• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.9
• /
• pp.1-12
• /
• 1998

We have implemented receiver for a 3 Dimensional Phased-Array Radar detecting the azimuth angle, the altitude, the range of a target on real time. This system consists of high frequency module, which protects receiver and controls sensitivity, intermediate frequency module, monopulse detector, IQ phase detector, AGC controller. A two-channel receiver with same function is implemented for increasing accuracy of target altitude data by amplitude comparison monopulse method. The TSS sensitivity of the receiver is -98dBm. The bandwidth of the receiver is 500 MHz. We can control the system gain manually by 100 dB when be AGC off. The gain and phase unbalance of two channels is 5 dB and 30 degree, respectively. The image rejection rate of the IQ detector is 30 dB. We used duroid substrate and package- type device.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.12
• /
• pp.90-95
• /
• 2014

This paper presents a VHF/UHF-band variable gain low noise amplifier for multi-standard mobile TV tuners. A proposed VHF-band variable gain amplifier is composed of a resistive shunt-feedback low noise amplifier to remove external matching components, a single-to-differential amplifier with input PMOS transcoductors to improve low frequency noise performance, a variable shunt-feedback resistor and an attenuator to control variable gain range. A proposed UHF-band variable gain amplifier consists of a narrowband low noise amplifier with capacitive tuning to improve noise performance and interference rejection performance, a single-to-differential with gm gain control and an attenuator to adjust gain control range. The proposed VHF-band and UHF-band variable gain amplifier were designed in a $0.18{\mu}m$ RF CMOS technology and draws 22 mA and 17 mA from a 1.8 V supply voltage, respectively. The designed VHF-band and UHF-band variable gain amplifier show a voltage gain of 27 dB and 27 dB, a noise figure of 1.6-1.7 dB and 1.3-1.7 dB, OIP3 of 13.5 dBm and 16 dBm, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.10A
• /
• pp.1223-1229
• /
• 2004

A variable-gain low-voltage low noise amplifier MMIC operating at 5GHz frequency band is designed and implemented using the ETRI 0.5$\mu\textrm{m}$ GaAs MESFET library process. This low noise amplifier is designed to have the variable gain for adaptive antenna array combined in HIPERLAN/2. The feedback circuit of a resistor and channel resistance controlled by the gate voltage of enhancement MESFET is proposed for the variable-gain low noise amplifier consisted of cascaded two stages. The fabricated variable gain amplifier exhibits 5.5GHz center frequency, 14.7dB small signal gain, 10.6dB input return loss, 10.7dB output return loss, 14.4dB variable gain, and 2.98dB noise figure at V$\_$DD/=1.5V, V$\_$GGl/=0.4V, and V$\_$GG2/=0.5V. This low noise amplifier also shows-19.7dBm input PldB, -10dBm IIP3, 52.6dB SFDR, and 9.5mW power consumption.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.1
• /
• pp.1-10
• /
• 2003

This paper is concerned with the fuzzy control scheme and PID controller for the vibration suppression control of a cantilever beam equipped with a laser sensor and an electromagnetic actuator. The PID controller is being widely used in industrial applications. However, it is difficult to determine the appropriate PID gains in nonlinear systems and systems with time variant characteristic and so on. In this paper, we design the fuzzy based PID controller of which output gains are adjusted automatically and the designed controller is applied to active vibration control of a cantilever beam using electromagnetic actuator with strong nonlinearity. The tuning PID parameters of proposed controller are determined by using Fuzzy algorithm. Effectiveness and performance of the designed controller are verified by both simulation and experiment results. Experimental results demonstrate that better control performance can be achieved in comparison with the PID cotroller.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.42-49
• /
• 2004

This paper presents a new method of external load disturbance compensation using deadbeat load torque observer and gain compensation by parameter estimator. The response of the permanent magnet synchronous motor(PMSM) follows the nominal plant. The load torque compensation method is composed of a deadbeat observer. To reduce the noise effect, the post-filter implemented by moving average(MA) process is adopted. The parameter compensator with recursive least square method(RLSM) parameter estimator is suggested to make the new system work as same as the name plate system which in used to take gains. The proposed estimator is combined with a high performance load torque observer to resolve the problems. As a result, the proposed control system has a robust and precise system against the load torque and the parameter variation. A stability and usefulness are verified by computer simulation and experiment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.3A
• /
• pp.160-167
• /
• 2005

The gain-clamped EDFA has been developed to eliminate the output power change of WDM surviving channels to occur with added or dropped channels, which degrades the performance of WDM optical network. It maintains the constant gain of surviving channels when WDM channels are added or dropped in a network amplifying node. In this paper, the hi-directionally pumped gain-clamped EDFA is implemented to compensate the change of the input power by a lasing. The results show that the lasing of a short wavelength and backward propagation is the optimal condition to minimize the transient response of surviving channels in terms of the overshoot and gain saturation due to the inhomogeneous broadening effect.

• Korean Journal of Optics and Photonics
• /
• v.12 no.3
• /
• pp.200-204
• /
• 2001

The structural design and the measured characteristics of optical signal amplification unit for 640 Gbps (10 Gbps$\times$64 ch.) WDM transmission systems are reported. The unit is composed of two sub gain block units for the amplification of C-band (1530-1560 nm) and L-band (1570-1600 nm), respectively. Programmable microprocessors monitor the states of operation and optimize the optical output conditions. Each sub gain block unit can maintain total optical output power of +21 dBm with gain flatness of < 1 dB and noise figure of <7.2 dB for the input power in the dynamic range from-5 to +1 dBm.+1 dBm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1402-1409
• /
• 2007

In this paper, we propose various types of AGC algorithms for implementing the OFDM communication systems. For the high-speed packet transmission, in this paper, we assume the OFDM system with relatively long and repeated preambles. We propose the maximum sample value counter for counting the number of maximum sample. In the maximum sample value counter, we use the buffer for the digital signal buffering. Finally, the counting value of the maximum sample value counter controls the gain control signal generator by using gain control table automatically.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1758-1759
• /
• 2011

본 논문은 비선형 시스템의 소속함수 의존성을 이용한 관측기 기반 퍼지 제어기 설계 기법을 제시한다. Takage-Sugeno (T-S)퍼지 모델링을 이용해 비선형 시스템을 퍼지 모델로 표현한다. 시스템의 안정화 조건은 소속함수의 의존성을 이용한 리아푸노프 안정도 해석 방법을 이용해 유도된다. 안정화 조건은 선형 행렬 부등식으로 표현되며, 부등식의 해를 이용해 제어기의 이득값을 구한다. 모의실험을 통해 설계된 제어기의 타당성을 검증한다.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.75-76
• /
• 2008

이산시간 모델로부터 시간응답 설계 명세를 만족시키도록 직접 디지털 제어기를 설계하는 새로운 방법을 제시한다 R-S-T형의 고정된 제어기 구조에서 폐루프 전달함수가 원하는 기준전달함수와 일치하도록 제어기 이득을 구한다. 시간 응답을 만족시키는 목표전달함수는 w-영역에서 CRA를 이용하여 선택되며 이 함수를 z-영역으로 변환시켜 얻는다. 예제를 통해 제시한 방법의 유용성을 보이고 극배치 방식과 비교한다.