• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.499-502
• /
• 2017

The needs of efficient electricity use and current measurement for electrical safety have been increased. Hence, the current sensor is used, especially non-contact current sensor which can measure the current without blocking the circuit using hall effect. However, the accurate measuring of the current sensor is inhibited due to the inflow of various noises in this current sensor. In this article, a stronger current sensor against the noise is proposed using low pass FIR filter to the existing current sensor. FIR filter was designed to block the range over the certain frequency at the output of the current sensor to eliminate the external noises, and so on. As a result, more accurate and close measurements were possible.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.1
• /
• pp.57-63
• /
• 2001

The wound rotor type induction motor(WRIM) control system which is widely used in the industry has many maintenance problem because of external resistors and magnetic contactors. In this paper, the simple sensorless vector control algorithm for WRIM is proposed without any additional devices except detecting rotor currents. Because the external resistors are disconnectd and the rotor slip rings are shorten, the power loss due to external resistors is removed and the maintenance problem is improved remarkably. Also, the vector control performance becomes better because the proposed sensorless vector control algorithm does not use the rotor resistance which is usually used to estimate the slip frequency in case of indirect vector control scheme. The proposed algorithm is verified by the digital simulation and the experiment.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.6
• /
• pp.581-588
• /
• 2014

The PSC bridges have recently been widely used in Korea. The PSC bridge is a structure whose performance is improved through the use of tendons and steel bars in deflection and cracking characteristics of the concrete. Therefore, measurement or estimation of the load acting on tendon is important in order to maintain the PSC bridges efficiently and safely. This paper deals with a numerical study on the deformation of a multi-tendon anchor head in order to verify the relationship between the load acting on tendon and the deformation of anchor head. All kinematics, material properties and contact nonlinearity are included for the precise analysis and numerical studies are performed by Abaqus. From the numerical results, it is verified that the hoop strain is most useful in the estimation of the load acting on tendon and strains are affected by various parameters such as friction coefficient, boundary conditions, and arrangement.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.5
• /
• pp.113-120
• /
• 2013

Graphite is commonly used as a solid lubricant leading to low friction coefficient and abrasion. In this study, wear behavior of sealing graphite(HK-6) at elevated temperature was evaluated. Reciprocating wear test was carried out as wear occurred graphite as a seal(HK-6) is positioned between the liner and driving shaft. Variables which are temperature, sliding speed and contact load are set. This study suggest optimized environment conditions through the wear properties of graphite.

• Korean Journal of Optics and Photonics
• /
• v.26 no.5
• /
• pp.261-264
• /
• 2015

In this paper we show that the photoresist-protective film of a printed circuit board (PCB) can be delaminated from the underlying photoresist layer by a single pulse of a nanosecond laser at 532 nm. After locally peeling the edge of the PCB with a laser beam of 9 mm size, Scotch tape was attached to the irradiated region to peel off the whole protective film. For a certain range of pulse energies the peeling probability was 100%, without leaving any damage. Since the use of a laser in initial delamination is noncontact and nondamaging, it may be more efficiently utilized in the PCB industry than the conventional knurling method based on mechanical pressing.

• Korean Journal of Optics and Photonics
• /
• v.20 no.5
• /
• pp.276-280
• /
• 2009

A Cr:YAG crystal was used as a saturable absorber for passive Q-switching of a Nd:$YVO_4$ laser which was pumped by a 1-W continuous wave laser diode. The first surface of the Cr:YAG was high-reflection coated for the pump wavelength. The high-reflection coating improved the absorption efficiency of the pump beam in the Nd:$YVO_4$ through double pass absorption. It also prevented pump beam induced partial bleaching of the Cr:YAG. The peak-to-peak pulse fluctuation of passively Q-switched laser output was approximately 4 %. The minimum pulse-width was measured to be 7.11 ns. Also, the average pulse repetition rate was 9 kHz and the maximum output power was 16.27 mW.

• Journal of Aquaculture
• /
• v.13 no.2
• /
• pp.137-145
• /
• 2000

Capacity of water treatment of the three phase fluidized bed reactor as a biofilter in the seawater recirculating system was evaluated. The water treatment system consists of fluidized bed reactor for ammonia removal, cartridge filter for solid removal and ozone contactor for disinfection. Mean concentration of water quality parameters: COD, TAN, $NO_2$-N, $NO_3$-N, SS and alkalinity were 9.0, 0.22, 0.05, 20.0, 9.5 and 70.0 mg/l, respectively; the relevant values were 7.6 for pH and 3.64 NTU for turbidity. These indicate the maintenance of good water quality by the treatment system. The influent TAN loading rate in to the fluidized bed reactor ranged from 4.3 to 32.9 g/$m^3$/day, and averaged to 20 g/$m^3$/day. TAN removal efficiency of each phase of the fluidized bed reactor was 47-60%, indicating the effective ammonia removal. During operation the effluent of fluidized bed reactors also maintained the unionized ammonia nitrogen level below 0.002 mg/l.

• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.55-59
• /
• 2018

In this study, to overcome a complicated shoe adhesion process such as buffing, pre-treatment by primer in the rubber component of the shoe, we studied adhesion mechanical properties with rubber compound added water-soluble salt for the purpose of improving the adhesion between midsole and outsole. Acid salts, basic salt and neutral salts were evaluated, rubber containing basic salts showed excellent adhesion to water-based adhesion. Since the basic salt is present as the hydroxy salt, the surface of rubber is hydrophilized. The results are confirmed by contact angle and IR spectroscopy measurement. In addition, in the case of rubber compound added basic salts, NBS abrasion resistance and hardness were increased by increasing crosslink density, but crosslink time was delayed.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.27 no.6
• /
• pp.1499-1506
• /
• 2017

The use of smartphones and the launch of various apps have increased exponentially, and malicious apps have also increased. Existing app recommendation systems have been limited to operate based on static information analysis such as ratings, comments, and popularity categories of other users who are online. In this paper, we first propose a robust app recommendation system that realistically uses dynamic information of apps actually used in smartphone and considers static information and dynamic information at the same time. In other words, this paper proposes a robust Android app recommendation system by partially reflecting the time of the app, the frequency of use of the app, the interaction between the app and the app, and the number of contact with the Android kernel. As a result of the performance evaluation, the proposed method proved to be a robust and efficient app recommendation system.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2002.04b
• /
• pp.1563-1566
• /
• 2002

The increase of vehicles stagnations leads to the increasing attention to the way customers pay and a large number of projects on electronic cash system. Tranport system is comprised of a number of advanced technologies, including information processing, communications, control, and electronics. Recently many research on a system which provides contact in order to protect driver is vehicle passage have been carried out. And some potential problems from that system are being reviewed by electronic cash system. In this papers, we suggest RF protocol developing technology using the concept of electronic cash. ATM electronic cash developing is consist of component of pre-developed coin throw, integration of component using its, and production of more requirement-satisfactory ITS solution. Result increase $15{\sim}40%$ pre-type vehicles stagnations. Especially, we expect this proposed concept would be well adapted to our national environments.