Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
/
1986.11a
/
pp.47-51
/
1986
로울러 베어링의 로울러는 길이방향으로 적당하게 Profiling하여 양단부에서 발생하는 응력집중을 줄이고 있다. 로울러와 레이스간의 접촉을 단순한 탄성접촉문제로 해석하는 경우에는 유막의 개념이 없어서 로울러와 레이스 사이의 압력분포와 유막형상을 정확하게 나타내기가 어려우므로 탄성변형과 압력에 따른 윤활유의 점도 변화를 고려한 탄성유체윤활(EHL)해석이 필요하다. 대부분의 해석은 무한장 로울러로 취급하는 것이 보통이며 실제의 로울러에 해당하는 유한한 길이의 선접촉 EHL 해석은 Mostofi & Gohar 및 Kuroda & Arai의 해석 정도이나 각각은 수렴하중이 작거나 로울러의 길이가 아주 짧은 경우에 해당한다. 본 연구에서는 FDM과 Newton-Raphson method를 이용하여 길이가 유한한 실제 크기의 Profiled 로울러에 대한 EHL상태에서의 압력분포와 유막형상을 보다 하중이 온 경우에 대해서 구하고자 한다.
Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
/
1994.06a
/
pp.65-71
/
1994
유압 실린더용 유패킹의 접촉력, 접촉폭, 돌출발생 임계압력을 밀봉간극에 대하여 유한요소법을 이용하여 수치적으로 해석하였다. 초기 간섭량이 증가함에 따라 접촉력 및 접촉폭은 급격하게 증가하였다. 그러나 유압이 작용하는 상태에서 밀봉간극이 감소하면 시일의 돌출현상이 발생하는 임계압력은 보다 가파르게 증가함을 확인하였다. 초기 간섭량에 의한 접촉력으로 부터 유압 실린더의 누설에 관련된 사용 최저 유압을 연계하여 갑섭량이 설계되어야하고, 돌출발생 임계압력으로 부터는 사용 최고유압과 관련하여 간극이 설계되어야 하므로 이에 대한 수치해석적 설계자료를 제시하였다. 특히 시일립부의 접촉면을 나타내는 축방향에 따라서 접촉력 분포는 시일립 선단부와 돌출현상에 따른 상호 복잡한 결과의 중요성을 제시하였다. 이 결과는 윤활해석을 위한 탄성유체윤활 해석시 입력자료로 사용될 수 있어 실제 유막두께 해석 및 유동해석을 통하여 누설량 예측 등에 이용될 수 있는 설게자료이다.
Proceedings of the Korean Society for Emotion and Sensibility Conference
/
2002.05a
/
pp.357-360
/
2002
직물의 질감을 객관화시키는 연구는 고부가가치의 의류제품을 생산하고 판매하는데 매우 중요한 요소이다. 질감은 직물의 역학적 성질과 표면상태에 따라 좌우되며, 이의 측정방법 중에서 KES-F system이 가장 객관화되어 있다. KES-F system을 이용한 표면 거칠기 측정방법은 피아노선을 굴곡 시켜 일정한 힘을 가한 상태에서 직물의 표면을 문질러 측정하므로 직물의 표면을 문질러 측정하므로 직물 표면의 잔털이 눌려진 상태여서 질감해석을 위한 정확한 측정이 어렵다. 따라서 우리는 기하학적인 직물 표면의 거칠기를 표면의 변형없이 측정 가능한 레이저 센서를 사용하였다. 한편 직물의 주로 경사ㆍ위사로 짜여져 있어 이방성 성질을 가지고 있으므로 직물을 3방향으로 측정하여 해석하였다. 측정된 신호는 FET를 이용하여 일정한 주기의 표면형태를 구하고, 표면 높낮이의 평균, 최저값과 최고값을 구하여 표면의 특성을 얻었다. 직물 표면에 존재하는 잔털은 영상처리장치를 이용하여 양을 측정하였으며 표면의 거칠기 측정결과와 비교 분석하여 레이저 센서를 이용한 비접촉식 측정방법의 오차분석 및 표면 특징을 해석하였다.
Bulletin of the Society of Naval Architects of Korea
/
v.11
no.1
/
pp.35-44
/
1974
열박음(shrink fitting)으로 인(因)한 동심형(同心形) 구멍을 가진 복합(複合)실린더의 과도적(過渡的) 온도분포(溫度分布), 열응력(熱應力) 및 열변형도(熱變形度)를 이론해석(理論解析)하였다. 온도분포해석(溫度分布解析)에서 외부(外部) 실린더는 균일온도(均一溫度)로 가열(加熱)되어, 실온(室溫)의 내부(內部) 실린더와 접촉면(接觸面)에서 일어나는 열전도(熱傳導)에 의(依)하여 냉각(冷却)되고, 외부(外部) 표면(表面)은 대기중(大氣中)에 노출(露出)된 상태(狀態)로 취급(取扱)하였다. 열응력(熱應力)은 평면변형도조건(平面變形度條件)을 만족(滿足)하는 것으로 생각하였으며, 물성(物性)은 온도(溫度)에 무관(無關)한 상수(常數)로 취급(取扱)하였다. 온도분포(溫度分布)는 열전도문제(熱傳導問題)만을 고려(考慮)함으로서도 유효(有效)한 해(解)를 얻을 수 있으며 열응력(熱應力)은 접촉면(接觸面)에서부터 형성(形成)되며, 반경방향응력(半徑方向應力)은 시간(時間)이 경과(經過)함에 따라 압축응력(壓縮應力)이 증가(增加)하여 접촉면(接觸面)에서 최대치(最大値)를 갖고, 원주방향응력(圓周方向應力)은 접촉면(接觸面)에서 초기(初期)부터 거의 최종상태(最終狀態)와 같은 크기를 갖음을 알 수 있다. 균일온도분포(均一溫度分布)가 이루어지면 열응력(熱應力)의 형성(形成)은 완료(完了)되게 되며, 이때의 열응력(熱應力)의 크기와 분포경향(分布傾向)은 평면응력조건(平面應力條件)을 사용(使用)하였다는 사실(事實)을 고려(考慮)하면 $Lam\acute{e}$의 이론해(理論解)와 일치(一致)함을 알 수 있었다.
Proceedings of the Korean Nuclear Society Conference
/
1998.05a
/
pp.571-576
/
1998
고온의 증기가 과냉각 상태의 물과 직접접촉에 의해 발생하는 응축현상(DCC Direct Contact Condensation)을 실험적으로 고찰하였다. 본 연구는 두단계로 나누어 수행하였다. 1단계 연구에서는 간단한 원형관 형태의 수평 노즐을 통하여 증기제트가 대기압 상태의 과냉각수로 분출될 때 증기제트 및 주위의 거동을 측정·분석하였다. 수조의 온도와 증기유량의 변화에 따른 증기제트의 축방향과 반경방향 온도분포와 수조 벽면에서의 동압을 측정하였으며, 고속 비디오 카메라를 사용하여 각각의 경우에 대하여 증기제트의 분출이미지를 촬영하였다. 벽면에서의 동압은 노즐의 분출구직경과 응축수의 온도에 비례하여 증가하였다. 2단계 연구에서는 몇가지 형태의 증기분사기 축소 모형에 대한 응축성능을 비교하였다. 이때에는 수조의 온도상승으로 인해 수조가 가압되는 정도를 알아보기 위해 수조를 밀봉한 상태로 실험을 수행하였다. 실험시 수조의 압력은 시간의 경과에 따라 계속적으로 증가하였으나, 이는 방출된 증기의 불완전한 응축에 의한 것은 아니고 증기의 분출과 응축으로 인한 응축수의 부피팽창과 수조 온도의 상승으로 인한 증기압의 상승 때문인 것으로 판단된다.
North Korea invaded South Korea on June 25, 1950 and the armistice agreement was reached on July 27, 1953. After that, there have been about 5,000 provocations large and small. In particular, North Korea attacked a naval vessel called "Cheonanham" on March 26, 2010. After the attack, Korean government announced the sanctions against North Korea, so called "May 24 sanctions". North Korea bombarded Yeonpyeong provocation on November 23, 2010 and they planted wood box mines in the DMZ on August 4, 2015. The explosion of them resulted in injuring two Korean soldiers. In response to this accident, Korean government resumed loudspeaker broadcasting against North Korea in 11 years which had developed as the psychological warfare. After this, North Korea declared "being a state of war" and intensified tension. Suddenly North Korea suggested talks and two countries reached an agreement through inter-Korean high-level contacts. But we should review whether the agreement was reached with ease and in haste. This paper focuses on the North Korea's negotiating tactics and suggests our corresponding directions for the future.
Seo, J. M.;Kim, K. J.;Ihn, S.;Koo, S. J.;Park, Ch.;Kim, Y. K.
Journal of the Korean Vacuum Society
/
v.2
no.3
/
pp.288-293
/
1993
통전가열, 접촉냉각, 전기적 bias 및 시료 교환을 자유로이 할 수 있는 다기능의 새롭고 간단한 시료 고정장치를 저온 및 초고진공 상태에서 기체와 여러 방향의 시료표면 사이의 상호작용을 연구하기 위하여 고안하였다. 이 장치로써 2분 이내에 기판의 온도를 1600K에서 20K로 2분 이내에 냉각시킬 수 있었다. 그러므로 청결한 표면위에 수소나 He이나 Ne을 제외하고는 대부분의 기체를 흡착시킬 수 있게 되었다. 이러한 장치는 표면에서의 상변화, 기체와 표면의 화학반응의 연구에 중요하게 활용될 수 있다.
KSCE Journal of Civil and Environmental Engineering Research
/
v.26
no.3A
/
pp.513-521
/
2006
Many studies have been conducted on the high tension bolt friction connection in the view of the field practice. Those effort, however, unfortunately have not been appropriately applied in the design specifications. Recently, particularly for steel bridges, rationalization of design takes greater attention from designers and hence, demand on rationalization of high tension connection becomes more significant. The purpose of this study is to suggest direction for the rationalization of high tension bolt connection and to also provide fundamental information for the improvement of the design specifications. In order to accomplish the purposes, the design specifications in Korea was analyzed and compared with other specification from abroad, and was studied one of the most important factors including slip coefficient, and the specifications on the size of bolt holes. The effect of over-sized bolt hole and the reduction of axial force on bolt was evaluated through the experimental studies on the slippage of the high tension bolt connections. Other research topics included herein includes the difference of slip coefficients, the effect of over-sized bolt holes and the gap distance of members, and the application of filler plate and corrosion protected bolts. From the research results, it is known that the specifications in Korea apply a constant slip coefficient with respect to the contacted surface conditions while various coefficients are available depending on the contacted surface conditions. Therefore, it is recommended that the specifications in Korea also develop and detail the slip coefficient which can appropriately take account of the variation of the contacted surface conditions. It is also suggested that the limitation abroad on the over-sized bolt hole may be applied for enhancing the effectiveness of construction.
Journal of the Korean Society for Precision Engineering
/
v.15
no.1
/
pp.26-34
/
1998
In this paper, a force control algorithm for edge following task is suggested. Through the contact state modeling between rigid part and end-effector of robot, contact force and contact angle that are essencial parameters to build the control strategies for following movement of end-effector are derived. From these two parameters, we discriminate the every contact state into 8 cases and calculate the new moving position and direction simply. For the experiment. RX90 robot from Staubli with robot language V$^{+}$ is applied and F/T sensor is attached to the wrist of robot with RCC. Finally, 3 edge following experiments including the following of corner point are executed with successful results.s.
KSCE Journal of Civil and Environmental Engineering Research
/
v.33
no.5
/
pp.1947-1955
/
2013
The purpose of this paper is to present an photoelasticity technique for measuring the displacement and stress distribution in particle assembly subjected to shallow foundation loading. Photoelastic measurement technique was employed to visualize the force transmission of a particle assembly. A model assembly bounded by a steel frame was built by stacking bi-dimensional circular particles made of polycarbonate elastomer. Each particle was coated by a thin photoelastic sheet so that the force transmission represented by bright light stripes can be visualized. In a contacted particle, both magnitude and orientation of principal stress difference can also be measured via the photoelasticity technique. The different distributions of the contact stresses at the initial loading and near the failure were quantitatively compared. The photoelastic patterns and displacement fields observed in the pre-failure state disappears immediately after the buckling of confined force chains.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.