• Journal of Korean Society of Steel Construction
• /
• v.21 no.6
• /
• pp.563-574
• /
• 2009

This paper briefly describes the fundamental strategies--path-tracing, pin-pointing, and path-switching--in the computational elastic bifurcation theory of geometrically non-linear single-load-parameter conservative elastic spatial structures. The stability points in the non-linear elasticity may be classified into limit points and bifurcation points. For the limit points, the path tracing scheme that successively computes the regular equilibrium points on the equilibrium path, and the pinpointing scheme that precisely locates the singular equilibrium points were sufficient for the computational stability analysis. For the bifurcation points, however, a specific procedure for path-switching was also necessary to detect the branching paths to be traced in the post-buckling region. After the introduction, a general theory of elastic stability based on the energy concept was given. Then path tracing, an indirect method of detecting multiple bifurcation points, and path switching strategies were described. Next, some numerical examples of bifurcation analysis were carried out for a trussed stardome, and a pin-supported plane circular arch was described. Finally, concluding remarks were given.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.11
• /
• pp.520-526
• /
• 2019

I-type girders are widely applied as very economical sections in plate girder bridges. There has been research on developing composite laminated panels, curved plates reinforced with closed-end ribs, and new forms of ribs and compression flanges for steel box girders. However, there is a limitation in analyzing the exact cause of local buckling caused by an I-type girder's webs. Therefore, an I-type girder's web was modeled using the finite element analysis program LUSAS 17.0 before and after reinforcement. We checked for the minimum thickness criteria presented in the Korea highway bridge design code, and the cause of buckling after performing a linear elastic buckling analysis of dead and live loads was analyzed. Before reinforcement, an eigenvalue (λ₁) at the 1st mode was 0.7025, the critical buckling load was smaller than the applied load, and there is a buckling. After reinforcement, when applying vertical and horizontal stiffeners to the web part of the girder at support, a Nodal line was formed, the eigenvalue was 1.5272, and buckling stability was secured. To improve buckling trace of the girder at the support, an additional plate was applied to the web at the support to ensure visual and structural safety, but buckling occurs at center of web. The eigenvalue (λ₁) was 3.5299, and this method is efficient for reinforcing the web of the support.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.2
• /
• pp.87-94
• /
• 1998

Behavioral characteristics of shallow circular arches with dynamic loading and different end conditions are analysed. Geometric nonlinearity is modelled using Lagrangian description of the motion. The finite element analysis procedure is used to solve the dynamic equation of motion, and the Newmark method is adopted in the approximation of time integration. The behavior of arches is analysed using the buckling criterion and non-dimensional time, load and shape parameters which Humphreys suggested. But a new deflection-ratio formula including the effect of horizontal displacement plus vertical displacement is presented to apply for the non-symmetric buckling problems. Through the model analysis, it's confirmed that fix-ended arches have higher buckling stability than hinge-ended arches, and arches with the same shape parameter have the same deflection ratio at the same time parameter when loaded with the same parametric load.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.163-172
• /
• 2000

The postbuckling behavior and progressive damage of composite laminated cylindrical shell under uniform external pressure were investigated by nonlinear finite element method programming. For the finite element analysis, nine-node 3-D degenerated elements were utilized, and arc-length method including line search was adopted for the iteration and load-increment along postbuckling equilibrium path. As results. buckling load, postbucking behavior, and progressive failure f3r various composite laminated cylindrical shells were discussed.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.599-610
• /
• 2007

In this paper, we described a co-rotational formulation for the geometrical nonlinear analysis of three-dimensional frames. We suggested a new concept called the Zero-Twist-Section Condition (ZTSC) to decide the element coordinate system consistently. According to the ZTSC procedure, it is possible to obtain an element coordinate system and natural deformations consistently when finite displacements and rotations are induced in an element. Based on the developed procedure, numerical examples are investigated to calculate natural rotations while finite displacements are imposed on an element. Also, the developed co-rotational procedure gives accurate results in the analysis of post-buckling problems with finite rotations.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.465-468
• /
• 2011

압축을 받는 판 구조의 경제적인 단면 보강을 위해 종방향 보강재인 U형 단면 리브를 적용하는 것이 효과적이나, 현재 국내에서는 명확한 설계지침이나 연구자료가 제시되지 못하고 있다. 따라서 U리브의 적정 크기 및 최적 간격에 대해 검토 후 이에 관한 지침이 제시될 필요성이 있다. 이에, 본 연구에서는 U리브의 단면 크기 및 강성에 따른 탄성좌굴강도 및 좌굴모드의 변화를 알아보고자 한다. 유한요소해석 프로그램인 ABAQUS를 이용하여 고유치 해석을 실시하였고, 이론값과 해석적 결과의 탄성좌굴강도를 비교하였다. 이러한 분석 결과를 토대로 향후 U리브의 최소소요강성 및 단면 선정방안을 제시하는데 기여할 수 있을 것으로 기대된다.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.51-60
• /
• 2004

The stress analysis of cold-formed channel section steel beams under transverse load was conducted. The local buckling effect was included in the analysis using effective area concept. The proposed analytical model is capable of predicting accurate normal stress in the beam due to various behaviors including biaxial bending and warping. It was found to be appropriate for predicting stresses as well as deflection in the beam. A finite element model was developed to solve the analytical model.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.36 no.3
• /
• pp.193-201
• /
• 2023

In this study, a nonlinear truss finite element is developed to analyze structures with negative Poisson effect-induced tensile buckling. In general, the well-known buckling phenomenon is a stability problem under a compressive load, whereas tensile buckling occurs because of local compression caused by tension. It is not as well-known as classical buckling because it is a recent study. The mechanism of tensile buckling can be briefly explained from an energy standpoint. The nonlinear truss finite element with a torsional spring is formulated because the finite element has not been reported in the literature yet. The post-buckling analysis is then performed using the generalized displacement control method, which reveals that the torsional spring plays an important role in tensile buckling. Structures that mimic a negative Poisson effect can be constructed using such post-buckling behaviors, and one of the possible applications is a mechanical switch. The results obtained are compared to those of analytical solutions and commercial finite element analysis to assess the validity of the proposed finite element model. The numerical results show that the developed finite element model could be a viable option for the basic design of nonlinear structures with a negative Poisson effect.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2A
• /
• pp.81-92
• /
• 2010

In design of steel frames, it is generally believed that elastic system buckling analysis cannot predict real behaviors of structures, while inelastic system buckling analysis can give informative buckling behaviors of individual members considering inelastic material behavior. However, the use of Euler buckling equation with these system buckling analyses have the inherent problem that the methods evaluate unexpectedly large effective lengths of members having relatively small axial forces. This paper proposes a new method of obtaining elastic and inelastic effective lengths of all members in steel frames. Considering a fictitious axial force factor for each story of frames, the proposed method determines the effective lengths using the inelastic stiffness reduction factor and the iterative eigenvalue analysis. In order to verify the validity of the proposed method, the effective lengths of example frames by the proposed method were compared to those of previously established methods. As a result, the proposed method gives reasonable effective lengths of all members in steel frames. The effect of inelastic material behavior on the effective lengths of members was also discussed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.11
• /
• pp.865-873
• /
• 2013

In this paper, numerical methods for wrinkle prediction of thin membrane were studied by finite element analysis. Techniques using membrane and shell elements were applied for triangular membrane. In case of membrane element method, the wrinkling was accounted for by the wrinkle algorithm of property modification, which was implemented to ABAQUS as a user subroutine. In case of shell method, geometrically nonlinear post-buckling analysis was performed to obtain the wrinkle deformation explicitly. The wrinkling deformation was induced by seeding the mesh with a random geometric imperfection. The results were investigated focusing on the mesh convergence and the solution accuracy.