• 분석과학
• /
• 제10권3호
• /
• pp.225-229
• /
• 1997

졸겔법에 의해 제조된 organically modified silicate(Ormosil)에 Rhodamine 6G perchlorate(Rh6GP)를 침투시켰으며, 이 유기염료가 무기/유기 복합 기저체(host)에 안정하게 침투되었는지를 확인하였다. 복합졸의 상태에서 측정된 유기염료의 흡수스펙트럼과 겔화된 후의 스펙트럼, 그리고 복합체가 완전히 건조된 상태에서의 스펙트럼을 비교하여 Rh6GP가 이합체화되지 않고 안정한 상태로 있을 수 있는 Ormosil의 조성을 확립하였다. 졸겔반응시의 촉매로 사용된 염산의 농도가 Tetraethyl orthosilicate(TEOS) 1몰을 기준으로 0.1몰 이내의 범위에서만 유기염료가 안정하고 이합체화되지 않은 상태가 유지되었다.

• 한국세라믹학회지
• /
• 제31권8호
• /
• pp.911-919
• /
• 1994

As the study for preparation of single-layer anti-reflective coating on glass, the conditions of synthesis of sol for coating and of reproducible coating procedure were investigated. In case of water-based sol, coating was impossible because of poor wettability of sol. The Substitution of solvent with ethanol improved the wettability of sol on the glass surface, and optimum amount of ethanol for substitution was 70 vol%. Maximum specific surface area and total pore volume of water-based sol were 268.7$m^2$/g and 0.315 cc/g, but after substitution, those values increased to 404.1 $m^2$/g and 0.376 cc/g, respectively. The upper limit withdrawl speed of coating in order to get clean coated films without aggregations or stains was 7 cm/min. In case of addition of 0.1 mol HNO3 and substitution with 70 vol% ethanol and heat-treatment at 40$0^{\circ}C$ for 1 hour, thin film with thickness of 94 nm was obtained at withdrawl speed of 4 cm/min. The thickness of thin film was independent of drying time.

• 한국전기전자재료학회논문지
• /
• 제25권8호
• /
• pp.620-625
• /
• 2012

The sol-gel method has been widely used to synthesize the $TiO_2$ for dye sensitized solar cells and has advantages of easily fabrication process, controlling the $TiO_2$ phase and getting transparent thin-film composed of the $TiO_2$. In this paper, we synthesized the crystalline $TiO_2$ by sol-gel method controlled by the quantity ratio of Nitric acid and Ammonium hydroxide additives. The best efficiency result was obtained by 0.05 M Ammonium hydroxide and that results of Voc, Jsc, FF, and efficiency were 0.68 V, 3.28 mA/$cm_2$, 58.14 and 5.21%, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1328_1329
• /
• 2009

Nano porous indium tin oxide (ITO) powder was synthesized employing a new route sol-gel combustion hybrid method using Ketjen Black as a fuel. The nano porous ITO powder was composed of $SnCl_4$-98.0% and $In(NO_3)_3{\cdot}XH_2O$-99.999%, produce with a $NH_4OH$ with sol-gel method as a catalyst [1,2]. Crystal structures were examined by powder X-ray diffraction (XRD), and those results show shaper intensity peak at $25.6^{\circ}(2{\Theta})$ of $SnO_2$ by increased sintering temperature. A particle morphology as well as crystal size was investigated by scanning electron microscopy(FE-SEM), and the size of the nano porous powder was found to be in the range of 20~30nm. ITO films could controlled by nano porous powder at various sintering temperature in this paper[3,4]. The sol-gel combustion method was offered simple and effective route for the synthesis of nano porous ITO powder[5].

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1240_1241
• /
• 2009

In this paper, sol-gel-spin coated $Pb(ZrTi)O_3$ thin film with $ZrO_2$ buffer-layer and $PbTiO_3$ seed-layer was investigated for vibration MEMS energy harvester to scavenge power from ambient vibration via d33 piezoelectric mode. Piezoelectric thin film deposition techniques on insulating layer is the important key for $d_{33}$ mode of piezoelectric vibration energy harvester. $ZrO_2$ buff-layer was utilized as an insulating layer. $PbTIO_3$ seed-layer was applied as an inter-layer between PZT and $ZrO_2$ layer to improve the crystalline of PZT thin film. The fabricated PZT thin film had a remanent polarization of 5.3uC/$cm^2$ and the coercive field of 60kV/cm. The fabricated energy harvester using PZT thin film with PTO seed-layer generated 1.1uW of electrical power to $2.2M{\Omega}$ of load with $4.4V_{pvp}$ from vibration of 0.39g at 528Hz.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권3호
• /
• pp.128-132
• /
• 2004

The perovskite ferroelectric materials of the PZT, SBT and BST series will attract much attention for application to ULSI devices. Among these materials, the BST ($Ba_0.6$$Sr_0.4$/$TiO_3$) is widely considered the most promising for use as an insulator in the capacitors of DRAMS beyond 1 Gbit and high density FRAMS. Especially, BST thin films have a good thermal-chemical stability, insulating effect and variety of Phases. However, BST thin films have problems of the aging effect and mismatch between the BST thin film and electrode. Also, due to the high defect density and surface roughness at grain boundarys and in the grains, which degrades the device performances. In order to overcome these weakness, we first applied the chemical mechanical polishing (CMP) process to the polishing of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. BST ferroelectric film was fabricated by the sol-gel method. And then, we compared the surface characteristics before and after CMP process of BST films. We expect that our results will be useful promise of global planarization for FRAM application in the near future.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1030-1035
• /
• 2001

Strontium barium niobate, (Sr$\sub$0.5/Ba$\sub$0.5/Nb$_2$O$\sub$6/), thin films of various composition were prepared by the sol-gel method. Solution derived from acetate powders and niobium ethoxide in a mixture of acetic acid, ethylene glycol and 2-methoxyehanol was spin-coated onto bare silicon, Pt-coated silicon and fused silica substrates. Processing parameters were optimized to develop stable solutions which yielded films with relatively low crystallization temperatures. It was determined that ethylene glycol was a necessary component of the solution to increase stability against precipitation and to decrease the crystallization temperature of the films as confirmed by XRD and FT-IR analyses.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권8호
• /
• pp.836-850
• /
• 1996

In this study, we have analyzed structural analysis and measured ferroelectric characteristics of PZT thin films prepared by sol gel process with different sintering conditions and different Zr/Ti mot%. When the Zr mot% of PZT thin film was increased, it was found that the remanent. polarization and coercive field were decreased and increased, respectively. Also, the maxium dielectric constant of PZT(50/50) thin film was 786.8. We got double hysteresis(anti-fcrroelectric) curve from PbZrO$_{3}$ thin film. As heating rate goes up, pyrochlore phase of PZT thin film was decreased and dielectric and ferroelectric characteristics were improved. As a result of variation of sintering temperature and time 500.deg. C-800.deg. C and 5 sec.-8 hours, respectively, we got optimal sintering temperature and time. The optimium sintering temperature and time of conventional furnace method and rapid thermal processing method were 650.deg. C-700.deg. C for 30-60 minutes and 700.deg. C/20 seconds-2 minutes, respectively.

• 대한화학회지
• /
• 제41권3호
• /
• pp.130-137
• /
• 1997

육방형 이황화 티탄늄의 분말과 박막을 졸-겔법을 변형시켜 제조하였다. 여러 가지 용매하에서 이소프로폭시화 티탄늄과 황하 수소와의 반응에 의해 전구체의 침전을 유도한 후 이것을 황화 수소 분위기에서 열처리를 하면 분말이 얻어지는 반면 2-메톡시에톡시화 티탄늄과의 반응은 안정한 전구체 용액을 주므로 이것을 스핀 코팅하여 열처리하면 박막을 얻을 수 있다. 이러한 분말과 박막의 형태 변화를 열처리를 하면서 전자 현미경과 분말 X-선 회절기를 통해 살펴보았다.

• 한국세라믹학회지
• /
• 제31권10호
• /
• pp.1231-1239
• /
• 1994

In this study, gel powder which had relatively high hydration reactivity in CaO and P2O5 rich composition of CaO-P2O5-SiO2-H2O system was prepared by sol-gel process and its hydrated specimen was manufactured. The it was investigated to appropriate calcination temperature in sol-gel process which hydrated specimen of gel powder have proven to strength and the effect of factors influenced strength in hydration process. The major product of before and after hydration reaction was hydroxyapatite, and crystalline phase of C-S-H was already formed during gelation process. After hydration reaction of pressed specimen, crystalline phase of C-S-P-H was formed. It was hydrated product of silicocarnotite (5CaO.P2O5.SiO2). Gel phases of C-S-H and C-S-P-H occured as a result of partial substitution of amorphous silica by P2O5 was formed. The strength of hydrated hardened body is developed by strong bonding and bridging between the gel phases of C-S-H or C-S-P-H and the crystalline products such as hydroxyapatite, Ca(OH)2 C-S-H and C-S-P-H. In addition, the ultrafine gel powder have an great effect on increase of hydration reaction.