• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2011.04a
• /
• pp.388-392
• /
• 2011

화재 발생 시 연소확대 방지 및 이를 지연시켜 재실자의 피난시간을 확보하고자 실시하는 방염처리의 성능평가는 연소시험방법을 통해 잔염시간, 잔신시간, 탄화면적, 탄화길이가 일정기준에 적합하여야만 방염성능을 부여받게 되며 목재나 MDF와 같은 합판은 방염도료나 방염필름을 부착하여 사용하는 현장방염처리방법이 사용되고 있다. 따라서 본 연구에서는 시중에서 일반적으로 사용되고 있는 비방염 접착필름, 방염 필름, 방염 도료 등을 MDF 합판에 적용하여 방염처리 하였을 때의 연소특성 및 방염성능을 측정하였다.

• Journal of Adhesion and Interface
• /
• v.2 no.3
• /
• pp.16-24
• /
• 2001

The curing behavior of a phenolic resin (F/p: 1.3, 1.9, 2.5 for resol resin, F/P: 0.5, 0.7, 0.9 for novolac resin) has been studied by FT-IR spectroscopy. In this study is to synthesis of resol and novolac type phenolic resin with different F/P molar ratios and to compare the level of cure at different curing temperature conditions ($130^{\circ}C$, $160^{\circ}C$, $180^{\circ}C$ for resol resin, $160^{\circ}C$, $170^{\circ}C$, $180^{\circ}C$ for novolac resin) for 3, 5, 7, 10, 20, and 60 (min.), respectively. The conversion (${\alpha}$) was determined by the ratio of the peak area with time to the peak area of non-baked phenolic QH ($3300cm^{-1}$) at spectra. It is concluded that the initial curing rate of resol and novolac resin was increased as the molar ratio of formaldehyde/phenol increased and as the curing temperature of resin increased. According to the analysis was by the homogenous first-order model, the initial curing rate of resol and novolac resin was increased as the molar ratio of formaIdehyde/phenol increased at specific curing temperature.

• Composites Research
• /
• v.30 no.4
• /
• pp.229-234
• /
• 2017

Generally, joints are the weakest part in the composite structures. Composite joints can be classified into adhesive joints and mechanical joints, and mechanical joints are mainly used in areas less sensitive to environmental conditions. In this paper, the failure loads of composite mechanical joints with five different stacking angles are tested and predicted. Finite element analysis of mechanical joints were performed and failure loads were predicted by the FAI(Failure Area Index) method using Tsai-Wu and Yamada-Sun failure criteria, and the predicted failure loads were compared with experimental results. From the experiment and analysis, the failure loads of the mechanical joints were decreased as the ratio of 0 degree layer was low and they could be predicted within 13.03% using the FAI method and Yamada-Sun failure criteria.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.15 no.2
• /
• pp.357-363
• /
• 1995

Disbond size of adhesively bonded single lap and double lap joints CFRP composite specimens has been evaluated using acousto-ultrasonic(AU) technique. Frequency spectra for all specimens were obtained by measuring peak amplitude of the stress wave propagated through the bond-lines. By analyzing these frequency spectra, peak amplitude was found to be proportional to fractional bonding area and to be maxima at the fundamental and the third order higher harmonic frequencies of specimen thickness mode. The disbond size can be evaluated quantitatively and this technique can be applied to real structures if the reference specimens are prepared in advancve.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.4
• /
• pp.435-442
• /
• 2010

The efficiency of the car's wiper blade has a great contribution to the guarantee of security. To guarantee the wiper blade's ability of getting rid of dust sticking on the glass surface, the qualities of lubricant, durability, heat resistant, low temperature, ozone resistant, chemical resistant must be good as well as it being noiseless. Like this, in order to improve the wiper's skills, it is essential to have a system that is able to assess and analyse the properties of the wiper. In this paper, to create a system that measures the car's wiper pressure, an analog/digital converter (ADC) that receives signals generated from the pressure sensor and transmits it to a personal computer is proposed. The designed ADC is one of the pipeline ADCs that can obtain fast movement rate and also a structure that can optimize the entire system's area as well as the consumption of strength.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.125-131
• /
• 2011

The effects of chopped kenaf fiber concentration on mechanical property of polypropylene (PP) composite are investigated. The addition of kenaf increased the tensile strength, flexural modulus, impact strength, specific gravity, and HDT, while decreased the elongation%, flexural strength, and melt flow index. The increase of mechanical properties is due to increased surface area contacting between fiber and polymer matrix and fiber-fiber interaction. Volatile extractives in the kenaf seemed to decrease the interfacial adhesion between kenaf surface and PP.

• Composites Research
• /
• v.31 no.4
• /
• pp.171-176
• /
• 2018

We proposed new and easy fabrication method of micro-nano hierarchical structures for synthetic dry adhesives and conducted feasibility tests of alignment characteristics of nano-materials in the microstructures by capillary effect. Candidates of fabrication conditions were selected based on the degree of cure and viscosity of mixtures of multiwall carbon nanotubes (MWCNTs) and polydimethylsiloxane (PDMS), which were measured with respect to the fabrication conditions. Scanning electron microscopy images of cross sections of MWCNT-PDMS microstructures were analyzed. MWCNT alignment in microstructures was better when fabrication temperature and degree of cure at fabricating start were lower, but areal density of MWCNTs was little affected by fabrication conditions.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.59-59
• /
• 2011

초극세 섬유는 종래의 섬유와 비교해서 매우 가늘고 큰 표면적을 지니므로 섬유고분자 고유의 성질 이외에 활성이 높은 섬유표면이 가지는 특수한 성질의 기여가 매우 커지게 되므로 흡착특성이나 접착특성 등 특수한 성질의 기여가 매우 커지게 된다. 초극세 섬유를 제조하는 방법은 통상적으로 멜트블로운법, 플래쉬법, 전기방사법 그리고 해도형 복합방사법의 4가지로 분류된다. 그중 해도형 복합방사법은 가장 안정적인 방법으로 PET기준으로 0.01데니어 급까지 상용화가 되어 있다. 해도형 복합섬유의 개발에 있어서 중요한 것 중에 하나가 해성분 폴리머의 용출기술이다. 초극세화를 목적으로 해성분인 변성폴리에스테르를 제거시키기 위해서 실시되는 알칼리(NaOH)에 의한 감량공정은 그 처리조건에 따라서 초극세사로 잔존해야하는 도성분의 정규 폴리에스테르까지 손상시킬 수 있기 때문에 균일한 용출조건의 확립은 매우 중요하다. 그러나 초극세화가 진행될수록 알칼 리가 섬유 내부까지 균일하게 침투하기가 어려우며 감량된 도성분도 비표면적이 증가하기 때문에, 해성분의 균일한 용출 및 감량을 위한 안정적인 조건을 선정하기가 어렵다. 본 연구에서는 코오롱FM에서 새롭게 개발한 800nm급 해도형 초극세사 제품의 감량특성에 대하여 고찰함으로써 제품화에 필요한 요소 기술의 기초를 마련하고자 한다. 유기산을 이용한 전처리가 해도형 초극세 폴리에스테르 섬유의 해성분 감량 특성에 미치는 영향에 대하여 조사하고, 알칼리 감량시 NaOH의 농도, 처리시간 및 처리온도별 감량특성에 대하여 고찰하였다.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.13 no.2
• /
• pp.129-136
• /
• 1991

The fibrin sealant was first designed as an alternative to surgical suture for the purpose of surface-to-surface union especially in parenchymal organs like the liver, spleen and kidney. The clinical application of currently used fibrin sealant was first introduced in 1972. The fibrin sealant consists of principal two components; lyophilized human fibrinogen and bovine thrombin. The fibrinogen component also contains coagulation factor XIII. A solution of aprotinin, an inhibitor of fibrinolysis is used to dissolve the fibrinogen and to provide the first component, and a solution of calcium chloride is also used to provide the second component. From July to December in 1990, during 6 months, we used fibrin sealant in the 28 patients of 33 various cases, in the following ways; supportive application of fibrin sealant after free autogenouse nerve graft for the repair of inferior alveolar nerve, facial nerve or accessory nerve, treament of hemangioma or lymphangioma to thrombosize and lead to the tumor shrinking, skin grafting to stimulate the adhesion and tissue repair, bone grafting in the patients of cleft alveolus, mandibular reconstruction or orthognathic surgery to facilitate the knitting of bone chips, tissue adhesion after tumor resection, radical neck dissection or flap reconstructions, and supportive adhesion of external auditory cannal after TMJ surgery via postauricular approach. No adverse effects were observed, none of the patients developed hepatitis or other blood transmitted disease, and the wound healing were acceptable.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.301-308
• /
• 2014

Despite Korea forest take 63.7% of the nation's territory, productivity of domestic structural lumber is low. Studies of domestic small lumbers need to be improved domestic structural timber productivity. In this study, small diameter lumber and finger joint small diameter lumber took bending test to calculate MOE and MOR. MOE of small diameter lumber was $9.3kN/mm^2$ and MOE of finger joint small diameter lumber was $15.4kN/mm^2$. Allowable standard bending stress of small diameter lumber and finger joint small diameter lumber was calculated according to ASTM D 2915. Standard allowable bending stress of small diameter lumber was $12N/mm^2$ and standard allowable bending stress of finger joint small diameter lumber was $11N/mm^2$. Standard allowable bending stress of finger joint small diameter lumber should be considered to design structural beam members.