• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.965-973
• /
• 2010

Numerical analysis has been carried out to investigate the heat transfer characteristics of a plate heat exchanger. The multi-cell models with inlet part and outlet part are used for performing numerical simulation. The plate heat exchanger is characterized by chevron angle of $15^{\circ}$, corrugation pitch of 24mm and corrugation height 6~12mm. The length of the inlet-part considered in the analysis ranges from 24.8 to 124mm and Reynolds numbers range from 1,000 to 10,000. The correlations such as friction factor and Colburn factor are compared with previous experimental data. The results can be utilized for designing the plate heat exchanger.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.1
• /
• pp.1-8
• /
• 2012

Numerical analysis has been carried out to investigate the fully developed flow and heat transfer characteristics of a plate heat exchanger. Multi-cell models with an inlet part and outlet part are used to perform the numerical simulation. The plate heat exchanger is characterized by a chevron angle of $20^{\circ}$ and a P/H ratio of 2.0~4.0. The working fluid is water and the Reynolds numbers range from 300 to 1,500. The correlation is given in the form of $f=CRe^m$ for the friction factor and $j=CRe^m$ for the Colburn factor. It is found that the fully developed flow starts from the third cell and the Nusselt number increases with decreasing P/H ratios.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.7 no.2
• /
• pp.23-29
• /
• 2011

The objectives of this paper are to study the characteristics of heat transfer and pressure drop of the plate heat exchanger with corrugation height by numerical analysis. Plate heat exchanger of three types was designed, which was corrugation height 3.1mm, 2.8mm and 2.5mm. The plate heat exchanger was numerically investigated for Reynolds number in a range of 950~3,380. The temperatures of the hot side were performed at $14.5^{\circ}C$ while that of the cold side was conducted at $4.5^{\circ}C$. The results show that the performance of heat transfer coefficient for corrugation height 2.5mm increases about 9.5~17.1% compared to that of corrugation height 3.1mm. On the other hand, the performance of pressure drop for corrugation height 2.5mm is remarkably higher than that of corrugation height 3.1mm, about 65.7~86.0%.

• Journal of Korean Society of Disaster and Security
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2021

A corrugated pipe is widely used in firefighting equipment and sprinkler pipes because of its elasticity, which is less damaged by deformation and convenient facilities. However, the corrugated shape of the wall results in complex internal turbulent flow, and it is difficult to predict the pressure drop, which is an important design factor for pipe flow. The pressure drop in the corrugated tube is a function of the shape factors of the pipe wall, such as groove height, length, and pitch. Existing studies have only shown a study of pressure drop due to length changes in the case of D-shaped tubes with less than 5 pitch (P) and height (K) of the rectangular grooves in the tube. In this work, we conduct a numerical study of pressure drop for P/Ks with length and height changes of 2.8, 3.5 and 4.67 with Re Numbers of 55,000, 70,000 and 85,000. The pressure drop in the corrugated tube was interpreted to decrease with smaller P/K. We show that the pressure drop is affected by the change in the groove aspect ratio, and the increase in the height of the groove increases the recirculation area, and the larger the Reynolds number, the greater the pressure drop.

• Journal of Adhesion and Interface
• /
• v.23 no.2
• /
• pp.39-43
• /
• 2022

In optoelectronic devices including displays and solar cells that convert electricity into light or light into electricity, it is important to control optical behavior of light to improve device efficiency. Specifically, the control of internal emitting light in the OLEDs can induce more light to go out, improving luminous efficiency. In addition, the control of optical behavior of incident light in solar cells can increase optical path in the light absorption layer, increasing power-conversion efficiency. In this study, we generated wrinkles as a physical structure to control optical behavior of light and independently controlled their wavelength and height by changing stress relaxation time. To explore the effect of wavelength and height on optical behavior, we conducted UV/Vis spectroscopy analysis of wrinkles with various heights at a constant wavelength or various wavelengths at a comparable height, figuring out a wrinkle with high aspect ratio has more dispersive light and less straight light. It indicates that high aspect ratio is required to change the optical behavior and increase the optical path.

• Journal of the Korean Institute of Gas
• /
• v.15 no.4
• /
• pp.39-43
• /
• 2011

In this study, the stress and deformation behavior characteristics of a flexible joint for a gas pipe have been analyzed by a finite element method. These characteristic results may investigate the strength safety analysis of a flexible joint, which is composed by a spiral corrugation pipe or a rectangular corrugation model and a plane pipe. The FEM computed results show that an optimized spiral corrugation pipe model is a inclined angle of $4.7^{\circ}$ and a corrugation height of 1.5mm. And also, a rectangular corrugation pipe model of $90^{\circ}$ is recommended in strength safety rather than a spiral corrugation pipe with an inclined angle. Thus, a corrugated pipe for an increased strength safety is to recommend a reduced pitch and curvature radius of an inclined corrugation.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.1
• /
• pp.11-18
• /
• 2012

In this paper, the occurrence of a stopband phenomenon when an acoustic wave propagates through periodically corrugated ducts is discussed using theoretical and BEM analyses. A 2-D duct with sinusoidally corrugated upper and lower walls is considered. When the magnitude of the sinusoidal corrugation is sufficiently small compared to the duct's height, the wave equation is solved with the multiple scaling perturbation method. Then stopbands for Bragg and non-Bragg resonances are computed from the condition where frequency becomes a complex number. A 2-D BEM analysis is performed to compute insertion loss of the duct, and stopbands are confirmed as predicted by analytical analysis.

• Fashion & Textile Research Journal
• /
• v.1 no.3
• /
• pp.252-258
• /
• 1999

The aims of this study is to classify the lower somatotype of adult women and appearance analysis on the shape of flare skirts by using the image processing. Also We have made skirts in order to analyze the various types of appearance of flare skirts by using the image processing. The subjects for our wear test lower somatotype, who were controlled in their waist, abdomen and hip shapes. The flare skirts used for wear test were 112 types(combinated 14 fabric type and 8 lower somatotype). The effect of lower somatotype on the shape of flare skirts was determined by the horizontally hem line section shape and the silhouette of flare skirts with image processing. The data were analyzed by using analysis of variance and Turkey, Duncan multiple range test. The results obtained are summarized as follows: It is shown that the fabric weight elongation differs in fabrics properties, in direction of textures. The shape horizontal section of flare skirt hem line has differed with the number of nodes, wave-height of nodes and breadth of silhouette by fabrics properties and lower somatotype. It is noticed that the breadth of flare skirts by the silhouette has high correlation with the drape ability of fabrics and lower somatotype. Results for our flare skirts show changes in amplitude and mean with fabrics, somatotype. Therefore we can say that gray-level histograms are correlated with changes in appearance, differences in drape spacing and related fabric properties and their somatotype.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.1
• /
• pp.39-45
• /
• 2024

Seismic safety of expansion joints for piping systems has been underscored by water pipe ruptures and leaks resulting from the Gyeongju and Pohang earthquakes. Metal bellows in piping systems are applied to prevent damage from earthquakes and road subsidence in soft ground. Designed with a series of corrugated segments called convolutions, metal bellows exhibit flexibility to accommodate displacements. Several studies have examined variations in convolution shapes and layers based on the intended performance to be evaluated. Nonetheless, the research on the seismic performance of complex bellows having multiple corrugation heights is limited. In this study, monotonic loading tests, cyclic loading tests, and fatigue tests were conducted to evaluate the shear performance in seismic conditions, of metal bellows with variable convolution heights. Single- and triple-layer bellows were considered for the experimentation. The results reveal that triple-layer bellows exhibit larger maximum deformation and fatigue life than single-layer bellows. However, the high stiffness of triple-layer bellows in resisting internal pressure poses certain disadvantages. The convolutions are less flexible at lower displacements and experience leakage at a rate related to the variable height of the convolutions in certain conditions. At lower deformation rates, the fatigue life is rated higher as the number of layers increase. It converges to a similar fatigue life at higher deformation rates.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.9
• /
• pp.1603-1613
• /
• 2001

본 연구는 동작분석장치를 이용하여 하지동작분석을 시도함으로서 실제 동작 시 적응 할 수 있는 의복설계를 위한 기초 자료로서 하지부 실루엣 변화의 특성을 밝히고자 하였다. 대퇴돌기점을 기준으로 본 하지동작의 진행방향 이동과 상향 방향이동을 살펴보았는데 보행유형에 따라 여유량이 특히 요구되는 부위가 각기 다르며, 부위별 필요 여유 량도 각기 다르다는 것을 알 수 있었으며 , 이러한 보행유형 별 스커트 실루엣의 특징은 기능복 설계 시 고려되어야 하겠다. 평지보행 시는 발목부위가 전면방향보다 후면방향으로 이동의 범위가 크므로 트임이나 주름이 뒷면에 있는 것이 적합하고, 계단승강이나 버스승강의 경우 무릎전면에 여유량이 필요하므로 주름이나 트임을 앞쪽에 주는 것이 바람직하며 그 길이는 대퇴돌기점 높이정도에서 시작하여야 하고 무릎아래에 있는 앞트임은 하지동작에 도움이 되지 않음을 알 수 있었다.