• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.55-64
• /
• 2006

This work proposes a calibration-free 14b 70MS/s 0.13um CMOS ADC for high-performance integrated systems such as WLAN and high-definition video systems simultaneously requiring high resolution, low power, and small size at high speed. The proposed ADC employs signal insensitive 3-D fully symmetric layout techniques in two MDACs for high matching accuracy without any calibration. A three-stage pipeline architecture minimizes power consumption and chip area at the target resolution and sampling rate. The input SHA with a controlled trans-conductance ratio of two amplifier stages simultaneously achieves high gain and high phase margin with gate-bootstrapped sampling switches for 14b input accuracy at the Nyquist frequency. A back-end sub-ranging flash ADC with open-loop offset cancellation and interpolation achieves 6b accuracy at 70MS/s. Low-noise current and voltage references are employed on chip with optional off-chip reference voltages. The prototype ADC implemented in a 0.13um CMOS is based on a 0.35um minimum channel length for 2.5V applications. The measured DNL and INL are within 0.65LSB and l.80LSB, respectively. The prototype ADC shows maximum SNDR and SFDR of 66dB and 81dB and a power consumption of 235mW at 70MS/s. The active die area is $3.3mm^2$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.891-893
• /
• 2012

Currently, aircraft and automobile simulator for training provides a variety of training by making hypothetical situation on a simulator Installed on the ground Currently. And the instructor maximizes the effectiveness of the training by Monitoring training and instructing the required training. When trainees are boarding the aircraft or automobile. The Instructor in the ground is not able to monitoring aircraft, automobile. The assessment of the training is not easy after the end of the training Therefore, it is difficult to provide high quality of education to the students. In this paper, Simulation software is to develop the following. Collecting GPS and real-time information for aircraft, automobile ${\grave{a}}implementing$ 3D simulation. Implementing Current image of the aircraft or automobile in the screen by 3D Real-time monitoring of training situation at the control center utilizing for training saving 3D video files Analysis, evaluation on training After the end of the training.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.411-418
• /
• 2009

So far the Limit Equilibrium Method has been widely used by way of 2-D slope stability analysis for the evaluation of land slides and slope failures. However recently the evaluation of 3-D slope stability analysis has been comparatively possible owing to the developments of obtaining the terrain data and geological data and of 3-D slope stability analysis softwares. In Japan the evaluation of the 3-D slope stability analysis has been necessary for the stability analysis of the tunnel mouth. In this study we inspected the economic effects introducing the 3-D slope stability analysis for larger scale landslides and slope failures. In case of 3-D slope stability analysis of landslides we acquired the results that we reduce the cost of the countermeasure work of pile work by 40% comparing the 2-D slope stability analysis. Moreover in case of the stability analysis of slope failures we figured out the results that we reduce the cost of the countermeasure work of anchor works by 20%. Furthermore we proved that 3-D slope stability analysis is effective for the stability analysis of tunnel mouths around the sides of landslides and large scale embankment which we could have not evaluated by conventional 2-D section stability analysis.

• Geophysics and Geophysical Exploration
• /
• v.20 no.1
• /
• pp.25-32
• /
• 2017

We present a 3D SH-wave velocity model of the crust and uppermost mantle and seismic radial anisotropy beneath East Asia. The SH-wave velocity structure model was built using Love-wave group-velocity dispersion data from earthquake data recorded at broadband seismic networks of Korea, Japan, and China. Love-wave group-velocity dispersion curves were obtained by using the multiple filtering technique in the period range of 3 to 150 s for 3,369 event-station pairs. The inverted model using these data sets provides a crust and upper mantle SH-wave velocity structure down to 100 km depth. At 10 ~ 40 km depths SH-wave velocity beneath the East Sea is higher than beneath the Japanese island region. We estimated the Moho beneath the East Sea to be between 10 ~ 20 km depth, while Moho beneath the Korean Peninsula at around 35 km based on the depth where high-velocity anomalies are detected. We estimated the lithosphere-asthenosphere boundary beneath the East Sea to be at around 50 km based on the depth where strong low-velocity anomalies are observed. Widespread low-velocity anomalies are found between 50 ~ 100 km depth in the study region. Positive radial anisotropy ($V_{SV}$ > $V _{SH}$) is observed down to 35 km depth, while negative radial anisotropy ($V_{SV}$ > $V _{SH}$) is observed for deeper depth.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.1262-1270
• /
• 2006

사실적인 물 애니메이션을 위한 격자 기반 시뮬레이션 기법은 자연스러운 물의 움직임뿐만 아니라 부드러운 물의 표면을 잘 표현해주는 장점이 있다. 이러한 격자 기반 방법과 함께 상대적으로 적은 계산으로 안정적인 결과를 산출해주는 입자 기반의 액체 시뮬레이션 기법이 최근 애니메이션 분야에 적용되기 시작했고, 그로 인하여 입자로 이루어진 시뮬레이션 데이터에 특화된 효과적인 렌더링 기술의 개발이 요구되고 있다. 본 논문에서는 주로 3차원 스캔 데이터와 같이 물체 표면을 샘플링 하여 얻어진 점 집합에 대한 렌더링 기법을 확장하여, 위상 변화가 크고 점 집합에 의해 내부까지 표현되는 물 데이터의 특성에 적합한 렌더링 기법을 제안한다. 본 기법에서는 시뮬레이션을 통하여 얻은 입자 데이터로부터 물의 표면을 표현해주는 새로운 점 집합을 생성하고, 시뮬레이션 된 데이터의 특성을 잘 반영하도록 각 점에 대한 법선 벡터와 반지름을 결정한다. 특히 가공된 점 집합 데이터에 대하여 확장된 점 집합 렌더링 기법을 적용함으로써 입자 데이터가 표현해주는 세밀한 부분들을 보존하면서, 부드러운 물의 표면을 가시화할 수 있도록 하였다.

• Composites Research
• /
• v.14 no.1
• /
• pp.8-14
• /
• 2001

A simplified method for determining the three mode(I, II, III) components of the strain energy release rate of free-edge delaminations in composite laminates is proposed. The interlaminar stresses are evaluated using the interface moment and the interface shear forces which are obtained from the equilibrium equations at the interface between the adjacent layers. Deformation of an edge-delaminated laminate is analysed by using a generalized quasi-three dimensional classical laminated plate theory. The analysis provides closed-form expression for the three components of the strain energy release rate. The analyses are performed for composite laminates subjected to uniaxial tension, with free-edge delaminations located symmetrically and asymmetrically with respect to the laminate midplane. The analysis results agreed with a finite element solution using the virtual crack closure technique.

• Tribology and Lubricants
• /
• v.36 no.4
• /
• pp.232-243
• /
• 2020

It is essential to predict the amount of wear and surface parameters for a surface where relative motion occurs. In the asperity-based model for wear prediction, only the average contact pressure can be obtained. Hence, the accuracy of wear analysis is poor. In this study, DC-FFT is used to obtain the pressure of each node, and wear analysis is performed by considering the effect of the pressure gradient. The numerical surface generation method is used to create Gaussian, negatively skewed, and positively skewed surfaces for wear analysis. The spatial and height distributions of each surface are analyzed to confirm the effectiveness of the generated surface. Furthermore, wear analysis is performed using DC-FFT and Archard's wear formula. After analysis, it is confirmed that all peaks are removed and only valleys remain on the surface. The RMS roughness and Sk continue to decrease and Ku increases as the cycle progresses. It is observed that the surface parameters are significantly affected by the radius of curvature of the asperity. This analysis method is more accurate than the existing average wear and truncation models because the change in asperity shape during the wear process is reflected in detail.

• Korean Journal of Optics and Photonics
• /
• v.18 no.5
• /
• pp.303-308
• /
• 2007

We report here on the application of a digital holographic microscope as a metrology tool for the inspection and the micro-topography reconstruction of different micro-structures of phase shift photo-mask (PSM). The lithography by phase shift photo-mask uses the interference and the pattern of the PSM is not imaged by general optical microscope. The technique allows us to obtain digitally a high-fidelity surface topography description of the phase shift photo-mask with only one hologram image acquisition, allowing us to have relatively simple and compact set-ups able to give quantitative information of PSM.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.50-50
• /
• 2010

최근 토요타 자동차의 대량 리콜 사태로 안전과 관련된 자동차 품질에 대한 관심과 중요성이 크게 부각되었다. 본 연구에서는 나날이 높아지고 있는 자동차 품질 기준과 생산 비용 절감, 공정 자동화 요구에 부응하기 위한 차체 저항 점 용접부 품질 검사 자동화 기술 개발을 위해 적용 가능한 센서들을 비교, 검토하였다. 알려진 비파괴 검사 방법은 초음파, 와전류, 방사선 검사법 등 다양한 방법들이 존재하지만, 이 연구에서는 생산 라인 현장 적용이 가능한 소형 센서들을 중심으로 검토 영역을 제한하였다. 검토된 비파괴 검사 방법은 총 5가지 종류로 종래의 수동 초음파 검사법, 집적된 탐촉자를 이용한 3차원 초음파 검사법, NAUT(Non-contact Air-coupled Ultrasonic Test), EMAT(EletroMagnetic Acoustic Test), 그리고 너겟 프로파일러$^{TM}$이다. 이 연구에서는 각 검사법의 원리와 장단점을 설명하고 생산 라인 적용에 필요한 필수 항목들에 대해 고찰하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.201-201
• /
• 2010

DRAM (dynamic random access memory)은 하나의 트랜지스터와 하나의 캐패시터의 구조 (1T/1C)를 가지는 구조로써 빠른 동작 속도와 고집적에 용이하다. 하지만 고집적화를 위해서는 최소한의 캐패시터 용량 (30 fF/cell)을 충족시켜 주어야 한다. 이에 따라 캐패시터는 stack 혹은 deep trench 구조로 제작되어야 한다. 위와 같은 구조로 소자를 구현할 시 제작공정이 복잡해지고 캐패시터의 집적화에도 한계가 있다. 이러한 문제점을 보완하기 위해 1T-DRAM이 제안되었다. 1T-DRAM은 하나의 트랜지스터로 이루어져 있으며 SOI (silicon-on-insulator) 기판에서 나타나는 floating body effect를 이용하여 추가적인 캐패시터를 필요로 하지 않는다. 하지만 SOI 기판을 이용한 1T-DRAM은 비용측면에서 대량생산화를 시키기는데 어려움이 있으며, 3차원 적층구조로의 적용이 어렵다. 하지만 다결정 실리콘을 이용한 기판은 공정의 대면적화가 가능하고 비용적 측면에서 유리한 장점을 가지고 있으며, 적층구조로의 적용 또한 용이하다. 본 연구에서는 ELA (eximer laser annealing) 방법을 이용하여 비정질 실리콘을 결정화시킨 기판에서 1T-DRAM을 제작하였다. 하지만 다결정 실리콘은 단결정 실리콘에 비해 저항이 크기 때문에, 메모리 소자로서 동작하기 위해서는 높은 바이어스 조건이 필요하다. 게이트 산화막이 얇은 경우, 게이트 산화막의 열화로 인하여 소자의 오작동이 일어나게 되고 게이트 산화막이 두꺼울 경우에는 전력소모가 커지게 된다. 그러므로 메모리 소자로서 동작 할 수 있는 최적화된 게이트 산화막 두께가 필요하다. 제작된 소자는 KrF-248 nm 레이저로 결정화된 ELA 기판위에 게이트 산화막을 10 nm, 20 nm, 30 nm 로 나누어서 증착하여, 전기적 특성 및 메모리 특성을 평가하였다.