -31.3 dBc. This transmitter is well suited for WLL handset.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.115-122
• /
• 2016

In this paper, wideband Ku-band downconverter was designed to receiver digital satellite broadcasting. The low-nose downconverter was designed to form four local oscillator frequencies(9.75, 10, 10.75 and 11.3 GHz) representing a low phase noise due to VCO-PLL with respect to input signals of 10.7 to 12.75 GHz and 3-stage low noise amplifier circuit by broadband noise matching, and to select intermediate frequency bands by digital control. The developed low-noise downconverter exhibited the full conversion gain of 64 dB, and the noise figure of low-noise amplifier was 0.7 dB, the P1dB of output signal 15 dBm, and the phase noise -85 dBc@10kHz at the band 1 carrier frequency of 9.75 GHz. The low noise block downconverter(LNB) for wideband digital satellite broadcasting designed in this paper can be used for global satellite broadcasting LNB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.11
• /
• pp.1315-1322
• /
• 2012

Frequency domain reflectometry diagnoses faults on electric cables by measuring the cable impedance. Time domain impedance measurement technique using an oscilloscope instead of a network analyzer is widely used for electric power cables under harsh environment or powered condition. However, impedance measurement in the time domain shows inaccuracy as the frequency increases due to several parasitic impedances, which results in the poor resolution of fault points. This paper presents the accuracy enhancement technique using a module with an operational amplifier and an error calibration method in the time domain impedance measurements, which is confirmed by comparing the cable impedance measurement results.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.623-624
• /
• 2006

In this paper, we introduce the design and fabrication of V-band power amplifier MMIC with excellent gain-flatness for IEEE 802.15.3c WPAN system. The V-band power amplifier was designed using ETRI' $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The gains of the each stages of the amplifier were modified to have broadband characteristics of input/output matching for first and fourth stages and get more gains of edge regions of operating frequency range for second and third stages in order to make the gain-flatness of the amplifier excellently for wide band. The performances of the fabricated 60 GHz power amplifier MMIC are operating frequency of $56.25{\sim}62.25\;GHz$, bandwidth of 6 GHz, small signal gain ($S_{21}$) of $16.5{\sim}17.2\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-16{\sim}-9\;dB$, output reflection coefficient ($S_{22}$) of $-16{\sim}-4\;dB$ and output power ($P_{out}$) of 13 dBm. The chip size of the amplifier MMIC was $3.7{\times}1.4mm^2$.