• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.3
• /
• pp.253-255
• /
• 2001

기능성고분자재료 중의 하나인 7원환 고리아세탈 화합물인 1,3-dioxepan-2-one(1)을 합성하고 고온조건 하에서 중합반응을 조사한 결과 선택적인 개환중합이 일어났다. 그러나 낮은 농도에서 작은 분자량을 가지는 고분자가 얻어졌으며 넓은 분자량 분포와 낮은 수율이 얻어지며 이것은 중압반응 도중에 분자 내에서 상호반응을 일으킴을 보여준다.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.1
• /
• pp.57-63
• /
• 2019

This study aimed to determine whether the curing times of Xtra Power and High Power modes of high-power light emitting diode (LED) curing light are sufficient for polymerization of resin sealants. The specimens were prepared and their microhardness values were measured and compared with those of specimens polymerized under conventional LED curing light. The filled sealant polymerized for 8 seconds in the High Power mode and for 3 seconds in the Xtra Power mode showed significantly lower microhardness than the control specimen (p = 0.000). The unfilled sealant polymerized for 8, 12 seconds in the High Power mode and for 6 seconds in the Xtra Power mode showed significantly lower microhardness than the control specimen (p = 0.000). The results of this study suggest that the short curing time with the Xtra Power and High Power modes of highpower LED curing light are not sufficient for adequate polymerization of sealants under specific conditions, taking into account the curing times and the type of sealant.

• Polymer(Korea)
• /
• v.24 no.4
• /
• pp.437-444
• /
• 2000

Propylene polymerizations were carried out by using rac-Et(Ind)$_2$ZrCl$_2$ (Zirconocene catalyst) and a commercial third generation Ziegler-Natta catalyst in a semibatch reactor. From the polymerization reactions, the optimum reaction conditions and the physical properties of polymers produced from each catalyst system were investigated. The optimum reaction temperatures of rac-Et(Ind)$_2$ZrCl$_2$ and Ziegler-Natta catalyst were 5$0^{\circ}C$, 4$0^{\circ}C$, respectively. On the basis of the results for the produced polymer particle size distributions and the catalytic activities of polymerization reaction, the reaction temperature should be considered as an important factor for the successful polymerization reactions. Especially, the polymer was conglomerated in the higher reaction temperature. It was found that there was an upper limitation to co-catalyst concentration. Reaction rates and polymer yields rather decreased with increasing the concentration of to-catalyst, i.e., MAO and TEAl affected only polymerization activities, but the PEEB in Ziegler-Natta catalyst system affected isotactic indexes of produced polymer as well as activities. Based on these observations, the production yield seems to exhibit a first order lineal relationship to the partial pressure of monomer.

• Journal of Adhesion and Interface
• /
• v.10 no.4
• /
• pp.174-181
• /
• 2009

The viscosity for hi-solid pressure sensitive adhesive to improve water soluble low viscosity pressure sensitive adhesive polymerized using seeded polymerization. While seed binder polymerizing it produces an optimum polymerization condition, and acrylic acid and seed binder concentration changed were measurement of viscosity variation and adhesive power at the substrate (SUS420J) as flowing results. In adhesive polymerization, seed binder concentration 7 wt%/monomer was recovered 60% of solid content, 2,100 cps of low viscosity and clear adhesive film. When acrylic acid content was 4 wt%/monomer, it was turned excellent adhesive power and holding power.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.698-705
• /
• 2016

In this study, we have studied the polymerization of polyethylene wax using metallocene catalysts and its physical properties. Various polymerization conditions were tried for polymerization of polyethylene wax. We have evaluated hydrogen reactivity and studied on characteristics of polymerization effected by ligand structure of metallocene catalysts against Ziegler-Natta catalysts which are widely used for polymerization of polyethylene. We have also checked hydrogen used for chain transfer agent, molecular weight change and distribution by different ratios of ethylene gas. Finally, we suggest proper structure of metallocene catalysts for polymerization of polyethylene wax.

• Polymer(Korea)
• /
• v.32 no.4
• /
• pp.385-389
• /
• 2008

Chain propagation and chain transfer in anionic polymerization of hexafluoropropylene oxide were investigated under various reaction conditions such as the stabilization of reaction temperature, the amount of hexafluoropropylene solvent, and the feeding rate of hexafluoropropylene oxide monomer. Anionic initiator for the polymerization was synthesized from cesium fluoride and hexafluoropropylene oxide in tetraethyleneglycol dimethylether. It was possible to obtain a high molecular weight poly(HFPO) ($M_w$ 14800) using the anionic initiator in conditions of stabilized reaction temperature, and optimized addition of solvent and monomer feeding (HFP/initiator mole ratio=31.5 and HFPO feeding rate=11.67 g/hr). Otherwise, chain transfer reaction in anionic polymerization was increased. From the results of molecular weight in various reaction conditions, it was found that chain propagation and chain transfer in anionic polymerization of HFPO were very sensitive to reaction conditions.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.263-268
• /
• 2013

In this study, we prepared poly(ethylene-ter-1-hexene-ter-divinylbenzene) using bridged rac-$Et[Ind]_2ZrCl_2$ metallocene catalysts. The effect of 1-hexene on the terpolymerization rate was evaluated. When cocatalyst/catalyst molar ratio was 3,000, catalytic activity indicated more than 8,000 which was very remarkable value. As polymerization time increased, the weight-average molecular weight of the terpolymer gradually increased to some degree. In case of a polymerization time of 50 minutes, the terpolymer became amorphous state. The molecular weight distribution and densities of the terpolymer were 110,000-200,000 and $0.85-0.89g/cm^3$, respectively. Thermal properties and structure of the terpolymer were also identified.

• Elastomers and Composites
• /
• v.48 no.1
• /
• pp.2-9
• /
• 2013

We synthesized polyethylene, poly(ethylene-co-1-decene), poly(ethylene-co-p-methylstyrene), and poly(ethylene-ter-1-decene-ter-p-methystyrene) using a rac-$Et(Ind)_2ZrCl_2$ metallocene catalyst and a methylaluminoxane cocatalyst system. The materials were characterized using nuclear magnetic spectroscopy and fourier transform infrared spectroscopy. To identify suitable reaction conditions for terpolymerization, we studied the effects of catalyst content, cocatalyst/catalyst molar ratio, polymerization time, and polymerization temperature. As the catalyst content increased, the catalytic activity and the molecular weight of the terpolymers increased. The catalytic activity sharply increased but little change was observed after a polymerization time of 30 min. The increase in the cocatalyst/catalyst molar ratio resulted in a decrease in the molecular weight of the terpolymers and an increase in the catalytic activity to some degree. The catalytic activity increased with increasing polymerization temperature, while the molecular weight of the terpolymers decreased.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.609-614
• /
• 2010

In this study, emulsion polymerizations for synthesizing acrylic pressure-sensitive adhesive(PSA) were carried out using 2-ethylhexyl acrylate(2-EHA), n-butyl acrylate(n-BA), methyl metacrylate(MMA) as fundamental monomers and acrylic acid(AAc) as a functional monomer in the presence of anionic SLS (sodium lauryl sulfate). To obtain the optimized synthetic condition in the polymerization, we analyzed the polymerization variables such as the effect of surfactant concentration and hydrophilic lipophilic values(HLB). At the same time, the final adhesive properties were also analyzed by the function of the initiator concentration and buffer concentration. In the results, the most stable emulsion was obtained at the surfactant concentrations between 3 and 5 wt%. It was also determined the effect of HLB value of nonionic surfactant and the initiator concentrations on the gel content. Stable emulsion is obtained using the surfactant having HLB value of 12.3. The rate of emulsion polymerization was increased at the initiator concentration greater than 1 wt%, but the stability of the emulsion was decreased. Finally, the effect of the buffer concentrations on the pH and the conversion of the acrylic emulsion product were experimentally measured. At the sodium bicarbonate concentration above 0.4 wt%, the buffer infulence was apparent. The buffer effect was fully acceptable at the concentrations between 0.6 and 0.8 wt% regardless of the monomer composition.

• Journal of Adhesion and Interface
• /
• v.15 no.3
• /
• pp.93-99
• /
• 2014

Monodisperse poly[styrene-co-(COPS-I)] latices in the size range of 165~550nm were successfully prepared by soap-free emulsion polymerization with various polymerization conditions (Styrene, COPS-I, KPS, DVB concentrations and polymerization temperature). In general, the COPS-I and KPS, DVB concentrations and polymerization temperature were closely related to the polymerization rate and the number of particles, molecular weight, and zeta potential. The polymerization rate and zeta potential increased, but molecular weight decreased, with increasing in the number of particles.